molecalculator

Moles & Molar Mass

LPG Liquid-to-Gas Expansion Ratio Calculator

Calculator No. 01-3391 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator estimates how much LPG vapour a liquid volume would make at a selected temperature and pressure, using the ideal-gas equation and an LPG molar mass you supply. Enter the liquid volume, liquid density, LPG molar mass, and gas conditions to get the gas volume and the liquid-to-gas expansion ratio; the result is an estimate, not a universal fixed ratio.

Formula

The calculator first converts liquid LPG into moles using its mass and molar mass, then estimates the vapour volume with the ideal-gas law. In symbols:

  • Liquid mass, m = VL × ρ, where VL is liquid volume in L and ρ is liquid density in kg/L. Convert kilograms to grams by multiplying by 1000.
  • Amount, n = m / M, where M is LPG molar mass in g/mol.
  • Gas volume, Vg = nRT / P.
  • Expansion ratio = Vg / VL.

The gas constant used is R = 8.31446261815324 J/(mol·K), equivalent to 8.31446261815324 kPa·L/(mol·K). Temperature is converted from Celsius to kelvin by adding 273.15. Pressure must be absolute pressure in kPa, not gauge pressure. Since the same liquid volume appears in the numerator and denominator of the ratio, the ratio depends on density, molar mass, temperature, and pressure, not on the chosen sample size.

Worked Example

Using exactly the defaults shown above: 1 L of liquid LPG, density 0.54 kg/L, molar mass 51.5 g/mol, gas temperature 15 °C, and absolute pressure 101.325 kPa.

  1. Liquid mass = 1 L × 0.54 kg/L = 0.54 kg = 540 g.
  2. Amount of LPG = 540 g / 51.5 g/mol = 10.485 mol (rounded).
  3. Temperature = 15 + 273.15 = 288.15 K.
  4. Gas volume = 10.485 mol × 8.31446261815324 kPa·L/(mol·K) × 288.15 K / 101.325 kPa ≈ 247.9 L.
  5. Expansion ratio = 247.9 L / 1 L = 247.9 L/L, or 248:1 to three significant figures.

The calculator displays the ratio and volume to three decimal places, so the displayed outputs are approximately 247.9 L/L and 247.9 L for these defaults.

Assumptions

  • The LPG is represented by one effective molar mass and one liquid density; actual fuel composition varies.
  • The gas is treated as ideal, with no correction for non-ideal behaviour or interactions.
  • The result refers to the specified gas temperature and absolute pressure, not to a fixed standard condition.
  • All liquid LPG is assumed to vaporize, with no residual liquid or heat-transfer limitation represented.

What the Expansion Ratio Means

LPG is a broad name for liquefied petroleum gas, commonly based on propane, butane, or blends. It is kept as a liquid under pressure, which allows a relatively large amount of fuel to be stored in a compact volume. When it becomes vapour at a stated pressure and temperature, that same quantity occupies a much larger volume. The expansion ratio expresses the comparison: a value of 248 L/L means one litre of liquid would correspond, under the modelled conditions, to about 248 litres of gas.

There is no single ratio valid for every LPG container or use. Propane and butane have different molar masses and liquid densities, and commercial blends vary by season and location. The gas volume also changes with its temperature and pressure. A ratio quoted without its reference conditions and the LPG composition is therefore incomplete.

Choosing Inputs and Reading the Result

  • Liquid density: use a value for the actual LPG blend and its liquid temperature where possible. The default 0.54 kg/L is a practical example, not a universal constant; propane-rich and butane-rich liquids differ.
  • Molar mass: pure propane is about 44.10 g/mol and pure n-butane about 58.12 g/mol. For a blend, use a representative composition-based average if available. If composition is unknown, the calculator cannot produce a precise blend-specific answer.
  • Gas temperature: enter the temperature of the vapour condition being compared. The equation uses kelvin internally, so temperatures below absolute zero are not physically meaningful.
  • Gas pressure: enter absolute pressure. At approximately sea-level atmospheric conditions, this is about 101.325 kPa. Gauge pressure measures above local atmospheric pressure and must have atmospheric pressure added before using this equation.

The ratio is useful for understanding the large change in volume during vaporization, while the gas-volume output scales with the liquid quantity. For example, doubling liquid volume doubles the estimated gas volume if all other inputs stay the same. The ratio itself remains unchanged.

Why Published Ratios Differ

Reference figures can differ substantially because their assumptions differ. A comparison may use pure propane rather than a mixed LPG, a different liquid density, a different temperature, or a pressure other than one atmosphere. Some sources also use measured real-gas properties, while this calculator uses the ideal-gas law. At higher pressures, real gases can depart from ideal behaviour, so a more detailed equation of state or published property data may be needed.

A common mistake is to treat a familiar approximate ratio as an exact property of LPG. It is better to report the conditions alongside the number—for example, the composition or representative molar mass, liquid density, gas temperature, and absolute pressure. For engineering design, equipment sizing, or regulatory calculations, use the relevant fuel specification and validated property data rather than this simplified estimate.

Limits and Safety Context

This calculation describes a change in volume; it does not predict how quickly LPG vaporizes, the vapour pressure above a liquid, the amount a regulator can supply, or the safe capacity of a vessel. Vaporization absorbs heat, so actual evaporation can cool the remaining liquid and surrounding equipment. Real installations also depend on ventilation, pressure controls, pipe dimensions, ambient conditions, and applicable codes.

LPG vapour is flammable, and a leak can create a fire or explosion hazard. It can also displace oxygen in a confined area. Never use an expansion estimate to justify releasing LPG, testing for leaks with a flame, or altering a pressurized system. Follow the equipment instructions and local safety requirements; if a leak is suspected, leave the area and contact emergency services or the appropriate qualified authority.

Frequently Asked Questions

What is the expansion ratio of LPG from liquid to gas?
It depends on the LPG blend and the temperature and pressure of the resulting gas. A rough figure often used for illustration is around 250 volumes of vapour per volume of liquid near atmospheric pressure, but it should not be treated as exact or universal.

How many litres of gas does 1 litre of LPG make?
Under the calculator’s default assumptions, one litre of liquid corresponds to about 247.9 L of vapour at 15 °C and 101.325 kPa absolute. Different LPG composition or conditions change that estimate.

Does propane expand more than butane?
The exact liquid-to-gas volume ratio depends on the comparison conditions and the liquid density as well as molar mass. Propane and butane have different physical properties, so do not apply one gas’s ratio to the other without specifying conditions.

Is LPG expansion ratio the same at every temperature?
No. At a fixed amount and pressure, ideal-gas volume increases in proportion to absolute temperature. Pressure changes matter too: at fixed temperature, the calculated volume decreases as absolute pressure rises.

Should I use gauge or absolute pressure?
Use absolute pressure in this formula. If a reading is gauge pressure, add local atmospheric pressure to convert it to absolute pressure; for example, near sea level add about 101.325 kPa.

Related

Formula used
in vl | Liquid LPG volume | L | 1 | 0
in rho | Liquid LPG density | kg/L | 0.54 | 0.001
in mm | LPG molar mass | g/mol | 51.5 | 1
in t | Gas temperature | °C | 15 | -273.15
in p | Gas pressure | kPa absolute | 101.325 | 0.001
out ratio | Gas volume per liquid volume | L/L | (vl * rho * 1000 / mm * 8.31446261815324 * (t + 273.15) / (p / 1000)) / vl | 3
out vg | Estimated gas volume | L | vl * rho * 1000 / mm * 8.31446261815324 * (t + 273.15) / (p / 1000) | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →