The mixed air formula for HVAC calculates the temperature of air after two or more airstreams combine, typically return air and outdoor ventilation air. You enter the temperatures and airflow rates (in CFM or L/s) of each stream, and the calculator returns the resulting mixed air dry-bulb temperature. This value is essential for sizing cooling coils, predicting coil loads, and ensuring proper ventilation without over-conditioning.
Formula
The mixed air temperature is a flow-weighted average of the individual stream temperatures. For two streams, the formula is:
Tmixed = (Treturn × Qreturn + Toutdoor × Qoutdoor) / (Qreturn + Qoutdoor)
Where:
- Treturn = temperature of return air (°F or °C)
- Qreturn = volumetric flow rate of return air (CFM or L/s)
- Toutdoor = temperature of outdoor air (°F or °C)
- Qoutdoor = volumetric flow rate of outdoor air (CFM or L/s)
For more than two streams, extend the numerator and denominator accordingly. The formula assumes the specific heat and density of the air streams are equal, which is a standard approximation for HVAC design.
Worked Example
Using the default values from the calculator: return air at 72°F with 1200 CFM, outdoor air at 95°F with 300 CFM.
- Multiply return temperature by return flow: 72 × 1200 = 86,400
- Multiply outdoor temperature by outdoor flow: 95 × 300 = 28,500
- Add the products: 86,400 + 28,500 = 114,900
- Add the flow rates: 1200 + 300 = 1500 CFM
- Divide: 114,900 / 1500 = 76.6°F
The mixed air temperature is approximately 76.6°F, matching the calculator’s output. The outdoor air fraction is 300 / 1500 = 20%.
Assumptions
- Air density is constant across streams (standard air density).
- Specific heat of air is constant.
- No heat gain or loss in the mixing plenum.
- Streams mix completely and adiabatically.
- Dry-bulb temperatures are used; latent heat (moisture) is ignored for this simple calculation.
Why Mixed Air Temperature Matters
HVAC systems often mix return air with outdoor ventilation air to maintain indoor air quality while saving energy. The mixed air temperature directly affects:
- Cooling coil sizing: A warmer mixed air stream requires a larger coil or more chilled water flow.
- Heating coil sizing: In winter, mixing cold outdoor air with warm return air reduces the heating load.
- Economizer operation: When outdoor air is cool and dry, it can be used for free cooling; the mixed air temperature helps decide when to switch.
- Supply air temperature control: The mixed air temperature is the starting point for the coil leaving air temperature.
For example, if the design outdoor temperature is 95°F and the return is 72°F, a 20% outdoor air fraction yields a mixed air temperature of 76.6°F, not the 95°F outdoor temperature. This is why the coil sees a much lower load than if 100% outdoor air were used.
How to Choose Outdoor Air Flow Rate
The outdoor air flow rate is not arbitrary; it is set by ventilation codes (like ASHRAE 62.1) and building occupancy. Common methods:
- Ventilation rate procedure: Calculate based on floor area and expected occupants, using prescribed per-person and per-area rates.
- Indoor air quality procedure: Use contaminant concentration limits to determine required outdoor air.
- Natural ventilation: If windows are operable, the system may reduce mechanical outdoor air, but the mixed air calculation still applies when fans run.
Once the required outdoor air flow is known, you can use the calculator to see the resulting mixed air temperature for worst-case summer and winter conditions. This helps select the coil and preheat equipment.
Common Mistakes and Misconceptions
One common error is using the average of temperatures without weighting by flow. For example, averaging 72°F and 95°F gives 83.5°F, but the correct answer is 76.6°F because the return air flow is much larger. Another mistake is mixing units: if one flow is in CFM and the other in L/s, the formula will be wrong. Always convert to the same unit first (1 CFM = 0.4719 L/s).
Also, the formula gives the dry-bulb temperature. It does not account for humidity. In humid climates, the enthalpy (total heat) of the mixed air is often more important for coil load, but the dry-bulb temperature is a useful first approximation. For accurate coil sizing, use a psychrometric chart or software that accounts for moisture.
Finally, the outdoor air fraction is not the same as the damper position. Dampers are often nonlinear, so a 20% open damper may not deliver 20% outdoor air. The fraction should be measured with an airflow hood or anemometer.
Comparisons: Mixed Air vs. 100% Outdoor Air
In mild weather, an economizer can use 100% outdoor air for free cooling, bypassing the return air. In that case, the mixed air temperature equals the outdoor air temperature. The calculator still works if you set the return flow to zero. In extreme weather, using 100% outdoor air would require huge coils, so mixing with return air is standard. The trade-off is between indoor air quality (more outdoor air) and energy efficiency (less outdoor air). The mixed air temperature is the key metric to balance these.
Cost and Energy Implications
Lower mixed air temperatures in summer reduce cooling energy. For a given coil, a 1°F reduction in mixed air temperature can cut cooling energy by roughly 2-3%. Conversely, in winter, a higher mixed air temperature reduces heating energy. The calculator helps estimate these savings. For example, if the outdoor air fraction is 20%, the mixed air temperature is much closer to the return temperature, so the coil doesn’t have to work as hard. However, minimum outdoor air must still be maintained for ventilation, so you can’t simply reduce it to zero.
Safety and Practical Considerations
When measuring temperatures, use calibrated sensors. Place the temperature sensor in a location where mixing is complete, typically several duct diameters downstream of the mixing point. Avoid measuring near the dampers where stratification occurs. For large systems, consider using multiple sensors and averaging. Also, follow your local building codes and the equipment manufacturer’s guidelines for ventilation rates. The mixed air temperature is a design tool, not a safety device; ensure your system has proper freeze protection if outdoor air can drop below 32°F.
Frequently Asked Questions
What is the mixed air formula for three or more airstreams?
Extend the weighted average: multiply each stream’s temperature by its flow, sum all products, then divide by the total flow. For example, with three streams, T_mixed = (T1×Q1 + T2×Q2 + T3×Q3) / (Q1+Q2+Q3). The same principle applies to any number of streams.
Can I use this formula for Celsius and L/s?
Yes, the formula is unit-agnostic as long as you are consistent. Use °C for all temperatures and L/s for all flows. The calculator above uses °F and CFM, but you can convert inputs or use the same formula with your units.
Does the mixed air temperature affect humidity?
The dry-bulb temperature alone does not determine humidity. The mixed air humidity ratio (moisture content) is a flow-weighted average of the humidity ratios of the streams. For coil load calculations, you need both temperature and humidity. Use a psychrometric chart to find the enthalpy of the mixed air.
What is the typical outdoor air fraction for commercial buildings?
It varies, but 10-20% of total supply air is common for offices. ASHRAE 62.1 specifies minimum ventilation rates based on occupancy and floor area. For example, an office might need 5 CFM per person plus 0.06 CFM per square foot. The actual fraction depends on the total supply airflow.
Why is my measured mixed air temperature different from the calculated one?
Possible reasons: incomplete mixing (stratification), heat gain from ductwork, sensor inaccuracy, or inaccurate flow measurements. Also, damper leakage can allow more outdoor air than intended. Use a traversing probe to measure temperature and flow accurately.
Can I use this for residential HVAC?
Yes, but residential systems often have little or no mechanical ventilation. If you have an HRV/ERV or a fresh air intake, this formula applies. For a typical house with a 200 CFM return and 50 CFM outdoor air at 95°F, mixed temperature would be (72×200 + 95×50)/250 = 76.6°F, similar to the example.
Related
Formula used
in v | Return air flow | CFM | 1200 | 0 in t | Return air temp | °F | 72 | -100 in vo | Outdoor air flow | CFM | 300 | 0 in to | Outdoor air temp | °F | 95 | -100 out tm | Mixed air temp | °F | (t * v + to * vo) / (v + vo) | 1 out frac | Outdoor air fraction | % | (vo / (v + vo)) * 100 | 1
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check