molecalculator

Moles & Molar Mass

Mix Air Temp Calculator: How to Find Final Temperature

Calculator No. 01-7978 · Updated · Formula and assumptions shown below

Final mixture temperature 60.00 °C
Mass ratio (stream 1:stream 2)
0.500
= Mass of stream 1 ÷ Mass of stream 2
Mass of stream 1
1 kg
Set in the form below
Temperature of stream 1
20 °C
Set in the form below
You enter
Mass of stream 1 (kg), Temperature of stream 1 (°C), Mass of stream 2 (kg), Temperature of stream 2 (°C)
You get
Final mixture temperature (°C), Mass ratio (stream 1:stream 2)
Rounding
2 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A mix air temperature calculator determines the final temperature when two or more air streams at different temperatures are combined, assuming no heat is lost to the surroundings. You enter the mass (or volume) and temperature of each air stream, and the calculator returns the equilibrium temperature of the mixture. This is a straightforward application of the principle of conservation of energy, and the result is a weighted average of the initial temperatures.

Formula

The calculation uses the principle that the heat lost by the warmer stream equals the heat gained by the cooler stream, assuming no heat exchange with the environment. For two streams, the formula is:

Tmix = (m₁·T₁ + m₂·T₂) / (m₁ + m₂)

  • Tmix – final temperature of the mixture (°C or K, as long as both temperatures use the same scale)
  • m₁, m₂ – masses of the two air streams (kg, g, or any consistent unit)
  • T₁, T₂ – initial temperatures of the two streams (°C or K)

This is a weighted average: each temperature is weighted by the mass of the stream at that temperature. The same formula extends to three or more streams by adding more m·T terms in the numerator and more masses in the denominator.

Worked Example

Using the default values from the calculator: stream 1 has mass 1.0 kg at 20 °C, and stream 2 has mass 2.0 kg at 80 °C.

  1. Multiply each mass by its temperature: 1.0 × 20 = 20; 2.0 × 80 = 160.
  2. Add those products: 20 + 160 = 180.
  3. Add the masses: 1.0 + 2.0 = 3.0 kg.
  4. Divide the sum of products by the total mass: 180 / 3.0 = 60 °C.

The calculator returns 60.00 °C, which matches the hand calculation. Notice that the final temperature is closer to 80 °C than to 20 °C because there is twice as much mass at the higher temperature.

Assumptions

  • No heat is lost to the surroundings (adiabatic mixing).
  • The specific heat capacity of air is constant and the same for both streams (true for air over modest temperature ranges).
  • No phase change occurs (no condensation or evaporation).
  • The mixing is complete and instantaneous, so the final temperature is uniform.
  • Pressure is constant; this does not affect the calculation because we use mass, not volume.

When to Use This Calculator

This calculator is useful in HVAC design, ventilation planning, and industrial process engineering. For example, an engineer might need to know the temperature of mixed return air and fresh outdoor air before it enters a heating or cooling coil. Similarly, a lab technician mixing two air streams from different sources can quickly estimate the resulting temperature. It also applies to mixing any gases, not just air, as long as the specific heat capacities are similar and no chemical reaction occurs.

For more than two streams, you can extend the formula by adding each stream’s mass-temperature product to the numerator and each mass to the denominator. The calculator handles two streams, but the logic is identical for any number.

Common Mistakes and How to Avoid Them

  • Using volume instead of mass – Air density changes with temperature, so equal volumes of hot and cold air do not contain equal masses. Always convert volumes to masses using the density at each stream’s temperature, or use mass flow rates if the streams are moving.
  • Mixing temperature scales – You can use °C or K, but not both in the same calculation. The difference is a constant offset (K = °C + 273.15), which cancels out in the weighted average, so the result in °C is the same whether you use °C or K, as long as you are consistent.
  • Forgetting that the result is a weighted average – A common intuition error is to average the temperatures directly (e.g., (20+80)/2 = 50 °C), which is only correct if both masses are equal. With unequal masses, the larger stream dominates the final temperature.
  • Ignoring heat loss – In real-world ducts, some heat is lost to the surroundings, especially if the duct is long or uninsulated. The calculator gives the theoretical maximum mixing temperature; actual values will be slightly lower.

How to Choose the Right Inputs

The calculator requires mass, but you often have volume or volumetric flow rate. To convert volume to mass, multiply by the density of air at that temperature. At 20 °C and 1 atm, dry air density is about 1.204 kg/m³; at 80 °C, it is about 0.999 kg/m³. If you have volumetric flow rates (e.g., m³/s), multiply each by its density to get mass flow rate, then use those in the calculator.

For most HVAC applications, using mass flow rates is standard because they are conserved regardless of temperature. If you only need a rough estimate, you can assume constant density, but be aware that the error grows with larger temperature differences.

Limitations of the Formula

The formula assumes constant specific heat capacity. For air, this is a good approximation over a range of roughly -50 °C to 200 °C, where the specific heat varies by less than 1%. Outside that range, you would need to integrate the heat capacity over temperature. The formula also assumes no moisture condensation. If the air is humid and mixing causes the temperature to drop below the dew point, water will condense, releasing latent heat and making the final temperature higher than the simple weighted average. For accurate results in humid conditions, use a psychrometric chart or a more advanced model.

Frequently Asked Questions

Does the final temperature depend on the specific heat of air?

No, as long as both streams have the same specific heat capacity. The specific heat cancels out of the energy balance equation. If you were mixing different gases (e.g., air and helium), you would need to include their individual specific heats. For air-air mixing, the formula is independent of the actual value.

Can I use this for liquids or other gases?

Yes, the same weighted-average formula applies to any two substances with the same specific heat capacity. For different substances, you must use the full energy balance: m₁·c₁·T₁ + m₂·c₂·T₂ = (m₁·c₁ + m₂·c₂)·Tmix. This calculator is for air, but the principle is universal.

What if I have three air streams?

Extend the formula: Tmix = (m₁T₁ + m₂T₂ + m₃T₃) / (m₁ + m₂ + m₃). Add as many terms as you have streams. The calculator only handles two, but you can do the arithmetic manually or combine streams stepwise.

Does pressure affect the result?

No, as long as the pressure is the same for both streams. Pressure affects density, which you use to convert volume to mass, but once you have masses, the mixing temperature is independent of pressure. If the streams are at different pressures, you must account for that when determining mass, but the formula itself remains valid.

Why is the result not simply the average of the two temperatures?

Because the average (arithmetic mean) assumes equal masses. The correct result is a mass-weighted average. If one stream has more mass, it “pulls” the final temperature closer to its own temperature. For equal masses, the result equals the arithmetic average.

What if the temperatures are in Fahrenheit?

You can convert to °C first (or use the formula directly with °F, but the result will be in °F). The weighted average works in any linear temperature scale. However, be careful with absolute scales like Rankine: the result will be in Rankine, which you can convert back to °F by subtracting 459.67.

Related

Formula used
in m1 | Mass of stream 1 | kg | 1.0 | 0
in t1 | Temperature of stream 1 | °C | 20 | -273.15
in m2 | Mass of stream 2 | kg | 2.0 | 0
in t2 | Temperature of stream 2 | °C | 80 | -273.15
out tmix | Final mixture temperature | °C | (m1 * t1 + m2 * t2) / (m1 + m2) | 2
out ratio | Mass ratio (stream 1:stream 2) | - | m1 / m2 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →