Mean free path is the average distance a particle travels between collisions, and you calculate it with the formula λ = 1 / (√2 · π · d² · n), where d is the particle diameter and n is the number density of particles. Enter the gas temperature, pressure, and molecular diameter into the calculator below to get the mean free path in meters.
Formula
The mean free path λ is given by:
λ = kB·T / (√2 · π · d² · p)
where:
- λ = mean free path (m)
- kB = Boltzmann constant = 1.380649 × 10−23 J/K
- T = absolute temperature (K)
- d = molecular diameter (m)
- p = pressure (Pa)
This is the standard kinetic theory result for a hard-sphere gas. The √2 factor accounts for the relative motion of two colliding molecules. You can also write it using the ideal gas law as λ = 1/(√2 · π · d² · n), where n = p/(kB·T) is the number density (molecules per cubic meter).
Worked Example
Using the defaults: T = 25 °C = 298.15 K, p = 101.325 kPa = 101325 Pa, d = 370 pm = 3.70 × 10−10 m.
- Calculate kB·T = 1.380649 × 10−23 × 298.15 = 4.1164 × 10−21 J
- Calculate d² = (3.70 × 10−10)² = 1.369 × 10−19 m²
- Calculate π·d² = 3.14159 × 1.369 × 10−19 = 4.301 × 10−19 m²
- Multiply by √2 and p: √2 × 4.301 × 10−19 × 101325 = 6.163 × 10−14 N
- Divide: λ = 4.1164 × 10−21 / 6.163 × 10−14 = 6.68 × 10−8 m = 66.8 nm
The calculator returns 66.8 nm, matching the step-by-step result.
Assumptions
- The gas is ideal: molecules are hard spheres with no intermolecular forces except at collisions.
- All molecules are identical and have the same diameter d.
- The gas is in thermal equilibrium at temperature T.
- Pressure is low enough that the gas behaves ideally (typically below a few atmospheres).
What the Result Means
The mean free path tells you how far a molecule travels before bumping into another. At room temperature and atmospheric pressure, air molecules have a mean free path of roughly 68 nm – about 200 times the diameter of a nitrogen molecule. This is why diffusion is slow in gases: even though molecules move at hundreds of meters per second, they collide constantly and change direction.
When the mean free path is much larger than the container dimensions, you are in the free-molecular regime (vacuum technology). When it is much smaller, you are in the continuum regime (ordinary fluid dynamics). The ratio of mean free path to a characteristic length is the Knudsen number, which determines which flow equations apply.
How to Choose the Molecular Diameter
The diameter is not a fixed physical constant – it depends on how you define a collision. Common values for gases at room temperature are:
- Helium: 260 pm
- Hydrogen (H₂): 290 pm
- Nitrogen (N₂): 370 pm
- Oxygen (O₂): 360 pm
- Carbon dioxide (CO₂): 450 pm
These are effective hard-sphere diameters from viscosity measurements. For mixtures, you would need an average diameter based on the collision cross-section between different species – the simple formula above applies to a pure gas.
Common Mistakes and Pitfalls
- Unit mix-ups: The most frequent error is using pressure in kPa without converting to Pa. Always convert kPa to Pa (multiply by 1000) and pm to m (multiply by 10−12).
- Forgetting temperature in Kelvin: Use K, not °C. Add 273.15 to Celsius values.
- Using the wrong diameter: Some sources list the van der Waals diameter, which is larger than the kinetic-theory diameter. Stick to values from viscosity or diffusion experiments.
- Ignoring the √2: The √2 factor is essential; omitting it gives a result that is about 41% too large.
Limits of the Formula
The hard-sphere model is a simplification. Real molecules have attractive and repulsive forces, so the effective collision cross-section changes with temperature. At high pressures, the gas is no longer ideal and the mean free path becomes shorter than predicted. At very low temperatures, quantum effects can become important. For most engineering and vacuum applications, however, the hard-sphere formula is accurate to within a few percent.
Frequently Asked Questions
What is the mean free path of air at room temperature?
At 25 °C and 1 atm (101.325 kPa), using an average air molecule diameter of about 370 pm, the mean free path is approximately 68 nm. This is the typical value quoted for air under standard conditions.
How does pressure affect mean free path?
Mean free path is inversely proportional to pressure. If you double the pressure, you halve the mean free path. This is why vacuum systems have much longer mean free paths – at 10−6 Pa, the mean free path can be kilometers.
Does temperature affect mean free path?
Yes, but only through the absolute temperature. Mean free path is directly proportional to T (in Kelvin). Raising the temperature from 25 °C to 100 °C increases the mean free path by about 25% (from 298 K to 373 K).
What is the difference between mean free path and mean free time?
Mean free path is the average distance between collisions; mean free time is the average time between collisions. They are related by the average speed: mean free time = mean free path / average speed. The average speed depends on temperature and molecular mass.
Why is the √2 in the formula?
Because both molecules are moving. The relative speed between two molecules is √2 times the average speed of a single molecule in the gas. This increases the collision rate, so the mean free path is shorter by a factor of √2 compared to a stationary-target model.
Can I use this for liquids or solids?
No. The mean free path concept is for gases where molecules are far apart. In liquids and solids, molecules are in constant contact, and the mean free path is on the order of the molecular spacing (a few tenths of a nanometer). The hard-sphere gas formula does not apply.
Related
Formula used
in t | Temperature | °C | 25 | -273.15 | 2000 in p | Pressure | kPa | 101.325 | 0.001 | 100000 in d | Molecular diameter | pm | 370 | 50 | 2000 out lambda | Mean free path | nm | (8.31446261815324 * (t + 273.15)) / (sqrt(2) * pi * (d * 1e-12)^2 * (p * 1000)) * 1e9 | 3 out coll | Collision frequency | 1/s | sqrt(2) * pi * (d * 1e-12)^2 * (p * 1000) / (8.31446261815324 * (t + 273.15)) * sqrt(8 * 8.31446261815324 * (t + 273.15) / (pi * 0.02897)) | 0
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- ug to ppb Calculator: Convert Micrograms per Liter1.00 ppb
- Grams to Moles Chemistry: How to Convert0.2000 mol/L
- Convert ug/l to ppb Calculator
- CPP Calculator Ontario: How CPP Is Calculated162.12 $/month
- Organic Chemistry Reaction Calculator: How It Works
- Grams to Moles to Molecules: How to Convert0.2000 mol/L