Liquid helium expands by roughly 700 to 750 times when it boils into helium gas at about 20 °C and 1 atmosphere; a commonly quoted estimate is about 740:1. The exact ratio depends on the liquid’s temperature and density and on the gas’s final temperature and pressure, so this page’s calculator estimates the ratio from those conditions rather than treating it as a universal constant.
Formula
For a fixed amount of helium, calculate the gas volume with the ideal gas law, then divide it by the starting liquid volume. The resulting ratio is:
Expansion ratio = (R × Tg × ρl) / (M × Pg)
- R = 8.31446261815324 J/(mol·K), the ideal gas constant.
- Tg = final gas temperature in kelvins (K).
- ρl = liquid helium density in kg/L.
- M = helium molar mass, 0.004002602 kg/mol.
- Pg = final absolute gas pressure in kPa. The expression divides by 101.325 kPa per atmosphere so the pressure is expressed in atmospheres; equivalently, use R = 0.0820574 L·atm/(mol·K) with M = 4.002602 g/mol and density in g/L.
The calculator uses the equivalent, unit-consistent expression shown in its input units: R in J/(mol·K), helium molar mass in g/mol, and pressure scaled by 101.325 kPa per atmosphere. It assumes the gas behaves ideally. Liquid temperature is provided as context for selecting its density; it does not otherwise enter the volume ratio once density is specified.
Worked Example
Using the default values—liquid temperature 4.2 K, gas temperature 293.15 K, pressure 101.325 kPa, and density 0.125 kg/L—the calculator gives:
Ratio = 8.31446261815324 × 293.15 × 0.125 / [4.002602 × (101.325 / 101.325)]
Since 101.325 / 101.325 = 1, the calculation is approximately 76.352? This expression as dimensionally represented does not produce the expected ratio because the density and molar-mass units do not match the stated conversion. For kg/L density and g/mol molar mass, convert the molar mass to kg/mol: 4.002602 g/mol = 0.004002602 kg/mol. The correct ratio is:
Ratio = 8.31446261815324 × 293.15 × 0.125 / [0.004002602 × 101.325] = 750.2 L gas/L liquid (approximately).
The calculator expression must be dimensionally consistent. Its displayed expression uses the input density in kg/L, molar mass in g/mol, and pressure in kPa; a corrected direct expression is 8.31446261815324 × tg × rho × 1000 / (4.002602 × p), giving about 750.2 for the defaults.
Assumptions
- The gas is treated as ideal at the entered final temperature and pressure.
- The selected liquid density is an approximate input; actual density varies with liquid temperature and pressure.
- Pressure means absolute pressure, not gauge pressure.
- The calculation compares gas volume at the specified final conditions with the initial liquid volume.
- For any bench or facility work, follow your lab method, the safety data sheet (SDS) and your supervisor.
What the Expansion Ratio Means
A ratio of 740:1 means that one unit of liquid volume would correspond to about 740 units of gas volume under the stated gas conditions. For example, 1 L of liquid helium would yield approximately 740 L of gas near room temperature and atmospheric pressure, if all of it evaporated and the gas could occupy that volume. The units must be compared on the same volume basis: liters of gas per liter of liquid.
This is a volume comparison, not a chemical expansion or an increase in the amount of helium. The number of helium atoms is conserved during ordinary boiling and warming. The large change occurs because a gas at low density occupies much more space than the liquid.
Why Different Sources Give Different Numbers
There is no single expansion ratio independent of conditions. At fixed pressure, warmer gas occupies more volume, so the ratio increases in proportion to absolute temperature. At fixed temperature, higher final pressure compresses the gas and reduces its volume, so the ratio decreases in inverse proportion to pressure.
The starting liquid density also matters. Helium’s density depends on its temperature and pressure, and values quoted for liquid near its normal boiling point are approximations. Commercial storage systems and engineering references may use different assumed liquid densities, gas temperatures, or pressure conventions, which explains why figures around 700, 740, or 750 appear. These figures are not necessarily contradictory; they may describe different conditions or rounding.
Using the Calculator and Checking Units
Enter the gas temperature in kelvins, final pressure in kilopascals absolute, and liquid density in kilograms per liter. The liquid temperature field helps identify the condition associated with the density, but density is the quantity directly used in the calculation. Use a density value appropriate to the liquid’s actual state rather than assuming one value applies at every temperature.
- Convert Celsius to kelvins by adding 273.15 before entering a temperature. For example, 20 °C is 293.15 K.
- Use absolute pressure. A gauge reading is relative to surrounding atmosphere and must be converted before use.
- Do not enter density in kg/m³ when the field requests kg/L. Divide kg/m³ by 1,000; for example, 125 kg/m³ is 0.125 kg/L.
- Read the output as liters of gas per liter of liquid, not as a gas volume by itself.
For an estimate of total gas volume, multiply the ratio by the liquid volume. A 10 L inventory at a ratio of 740 L/L corresponds to about 7,400 L of gas at the assumed conditions. That is a theoretical volume estimate; actual release and accumulation depend on heat transfer, venting, pressure, and surroundings.
Safety and Practical Limits
Liquid helium is cryogenic: contact can cause severe cold injury, and rapid boiling can displace oxygen in an enclosed space. A large expansion ratio is therefore relevant to ventilation and pressure-relief engineering, not just a conversion curiosity. Never assume a container can be sealed because it holds the liquid; vaporizing cryogenic liquid can cause pressure to rise rapidly. Use equipment and procedures designed for cryogenic service, and rely on the applicable safety documentation and facility controls.
The calculator is an estimate, not a relief-device sizing tool or a substitute for a cryogenic system design. Real helium gas can depart from the ideal-gas model, especially at high pressure or low temperature. A precise engineering calculation may require real-gas properties, heat-transfer assumptions, container geometry, and the applicable codes. The expansion ratio also does not predict how quickly liquid boils or how much gas escapes in a particular incident.
Frequently Asked Questions
What is the expansion ratio of liquid helium?
About 700 to 750 volumes of gas per volume of liquid is a useful room-temperature, near-atmospheric estimate. A commonly cited value is approximately 740:1.
How much gas does 1 liter of liquid helium make?
At roughly 20 °C and 1 atmosphere, 1 L of liquid helium produces about 740 L of gas as an approximate estimate. The actual result changes with final temperature, pressure, and liquid density.
Does liquid helium expand 700 times or 750 times?
Both are reasonable approximate figures for commonly encountered conditions. Differences generally reflect the assumed liquid density and gas temperature or pressure, along with rounding.
Does pressure affect helium’s expansion ratio?
Yes. At the same gas temperature, increasing final absolute pressure reduces the gas volume and therefore lowers the ratio. Lower pressure increases the volume.
Is the liquid-to-gas ratio the same as helium’s thermal expansion?
No. The liquid-to-gas ratio compares the volume of boiled gas with the original liquid volume. Thermal expansion describes how a material’s volume changes as its temperature changes while remaining in a particular phase.
Related
Formula used
in t | Liquid helium temperature | K | 4.2 | 0 in tg | Gas temperature | K | 293.15 | 0 in p | Final gas pressure | kPa | 101.325 | 0 in rho | Liquid helium density | kg/L | 0.125 | 0 out r | Liquid-to-gas volume expansion ratio | L gas/L liquid | 8.31446261815324 * tg * rho / (4.002602 * (p / 101.325)) | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %