molecalculator

Moles & Molar Mass

Mesh Current Analysis Calculator

Calculator No. 01-9984 · Updated · Formula and assumptions shown below

Mesh current I1 -2.400 A
Mesh current I2
1.800 A
Result, rounded to 3 decimal places
Number of meshes
2
Set in the form below
R1 (ohm)
10 ohm
Set in the form below
You enter
Number of meshes, R1 (ohm) (ohm), R2 (ohm) (ohm), R3 (ohm) (ohm), V1 (volt) (V), V2 (volt) (V)
You get
Mesh current I1 (A), Mesh current I2 (A)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A mesh current analysis calculator solves a planar electrical circuit for the current flowing in each independent loop (mesh) when you enter the resistor values and voltage sources. You provide the circuit’s mesh resistances and source voltages, and the calculator returns the mesh currents in amperes, which you can then use to find branch currents and voltages. This page explains the method, shows you how to set up the equations, and gives a worked example you can verify by hand.

Formula

For a circuit with two meshes, the mesh current method writes Kirchhoff’s voltage law (KVL) around each mesh. In matrix form for a two-mesh circuit:

[ R11 -R12 ] [ I1 ] [ V1 ]
[ -R12 R22 ] [ I2 ] = [ V2 ]

Where:
R11 = sum of all resistances in mesh 1 (Ω)
R22 = sum of all resistances in mesh 2 (Ω)
R12 = resistance shared between mesh 1 and mesh 2 (Ω) – note it appears with a negative sign in the matrix because the two mesh currents flow in opposite directions through it
V1 = algebraic sum of voltage rises in mesh 1 (V) – a source that pushes current in the direction of the mesh arrow is positive
V2 = algebraic sum of voltage rises in mesh 2 (V)
I1 = mesh current 1 (A)
I2 = mesh current 2 (A)

Solving the 2×2 system gives:

I1 = (V1·R22 + V2·R12) / (R11·R22 – R12²)
I2 = (V1·R12 + V2·R11) / (R11·R22 – R12²)

Note the sign of the V2 term in the numerator: in the calculator above, the expression uses (v1*r22 – v2*r12) for I1 and (r11*v2 – r12*v1) for I2, which matches the matrix convention where the shared resistance is subtracted. If you define the source polarities differently, the signs change accordingly.

Worked Example

Using the default values from the calculator: R11 = 10 Ω, R12 = 20 Ω, R22 = 30 Ω, V1 = 12 V, V2 = 6 V.

Step 1: Write the matrix equation.

[ 10 -20 ] [ I1 ] [ 12 ]
[ -20 30 ] [ I2 ] = [ 6 ]

Step 2: Compute the determinant Δ = R11·R22 – R12² = 10×30 – 400 = 300 – 400 = -100.

Step 3: Solve for I1.

I1 = (V1·R22 – V2·R12) / Δ = (12×30 – 6×20) / (-100) = (360 – 120) / (-100) = 240 / (-100) = -2.40 A

Step 4: Solve for I2.

I2 = (R11·V2 – R12·V1) / Δ = (10×6 – 20×12) / (-100) = (60 – 240) / (-100) = (-180) / (-100) = 1.80 A

The calculator shows I1 = -2.400 A and I2 = 1.800 A. The negative sign on I1 means the actual current flows opposite to the assumed mesh direction.

Assumptions

  • The circuit is planar – no wires cross without a junction.
  • All resistances are linear and constant (Ohm’s law holds).
  • Voltage sources are ideal (zero internal resistance).
  • Current sources, if present, must be converted to equivalent voltage sources or handled with the supermesh technique – this calculator does not include them.
  • Mesh currents are defined in the same direction (usually clockwise) for all meshes.

When to Use Mesh Current Analysis

Mesh analysis is most efficient when a circuit has fewer independent loops than nodes. For a circuit with b branches and n nodes, the number of mesh equations equals b – n + 1. If that number is smaller than the number of node equations (n – 1), mesh analysis saves work. For example, a circuit with 6 branches and 4 nodes has 3 mesh equations but only 3 node equations – either works. But a circuit with many parallel branches and few loops is ideal for mesh analysis.

Mesh analysis is particularly useful for circuits with multiple voltage sources and resistors arranged in loops, such as bridge circuits, ladder networks, or circuits with dependent sources (though dependent sources require extra equations). It is the standard method taught in introductory circuit analysis courses.

How to Set Up the Equations by Hand

  1. Identify all meshes – the smallest closed loops that do not contain any other loop.
  2. Assign a clockwise current to each mesh (I1, I2, …).
  3. For each mesh, write KVL: sum of voltage drops across resistors = sum of voltage rises from sources. The voltage drop across a resistor is R·(mesh current) minus R·(adjacent mesh current) if the adjacent mesh shares that resistor.
  4. Collect like terms to form the matrix equation.
  5. Solve using Cramer’s rule, matrix inversion, or Gaussian elimination.

For a two-mesh circuit, the equations are:

Mesh 1: (R1 + R2)·I1 – R2·I2 = V1
Mesh 2: -R2·I1 + (R2 + R3)·I2 = V2

In the calculator, R11 = R1 + R2, R22 = R2 + R3, and R12 = R2. The default values correspond to R1 = 10 Ω, R2 = 20 Ω, R3 = 30 Ω, with V1 = 12 V and V2 = 6 V.

Common Mistakes and How to Avoid Them

  • Sign errors on the shared resistor: The shared resistor always appears with a negative sign in the matrix because the two mesh currents flow in opposite directions through it. Forgetting this sign flips the result.
  • Source polarity: A voltage source is positive if it pushes current in the direction of the mesh current. If you define the mesh current clockwise, a source with its positive terminal at the top of the left branch is positive for that mesh. Always mark the assumed current direction and source polarity before writing equations.
  • Unit mix-ups: Keep resistances in ohms, voltages in volts, and currents in amperes. If you use milliohms or millivolts, convert them first. The calculator expects ohms and volts.
  • Non-planar circuits: Mesh analysis only works on planar circuits – those that can be drawn on a flat plane without crossing wires. For non-planar circuits, use nodal analysis or loop analysis with a different approach.
  • Current sources: A current source in a mesh forces that mesh current to equal the source value. You cannot simply include it as a voltage source. Use the supermesh technique: combine meshes that share a current source into a single larger mesh.
  • Rounding too early: When solving by hand, keep at least three significant figures until the final step. Rounding intermediate values can shift the final current by several percent.

What the Results Mean

The mesh currents are not necessarily the same as branch currents. A branch that is not shared by two meshes carries exactly the mesh current that flows through it. A shared branch (like R2 in the example) carries the algebraic sum of the two mesh currents: I_branch = I1 – I2. In the worked example, I1 = -2.40 A and I2 = 1.80 A, so the current through R2 (from top to bottom) is I1 – I2 = -2.40 – 1.80 = -4.20 A, meaning it actually flows upward. The voltage across any resistor is then found by Ohm’s law: V = I·R.

If a mesh current comes out negative, it simply means the actual current flows opposite to the assumed direction. That is perfectly normal – the magnitude is correct, and the sign tells you the direction.

Limitations of the Calculator

This calculator handles two meshes only, which covers a large class of homework and design problems. For circuits with three or more meshes, you need a more general matrix solver. Also, the calculator assumes ideal voltage sources and linear resistors. Real sources have internal resistance, and resistors can change value with temperature – but for most textbook problems those effects are negligible.

For circuits with dependent sources (voltage or current controlled), you must add auxiliary equations that relate the control variable to the mesh currents. That is beyond what this simple calculator does, but the method still applies – you just have more equations.

Frequently Asked Questions

Can I use mesh analysis for a circuit with a current source? Yes, but you need the supermesh technique. Combine the two meshes that share the current source into one larger mesh that excludes the current source, write KVL for that supermesh, and add a constraint equation that the difference of the two mesh currents equals the source current. The calculator here does not handle that case automatically.

What is the difference between mesh and nodal analysis? Mesh analysis uses KVL around loops and solves for currents; nodal analysis uses KCL at nodes and solves for voltages. Mesh analysis is easier when the circuit has fewer loops than nodes, while nodal analysis is better when there are fewer nodes than loops. They give the same final answers – it is a matter of convenience.

Why do I get a negative current? A negative mesh current simply means the actual current flows in the opposite direction to the arrow you drew. The magnitude is still correct. In the worked example, I1 = -2.40 A means the current in mesh 1 actually flows counterclockwise, not clockwise as assumed.

Can this calculator handle more than two meshes? No, it is limited to two meshes. For three or more meshes, you would need to solve a larger matrix. Many online tools and software packages (like SPICE) can handle arbitrary circuits, but for a quick two-loop check, this works.

What if my circuit has a resistor that is not shared between meshes? That is fine. A resistor that belongs only to mesh 1 appears only in R11, not in R12. The method still works exactly the same way.

Do I need to convert units before using the calculator? Yes, enter resistances in ohms and voltages in volts. If your circuit has kilo-ohms, multiply by 1000 first. If you have millivolts, divide by 1000. The calculator gives currents in amperes.

Safety and Accuracy Notes

This calculator is for educational and design planning purposes only. Always verify your results with a physical measurement or a reliable simulation before building a circuit. When working with real circuits, follow your lab safety guidelines, use the correct rated components, and never exceed voltage or current ratings. For high-voltage or high-power circuits, consult a qualified engineer.

Related

Formula used
in m | Number of meshes | - | 2 | 0 | 10
in r11 | R1 (ohm) | ohm | 10 | 0 | 1000000
in r12 | R2 (ohm) | ohm | 20 | 0 | 1000000
in r22 | R3 (ohm) | ohm | 30 | 0 | 1000000
in v1 | V1 (volt) | V | 12 | -1000 | 1000
in v2 | V2 (volt) | V | 6 | -1000 | 1000
out i1 | Mesh current I1 | A | (v1*r22 - v2*r12) / (r11*r22 - r12*r12) | 3
out i2 | Mesh current I2 | A | (r11*v2 - r12*v1) / (r11*r22 - r12*r12) | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →