The mixed air temperature formula calculates the temperature of air after two or more airstreams combine, typically outdoor air and return air in an HVAC system. You enter the temperature and airflow (or mass flow) of each stream, and the calculator returns the resulting mixed air dry-bulb temperature. The formula is a flow-weighted average, meaning larger airstreams influence the final temperature more than smaller ones.
Formula
The mixed air temperature is a weighted arithmetic mean of the individual stream temperatures, weighted by their volumetric airflow rates:
Tmixed = (T1 × V1 + T2 × V2) / (V1 + V2)
Where:
- T1 = dry-bulb temperature of airstream 1 (°C or °F)
- V1 = volumetric airflow of airstream 1 (m³/s, L/s, or ft³/min)
- T2 = dry-bulb temperature of airstream 2 (°C or °F)
- V2 = volumetric airflow of airstream 2 (same unit as V1)
The same equation extends to three or more streams: sum of (temperature × flow) for each stream, divided by the total flow. The key requirement is that all temperatures use the same scale and all flows use the same unit. The formula assumes no heat is added or removed during mixing, no moisture condenses, and the air streams are at the same pressure.
Worked Example
Using the calculator defaults: outdoor air at 35 °C with 2.0 m³/s flow mixes with return air at 22 °C with 1.0 m³/s flow.
Step 1: Multiply each temperature by its flow.
Stream 1: 35 °C × 2.0 m³/s = 70.0 °C·m³/s
Stream 2: 22 °C × 1.0 m³/s = 22.0 °C·m³/s
Step 2: Add the products.
70.0 + 22.0 = 92.0 °C·m³/s
Step 3: Add the flows.
2.0 + 1.0 = 3.0 m³/s
Step 4: Divide.
92.0 / 3.0 = 30.7 °C
The mixed air temperature is 30.7 °C, which is closer to the outdoor temperature because the outdoor stream has twice the airflow. The total mixed airflow is 3.0 m³/s.
Assumptions
- Adiabatic mixing: no heat transfer to or from the duct walls.
- Constant pressure: all streams are at the same static pressure.
- No phase change: no condensation or evaporation occurs during mixing.
- Constant density: air density is assumed equal across streams, which is reasonable for HVAC temperature ranges.
- Dry-bulb temperatures: the formula applies to sensible heat only, not latent heat (moisture content).
When to Use the Mixed Air Temperature Formula
HVAC engineers and technicians use this formula most often for economizer control, where outdoor air is mixed with return air to reduce cooling load. It also appears in:
- Duct system design, to size cooling coils that see mixed air rather than pure outdoor air.
- Ventilation calculations, to estimate the temperature of air entering an air handling unit.
- Energy modeling, to predict how much outdoor air raises or lowers supply temperature.
- Building commissioning, to verify that dampers and sensors are reading correctly.
The result tells you the sensible temperature of the combined airstream. If the two streams have very different humidity levels, the mixed air enthalpy (total heat) requires a psychrometric chart calculation, not just this dry-bulb formula. The dry-bulb temperature alone is still correct for the sensible component, but the wet-bulb temperature of the mixture is not a simple weighted average.
Common Mistakes and How to Avoid Them
The most frequent error is mixing units. If one flow is in m³/s and the other in L/s, the result is wrong. Convert all flows to the same unit before calculating. Similarly, temperatures must be all °C or all °F; never mix them.
Another common mistake is using velocity instead of volumetric flow. Two ducts can have the same air velocity but very different cross-sectional areas, giving different actual flow rates. The formula requires volumetric flow (volume per time), not speed.
A third issue is assuming the formula works for wet-bulb temperature. It does not. Wet-bulb temperature mixing requires accounting for latent heat, and the result is always lower than the arithmetic average of wet-bulb temperatures. Use a psychrometric chart or software for that calculation.
Finally, be careful with temperature scales that have an arbitrary zero. The formula is linear, so it works for both °C and °F, but it will not give correct results if you use °R or K in a formula designed for °F, unless you convert the final answer back. Since the formula is a ratio, using absolute temperatures (K or °R) produces a different numeric result that is the true thermodynamic mixed temperature in that scale; convert it to °C or °F afterward if needed.
How to Choose the Right Flow Measurement
For most HVAC mixing calculations, volumetric airflow in cubic feet per minute (CFM) or liters per second (L/s) is standard. The formula works identically regardless of which volumetric unit you choose, as long as both streams use the same unit. Mass flow (kg/s or lb/min) also works and is actually more physically correct when air densities differ significantly, such as when one stream is very hot and the other very cold.
In practice, most engineers use volumetric flow because duct traversals and anemometers report volume directly. If you have mass flow, the same weighted-average formula applies with mass flow replacing volumetric flow. The result will be nearly identical for typical HVAC temperature ranges because the density difference between 10 °C and 40 °C air is only about 10%.
When measuring airflow, ensure the measurement is taken at the same location in the duct each time, ideally on a straight section away from elbows and dampers. A pitot tube traverse or a thermal anemometer gives the most reliable readings. If you only have velocity and duct dimensions, multiply velocity by the cross-sectional area to get volumetric flow.
Limitations of the Formula
The mixed air temperature formula is a steady-state, adiabatic mixing model. It does not account for:
- Heat gain or loss through duct walls, which can be significant for long uninsulated runs.
- Fan heat, which adds energy to the air downstream of the mixing point.
- Moisture condensation, which releases latent heat and raises the dry-bulb temperature.
- Stratification, where streams do not fully mix before reaching the coil.
Stratification is a real problem in practice. If the outdoor air and return air enter at different points and the duct is short, the air may not be uniformly mixed when it hits the temperature sensor or cooling coil. This can cause the sensor to read mostly one stream, leading to incorrect control decisions. Mixing baffles or longer duct runs help, but the formula assumes perfect mixing.
For extreme temperature differences, the constant-density assumption introduces small errors. At 200 °C and 20 °C, the hot air is roughly half the density of the cold air, so a volumetric weighted average overestimates the influence of the hot stream. Using mass flow fixes this, but such high temperatures are rare in HVAC mixing applications.
Frequently Asked Questions
Does the mixed air temperature formula work for three or more airstreams?
Yes. Extend the formula by adding each stream’s temperature multiplied by its flow, then divide by the sum of all flows. For example, with three streams: (T1×V1 + T2×V2 + T3×V3) / (V1 + V2 + V3). The same unit consistency rules apply.
What is the difference between mixed air temperature and supply air temperature?
Mixed air temperature is measured right after outdoor and return air combine, before any heating or cooling. Supply air temperature is measured after the coil or furnace has conditioned the air. The mixed air temperature is the input to the coil; the supply air temperature is the output.
Why does my measured mixed air temperature differ from the calculated value?
Common causes are sensor placement in a stratified flow, inaccurate airflow measurements, duct heat gain, and fan heat. Check that the sensor is downstream of a mixing baffle or at least 5 duct diameters from the mixing point. Re-measure airflow with a calibrated instrument.
Can I use this formula for exhaust air mixing with supply air?
Yes, the formula is purely mathematical and applies to any two airstreams mixing at constant pressure. However, if the exhaust air contains contaminants or high humidity, you must consider air quality and latent heat, not just dry-bulb temperature.
Should I use volumetric or mass flow in the formula?
Either works for typical HVAC temperatures. Volumetric flow is easier to measure and standard in duct design. Mass flow is more accurate when stream temperatures differ by more than about 30 °C, because density changes become significant. For most economizer and ventilation calculations, volumetric flow is sufficient.
Does the formula give the wet-bulb mixed air temperature?
No. The formula gives only the dry-bulb temperature. The wet-bulb temperature of a mixture is not a weighted average because it depends on the moisture content of each stream. To find mixed wet-bulb temperature, plot both streams on a psychrometric chart and find the point that divides the connecting line in proportion to the flow ratio.
Practical Tips for HVAC Work
When using this formula in the field, always verify your airflow measurements. A simple pitot tube traverse across the duct diameter gives a much better average than a single point reading. For return air ducts with multiple branches, measure each branch and sum the flows. For outdoor air, measure at the intake louver if possible, where the flow is more uniform.
Calibrate temperature sensors regularly. A sensor reading 2 °C high on the outdoor air stream will shift the mixed air calculation noticeably, especially when outdoor airflow is large. Compare sensor readings against a calibrated reference thermometer at the same location.
If you are designing a system, use the mixed air temperature to size the cooling coil. The coil must handle the sensible load of the mixed air, not just the outdoor air. Oversizing based on outdoor air alone wastes energy; undersizing based on return air alone leads to comfort complaints. The weighted average gives the correct design point.
Finally, remember that the formula assumes perfect mixing. In real ducts, install a static mixer or at least a few elbows to promote turbulence before the sensor. If stratification persists, consider averaging multiple sensors across the duct cross-section and using their average as the mixed air temperature input to the controller.
Related
Formula used
in t1 | Temperature of stream 1 | °C | 35 | -273.15 | 200 in v1 | Airflow of stream 1 | m³/s | 2.0 | 0 | 1000 in t2 | Temperature of stream 2 | °C | 22 | -273.15 | 200 in v2 | Airflow of stream 2 | m³/s | 1.0 | 0 | 1000 out tm | Mixed air temperature | °C | (t1 * v1 + t2 * v2) / (v1 + v2) | 1 out vtot | Total mixed airflow | m³/s | v1 + v2 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check