molecalculator

Moles & Molar Mass

Mixed Air Formula for HVAC Systems

Calculator No. 01-7979 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The mixed air formula calculates the temperature of air after two or more airstreams combine in an HVAC system, most commonly return air and outdoor ventilation air. You enter the temperature and airflow rate of each stream, and the calculator gives the resulting mixed air temperature, which is used to size cooling and heating coils. The formula is a flow-weighted average: T_mixed = (T_1 × Q_1 + T_2 × Q_2) / (Q_1 + Q_2).

Formula

The mixed air temperature is the weighted average of the individual airstream temperatures, weighted by their volumetric flow rates:

Tmixed = (T1 × Q1 + T2 × Q2) / (Q1 + Q2)

Where:

  • T1 = temperature of airstream 1 (e.g., return air), in °C
  • Q1 = volumetric flow rate of airstream 1, in m³/s (or any consistent unit)
  • T2 = temperature of airstream 2 (e.g., outdoor air), in °C
  • Q2 = volumetric flow rate of airstream 2, in m³/s

The formula assumes constant air density and specific heat, which is reasonable for typical HVAC temperature ranges (0–50 °C). For more than two streams, extend the pattern: sum of (T × Q) for all streams divided by the sum of all Q.

Worked Example

Using the calculator defaults: return air at 24 °C with a flow of 1.2 m³/s, outdoor air at 35 °C with a flow of 0.3 m³/s.

Step 1: Multiply each temperature by its flow rate:

  • Return: 24 × 1.2 = 28.8 °C·m³/s
  • Outdoor: 35 × 0.3 = 10.5 °C·m³/s

Step 2: Add these products: 28.8 + 10.5 = 39.3 °C·m³/s

Step 3: Add the flow rates: 1.2 + 0.3 = 1.5 m³/s

Step 4: Divide: 39.3 / 1.5 = 26.2 °C

The mixed air temperature is 26.2 °C, which matches the calculator output.

Assumptions

  • Air density is constant across all streams (no altitude correction).
  • Specific heat of air is constant (valid for typical HVAC temperatures).
  • No heat gain or loss in the mixing plenum or ductwork.
  • Flow rates are volumetric and measured at the same conditions.
  • Complete mixing occurs before the temperature is measured.

Why the Mixed Air Formula Matters

HVAC systems almost never use 100% outdoor air because it would be too expensive to heat or cool. Instead, they mix a small amount of fresh outdoor air (for ventilation) with a larger volume of return air from the building. The temperature of this mixed air is what the cooling coil or heating coil actually sees. If you size the coil based on outdoor air temperature alone, you will oversize the equipment; if you use return air temperature alone, you will undersize it. The mixed air temperature gives the correct design load.

For example, in summer, outdoor air at 35 °C mixes with return air at 24 °C. The coil must cool the mixture down to the supply air temperature (typically 12–14 °C). The mixed air temperature determines the coil’s entering air condition, which affects both sensible and latent cooling loads.

How to Use the Calculator for Real Systems

To use the formula in practice, you need two pieces of data for each airstream: temperature and flow rate. Here is how to get them:

  • Return air temperature: measure at the return grille or in the return duct before the mixing point. Use a calibrated thermometer or temperature sensor.
  • Outdoor air temperature: for design, use the local climate data (e.g., 1% cooling design temperature). For real-time, measure at the outdoor air intake.
  • Return air flow: typically the supply fan flow minus the outdoor air flow. You can measure with a pitot tube traverse or use the building’s balancing report.
  • Outdoor air flow: measure at the outdoor air intake with an anemometer or flow hood, or calculate from the damper position and duct size.

If you only know the percentage of outdoor air (e.g., 20%), you can use that fraction directly: T_mixed = (1 – f) × T_return + f × T_outdoor, where f is the outdoor air fraction. For example, with 20% outdoor air at 35 °C and return at 24 °C: T_mixed = 0.8 × 24 + 0.2 × 35 = 19.2 + 7.0 = 26.2 °C, the same result as the flow-weighted calculation.

Common Mistakes and Misconceptions

  • Using temperatures in Fahrenheit without converting: The formula works with any consistent temperature scale, but if you mix °F and °C, you get nonsense. Always use the same unit.
  • Forgetting that flow rates must be in the same unit: You can use L/s, m³/s, or CFM, but all streams must be in the same unit. The calculator uses m³/s, but you can convert CFM to m³/s by multiplying by 0.000471947.
  • Assuming the mixed temperature is the average of the two temperatures: Only true if the flow rates are equal. In most systems, return air flow is much larger, so the mixed temperature is closer to the return temperature.
  • Ignoring humidity: The formula gives the dry-bulb temperature only. For coil sizing, you also need the mixed air humidity ratio or wet-bulb temperature, which requires a psychrometric calculation. The dry-bulb mixed temperature is still the starting point.
  • Using the formula for supply air after the coil: The mixed air formula applies only to the mixing of airstreams before conditioning. After the coil, the temperature is determined by the coil’s performance, not mixing.

Practical Variations: More Than Two Streams

Some systems mix three or more airstreams, such as return air, outdoor air, and exhaust air transfer. The formula extends naturally:

Tmixed = (T1Q1 + T2Q2 + T3Q3) / (Q1 + Q2 + Q3)

For example, if you add a third stream at 20 °C with 0.1 m³/s to the previous example, the mixed temperature becomes (28.8 + 10.5 + 2.0) / (1.2 + 0.3 + 0.1) = 41.3 / 1.6 = 25.8 °C. The calculator above handles two streams; for more, you can combine them stepwise (mix two, then mix the result with the third).

Limits of the Formula

The mixed air formula is a steady-state energy balance that ignores kinetic and potential energy changes, which are negligible in HVAC ducts. It also assumes no heat transfer through duct walls, which is a good approximation for insulated ducts but less accurate for long uninsulated runs. For extreme temperature differences (e.g., outdoor air at -40 °C), the density change can cause slight errors, but for standard HVAC design, the error is under 1 °C. For precise work, use the enthalpy method (mixing enthalpy, not temperature), which accounts for humidity and density variations. However, for most preliminary sizing and troubleshooting, the temperature-only formula is sufficient.

Frequently Asked Questions

What is the mixed air formula for HVAC? The formula is T_mixed = (T1×Q1 + T2×Q2) / (Q1 + Q2), where T is temperature and Q is volumetric flow rate for each airstream. It gives the dry-bulb temperature of the combined air.

Why do I need to calculate mixed air temperature? Because the cooling or heating coil sees the mixed air, not the outdoor air or return air alone. Using the wrong entering temperature leads to incorrect coil sizing, which causes poor comfort and wasted energy.

Can I use the formula with CFM and Fahrenheit? Yes, as long as you use the same units for both streams. For example, T in °F and Q in CFM works fine. The result will be in °F. Just do not mix units.

What is a typical mixed air temperature in summer? In a commercial building with 20% outdoor air at 35 °C and return air at 24 °C, the mixed temperature is about 26.2 °C. The exact value depends on the outdoor air fraction and return air temperature.

Does the mixed air formula account for humidity? No, it only gives dry-bulb temperature. For coil load calculations, you also need the mixed air humidity ratio or wet-bulb temperature, which requires a psychrometric chart or calculation.

What if I have more than two airstreams? Extend the formula: sum of (T×Q) for all streams, divided by the sum of all Q. The calculator here handles two, but you can combine streams sequentially.

Related

Formula used
in t1 | Return air temperature | °C | 24 | -273.15
in q1 | Return air flow | m³/s | 1.2 | 0
in t2 | Outdoor air temperature | °C | 35 | -273.15
in q2 | Outdoor air flow | m³/s | 0.3 | 0
out tm | Mixed air temperature | °C | (t1 * q1 + t2 * q2) / (q1 + q2) | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →