molecalculator

Moles & Molar Mass

mH to H Converter: Millihenry to Henry

Calculator No. 01-11624 · Updated · Formula and assumptions shown below

Inductance in henries (H) 0.0100 H
Inductance in microhenries (µH)
10,000.00 µH
= Inductance in millihenries (mH) × 1000
Inductance in millihenries (mH)
10 mH
Set in the form below
You enter
Inductance in millihenries (mH) (mH)
You get
Inductance in henries (H) (H), Inductance in microhenries (µH) (µH)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts inductance values from millihenries (mH) to henries (H) and back. You enter the inductance in millihenries, and it returns the equivalent in henries, plus the value in microhenries (µH) for convenience. The conversion is a simple division by 1000, since 1 henry equals 1000 millihenries.

Formula

The conversion between henries and millihenries is defined by the metric prefix milli-, meaning one-thousandth. The formula is:

H = mH / 1000

Where:

  • H is the inductance in henries (H)
  • mH is the inductance in millihenries (mH)
  • 1000 is the conversion factor (1 H = 1000 mH)

To convert the other way, multiply by 1000: mH = H × 1000.

Worked Example

Using the default value of 10 mH:

  1. Start with 10 mH.
  2. Divide by 1000: 10 / 1000 = 0.01 H.
  3. The calculator also shows 10 mH × 1000 = 10000 µH.

So 10 mH equals 0.01 H (or 10,000 µH). The calculator’s first output shows 0.0100 H, matching this result.

Assumptions

  • The conversion is exact and based on the definition of the metric prefix.
  • The value entered is a positive inductance (0 or greater).
  • No physical assumptions about the inductor (core material, frequency, etc.) are made.

Why Convert mH to H?

Inductance values in real circuits span a huge range. Small RF inductors are often in the nanohenry (nH) range, while power supply chokes can be in the henry range. The millihenry is a common middle ground, used for:

  • Transformers and motor windings (often tens to hundreds of mH)
  • Audio crossover inductors (typically 1–10 mH)
  • Filter inductors in power supplies (often 1–100 mH)

When you need to plug a value into a formula that expects henries (like the resonant frequency equation f = 1 / (2π√(LC))), you must convert from mH to H first. Forgetting this conversion is a common source of error—using 10 mH as 10 H in the resonant frequency formula would give a result 31.6 times too low (since √1000 ≈ 31.6).

How to Choose the Right Unit

To decide whether to work in mH or H, look at the magnitude of the value:

  • If the inductance is less than 0.001 H, use µH or nH.
  • If the inductance is between 0.001 H and 1 H, mH is convenient.
  • If the inductance is 1 H or more, use H directly.

In practice, most formulas in physics and engineering textbooks use the base unit (henry), so converting to H before calculation is safest. This calculator does that for you.

Common Mistakes and Misconceptions

Mistake 1: Confusing mH with µH. A millihenry is 1000 times larger than a microhenry. 1 mH = 1000 µH. Mixing these up changes your result by a factor of 1000.

Mistake 2: Forgetting to convert in formulas. Many inductance formulas (such as for resonant frequency, inductive reactance, or time constants) require the inductance in henries. If you plug in millihenries without converting, your answer will be off by orders of magnitude.

Mistake 3: Rounding too early. When converting 1 mH to 0.001 H, keep the full precision until the final step of your calculation. Rounding to 0.00 H would lose all information.

Misconception: “mH” means “megahenry”. In SI, the prefix “m” is lowercase and means milli (10⁻³). The prefix for mega is “M” (uppercase). So “mH” is millihenry, while “MH” would be megahenry (though that unit is rarely used). Always check the case.

Practical Examples

Here are a few real-world values you might encounter:

  • A typical audio crossover inductor: 2.2 mH = 0.0022 H.
  • A power supply filter choke: 50 mH = 0.05 H.
  • A small transformer primary: 500 mH = 0.5 H.

If you are designing a resonant circuit with a 10 mH inductor and a 100 nF capacitor, the resonant frequency is:

f = 1 / (2π√(0.01 H × 100 × 10⁻⁹ F)) ≈ 5033 Hz.

If you mistakenly used 10 H instead of 0.01 H, you would get ≈ 159 Hz—a huge difference.

Frequently Asked Questions

Q: How many henries are in a millihenry?
A: One millihenry is one-thousandth of a henry. So 1 mH = 0.001 H. To convert, divide the number of millihenries by 1000.

Q: What is the difference between mH and µH?
A: The prefix “m” (milli) means 10⁻³, and “µ” (micro) means 10⁻⁶. So 1 mH = 1000 µH. A millihenry is 1000 times larger than a microhenry.

Q: Can I convert henries to millihenries with this calculator?
A: Yes, you can. Enter the value in henries into the “Inductance in millihenries” field? No—that field expects mH. To convert from H to mH, multiply the H value by 1000. For example, 0.5 H × 1000 = 500 mH. You can use the calculator by entering 500 in the mH field to see it equals 0.5 H.

Q: Why do some inductors have values in henries while others use millihenries?
A: It’s a matter of convenience. Large inductors (like those in power supplies) may have values in the henry range, while smaller ones (like audio filters) are often in the millihenry range. Using the appropriate prefix keeps the numbers manageable—avoiding very small decimals or very large numbers.

Q: Does the conversion change with frequency or current?
A: No. The conversion between mH and H is a pure unit conversion, independent of frequency, current, or any physical condition. It is always a factor of 1000.

Q: What is the symbol for henry?
A: The symbol for henry is “H” (uppercase). The unit is named after Joseph Henry. The millihenry symbol is “mH” (lowercase m, uppercase H).

Limitations and Notes

This calculator only performs the unit conversion. It does not account for the tolerance of an inductor (usually ±10% or ±20%), nor does it model parasitic effects like series resistance or capacitance. For circuit design, always check the actual component’s datasheet or measure it with an LCR meter.

When working with inductance in formulas, always ensure you use the base unit (henry) unless the formula explicitly states otherwise. This calculator helps you do that quickly and accurately.

Related

Formula used
in mh | Inductance in millihenries (mH) | mH | 10 | 0 | 1000000
out h | Inductance in henries (H) | H | mh / 1000 | 4
out uh | Inductance in microhenries (µH) | µH | mh * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →