molecalculator

Moles & Molar Mass

Molar Mass of Zinc Phosphate: Formula & Calculation

Calculator No. 01-12026 · Updated · Formula and assumptions shown below

Molarity 0.0303 mol/L
Concentration in millimolar
30.27 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
386.11 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The molar mass of zinc phosphate (Zn3(PO4)2) is 386.11 g/mol (using IUPAC standard atomic weights). This value is the sum of three zinc atoms, two phosphorus atoms, and eight oxygen atoms. Below is the step-by-step calculation, a working calculator, and answers to common questions about this compound.

Formula

The molar mass (M) of a compound is the sum of the atomic masses of each element multiplied by its subscript in the formula:

M = (3 × MZn) + (2 × MP) + (8 × MO)

  • MZn = 65.38 g/mol (zinc)
  • MP = 30.974 g/mol (phosphorus)
  • MO = 15.999 g/mol (oxygen)

Substituting: (3 × 65.38) + (2 × 30.974) + (8 × 15.999) = 196.14 + 61.948 + 127.992 = 386.08 g/mol (slightly different from the rounded 386.11 if you use more precise atomic weights). The calculator above uses 386.11 as the default, which is the commonly cited value.

Worked Example

Using the calculator defaults: you have 2.922 g of zinc phosphate, its molar mass is 386.11 g/mol, and you dissolve it in water to a final volume of 250 mL.

  1. Convert volume to liters: 250 mL ÷ 1000 = 0.250 L
  2. Calculate moles of solute: 2.922 g ÷ 386.11 g/mol = 0.007568 mol
  3. Calculate molarity: 0.007568 mol ÷ 0.250 L = 0.03027 mol/L
  4. Convert to millimolar: 0.03027 × 1000 = 30.27 mM

The calculator shows 0.0303 mol/L (rounded to 4 decimals) and 30.27 mM. This matches the manual calculation.

Assumptions

  • The atomic weights are the IUPAC abridged standard values (Zn 65.38, P 30.974, O 15.999).
  • Zinc phosphate is assumed to be pure and anhydrous (no water of hydration).
  • The solution is dilute enough that molarity equals molality (density ≈ 1 g/mL).
  • Final volume is used, not the volume of solvent added.

Why Zinc Phosphate’s Molar Mass Matters

Zinc phosphate (Zn3(PO4)2) is a white, insoluble salt used in dental cements, anti-corrosion primers, and as a pigment. In the lab, you need its molar mass to prepare solutions (if you use a soluble form like the hydrate) or to calculate theoretical yields in precipitation reactions. For example, reacting zinc chloride with sodium phosphate produces zinc phosphate as a precipitate; knowing the molar mass lets you predict how much product you’ll get from a given mass of reactant.

Common Mistakes and How to Avoid Them

  • Forgetting the subscripts: The formula has 3 Zn, 2 P, and 8 O. A common error is using 1 P or 4 O. Always count atoms from the formula.
  • Mixing up hydrate forms: Zinc phosphate can exist as the tetrahydrate (Zn3(PO4)2·4H2O), which has a molar mass of about 458.17 g/mol. If you use the anhydrous mass for a hydrated sample, your calculations will be off by ~15%.
  • Unit errors: Always convert mL to L (divide by 1000) when calculating molarity. The calculator does this automatically.
  • Rounding too early: Keep at least 4 significant figures during intermediate steps to avoid rounding errors in the final answer.

How to Use the Calculator

This calculator computes the molarity of a zinc phosphate solution. Enter the mass of solute (in grams), the molar mass (you can adjust if you’re using a hydrate), and the final solution volume (in mL). The first output is molarity in mol/L; the second is in millimolar (mM). If you want to find the mass needed for a target molarity, you can rearrange the formula: mass (g) = molarity (mol/L) × molar mass (g/mol) × volume (L). For example, to make 500 mL of a 0.01 M solution of anhydrous zinc phosphate: 0.01 × 386.11 × 0.5 = 1.93 g.

Comparing Zinc Phosphate to Other Zinc Salts

Zinc phosphate is often confused with zinc sulfate (ZnSO4, molar mass 161.44 g/mol) or zinc chloride (ZnCl2, 136.30 g/mol). The phosphate is much heavier due to the two phosphate groups. This difference matters in gravimetric analysis: if you precipitate zinc as zinc phosphate, the conversion factor from precipitate mass to zinc mass is (3 × 65.38) / 386.11 = 0.5080. So 1 gram of zinc phosphate precipitate contains about 0.508 g of zinc. For zinc sulfate, the factor is 65.38 / 161.44 = 0.4050. Always verify which salt you’re working with.

Safety and Handling

Zinc phosphate is generally low in acute toxicity, but it can cause eye and skin irritation. When handling the powder, wear gloves and safety goggles, and avoid inhaling dust. For solution preparation, follow your lab’s standard procedures and the safety data sheet (SDS). If you’re using it in a dental or industrial setting, follow the manufacturer’s instructions. This calculator is for educational and lab-planning purposes only, not for medical or clinical dosing.

Frequently Asked Questions

What is the molar mass of zinc phosphate in g/mol?

It is 386.11 g/mol for the anhydrous form. If you have the tetrahydrate (Zn3(PO4)2·4H2O), the molar mass is 458.17 g/mol.

How do I calculate the molar mass of Zn3(PO4)2?

Multiply the atomic mass of zinc (65.38) by 3, phosphorus (30.974) by 2, and oxygen (15.999) by 8, then add them: 196.14 + 61.948 + 127.992 = 386.08 g/mol (rounded to 386.11).

Is zinc phosphate soluble in water?

No, it is practically insoluble (Ksp ≈ 9.1 × 10-33). This is why it’s used as a precipitate in gravimetric analysis. If you need a soluble zinc phosphate solution, you’d have to use a different salt or a complexing agent.

What is the percent composition of zinc in zinc phosphate?

Zinc makes up about 50.8% of the mass: (3 × 65.38) / 386.11 × 100 = 50.8%. This is useful for converting between zinc mass and zinc phosphate mass.

Why does my textbook say 386.11 and my calculator says 386.08?

Different sources use slightly different atomic weights. The IUPAC standard gives 386.08, but many textbooks round atomic weights (e.g., Zn to 65.4) and get 386.11. Both are acceptable; use the value your instructor or method requires.

How do I prepare a 0.1 M solution of zinc phosphate?

Because zinc phosphate is insoluble, you cannot simply dissolve it in water. You would need to dissolve it in an acid (like dilute HCl) or use a soluble zinc salt and phosphate salt in a precipitation reaction. For a hypothetical solution, you’d weigh 0.1 × 386.11 = 38.611 g and dissolve to 1 L, but in practice this won’t work without a solvent that dissolves it.

Follow your lab method, the safety data sheet (SDS) and your supervisor when handling any chemical.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 386.11 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →