molecalculator

Moles & Molar Mass

Mass by Volume Percentage Formula

Calculator No. 01-9127 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Mass by volume percentage (often abbreviated as % w/v) is the mass of a solute in grams dissolved in 100 milliliters of final solution. The formula is: % w/v = (mass of solute in grams ÷ volume of solution in milliliters) × 100. You enter the solute mass and the final solution volume, and the calculator returns the percentage concentration.

Formula

The mass by volume percentage is defined as:

% w/v = (mass of solute (g) ÷ volume of solution (mL)) × 100%

Where:

  • mass of solute is in grams (g)
  • volume of solution is in milliliters (mL) — this is the final volume after the solute has been added and the solution has been made up to the mark, not the volume of solvent alone

The result is a percentage with units of g/mL implicitly (since grams per 100 mL is the same as g/100 mL). For example, a 5% w/v solution contains 5 g of solute in every 100 mL of solution.

Note that this is different from mass by mass percentage (% w/w), which uses grams of solute per 100 g of solution, and from volume by volume percentage (% v/v), which uses mL of solute per 100 mL of solution. The w/v form is common in biology and medicine for preparing solutions from solid reagents, because it is easy to measure mass and volume directly.

Worked Example

Using the default values from the calculator: you have 2.922 g of sodium chloride (NaCl, molar mass 58.44 g/mol) and you want to prepare 250 mL of solution. What is the mass by volume percentage?

  1. Write down the formula: % w/v = (mass of solute ÷ volume of solution) × 100
  2. Plug in the numbers: % w/v = (2.922 g ÷ 250 mL) × 100
  3. Divide: 2.922 ÷ 250 = 0.011688
  4. Multiply by 100: 0.011688 × 100 = 1.1688%

So the solution is 1.1688% w/v (or approximately 1.17% w/v). This means that in every 100 mL of this solution, there are 1.1688 g of NaCl.

For comparison, the molarity of this solution is calculated as: moles of NaCl = 2.922 g ÷ 58.44 g/mol = 0.05000 mol. Molarity = 0.05000 mol ÷ 0.250 L = 0.2000 mol/L. This matches the calculator’s first output of 0.2 M (rounded to 4 decimal places).

Assumptions

  • The solute is completely dissolved and the solution is homogeneous.
  • The volume used is the final volume of the solution, not the volume of solvent added. This is a critical distinction: if you add 250 mL of water to 2.922 g of NaCl, the final volume will be slightly more than 250 mL, and the concentration will be slightly lower than calculated.
  • The density of the solution is not used in this calculation; w/v percentage does not require density.
  • The solute is a solid (or a pure liquid) measured by mass; the solvent is typically water but can be any liquid.

When to Use Mass by Volume Percentage

Mass by volume percentage is used when you need to describe a concentration in a way that is easy to prepare with standard lab equipment (a balance and a volumetric flask). Common applications include:

  • Preparing salt solutions (e.g., saline) where the concentration is given as a percentage.
  • Making up buffers or media in biology labs (e.g., 1% agarose gel is 1 g agarose per 100 mL buffer).
  • Diluting stock solutions when the label states % w/v.
  • In pharmaceutical compounding, many simple solutions are prescribed as % w/v (e.g., 5% dextrose in water means 5 g dextrose per 100 mL final solution).

It is especially useful when you do not know the molar mass of the solute or when you are working with mixtures (like plant extracts) where the exact molecular weight is not defined.

How to Prepare a % w/v Solution Correctly

  1. Weigh the required mass of solute accurately on a balance.
  2. Transfer the solute to a volumetric flask (or a graduated cylinder if a volumetric flask is not available).
  3. Add about half of the final volume of solvent (e.g., 50 mL for a 100 mL solution) and swirl to dissolve the solute completely.
  4. Once dissolved, add solvent up to the calibration mark on the flask. The bottom of the meniscus should sit exactly on the mark.
  5. Stopper and invert the flask several times to mix thoroughly.

This procedure ensures that the final volume is exactly the desired volume, not the sum of solute volume plus solvent volume. This is the most common source of error in preparing % w/v solutions.

Common Mistakes and Misconceptions

  • Using the volume of solvent instead of the final volume. If you add 100 mL of water to 5 g of salt, the final volume is not exactly 100 mL. Always use a volumetric flask and make up to the mark.
  • Confusing % w/v with % w/w. A 10% w/w solution is 10 g solute per 100 g solution (which includes the mass of solute and solvent). A 10% w/v solution is 10 g solute per 100 mL solution. They are not the same unless the solution density is exactly 1 g/mL.
  • Forgetting the units. The mass must be in grams and the volume in milliliters. If you have mass in kilograms or volume in liters, convert first: 1 kg = 1000 g, 1 L = 1000 mL.
  • Assuming % w/v is the same as % v/v. For liquids, a 10% v/v solution is 10 mL of solute per 100 mL solution, which is different from 10 g of solute per 100 mL solution unless the liquid’s density is 1 g/mL.

Relationship to Molarity

Mass by volume percentage and molarity are both concentration measures, and you can convert between them if you know the solute’s molar mass. The relationship is:

Molarity (mol/L) = (% w/v × 10) ÷ molar mass (g/mol)

Because % w/v is grams per 100 mL, multiplying by 10 gives grams per liter. For example, a 5% w/v solution of a substance with molar mass 100 g/mol has a molarity of (5 × 10) ÷ 100 = 0.5 mol/L.

The calculator on this page performs this conversion for you: it takes the mass and volume, computes the molarity, and also shows the concentration in millimolar (mM). The default example shows that a 1.1688% w/v NaCl solution is 0.2 mol/L (200 mM).

Frequently Asked Questions

What does % w/v mean exactly?

% w/v stands for mass by volume percentage. It is the number of grams of solute in 100 milliliters of final solution. For example, 0.9% w/v NaCl is 0.9 g of NaCl in every 100 mL of solution — this is the concentration of normal saline.

How do I convert % w/v to mg/mL?

Since % w/v is grams per 100 mL, you can convert to mg/mL by multiplying by 10. For instance, 5% w/v = 5 g/100 mL = 5000 mg/100 mL = 50 mg/mL. This is a handy conversion for preparing solutions from stock concentrations given in mg/mL.

Is % w/v the same as % w/w?

No. % w/v uses mass of solute per volume of solution (g/100 mL), while % w/w uses mass of solute per mass of solution (g/100 g). They are equal only when the solution density is exactly 1 g/mL, which is rarely true for concentrated solutions. Always check which one is intended.

What if I add solute to the solvent and the volume changes?

That is exactly why you must use a volumetric flask and make up to the final volume. If you add 5 g of salt to 100 mL of water, the final volume will be about 103 mL, so the concentration will be lower than 5% w/v. To get an exact 5% w/v solution, dissolve the salt in a small amount of water, then add water until the total volume is 100 mL.

Can I use % w/v for any solute?

Yes, as long as the solute is a solid or a pure liquid that you can weigh. It is commonly used for salts, sugars, and polymers. For gases, % w/v is not practical; you would use molarity or partial pressure instead.

How do I prepare a solution if I only have the molarity?

Convert molarity to % w/v using the formula: % w/v = (molarity × molar mass) ÷ 10. For example, to make 0.5 M NaCl (molar mass 58.44 g/mol), the % w/v is (0.5 × 58.44) ÷ 10 = 2.922% w/v. Then weigh 2.922 g of NaCl and make up to 100 mL.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →