Molecules moving around each other is the process of diffusion — the net movement of particles from a region of higher concentration to a region of lower concentration, driven by their random thermal motion. This page explains what causes that motion, how diffusion works in gases, liquids, and solids, and how to calculate the rate at which it happens. You enter the diffusion coefficient, distance, and time, and the calculator returns the mean squared displacement or the time needed for molecules to travel a given distance.
Formula
The key equation for three-dimensional diffusion is the Einstein–Smoluchowski relation:
t = x² / (2D)
where:
- t = time (seconds)
- x = root-mean-square displacement (meters)
- D = diffusion coefficient (m²/s)
The factor 2 applies to one-dimensional diffusion; for two dimensions it is 4D, and for three dimensions it is 6D. This calculator uses the 2D form because it is the most common in lab contexts (e.g., molecules spreading on a surface or in a thin film).
Worked Example
Using the default values: D = 2.0 × 10⁻⁹ m²/s (a typical value for a small molecule like glucose in water at 25 °C) and x = 0.001 m (1 mm).
t = (0.001)² / (2 × 2.0 × 10⁻⁹) = 1.0 × 10⁻⁶ / (4.0 × 10⁻⁹) = 250 s
So a molecule diffuses 1 mm in about 250 seconds (4.2 minutes). The mean squared displacement is 2Dt = 2 × 2.0 × 10⁻⁹ × 250 = 1.0 × 10⁻⁶ m², which matches x².
Assumptions
- Diffusion is passive and driven only by thermal motion (no convection, no external forces).
- The medium is homogeneous and isotropic.
- The diffusion coefficient is constant over the time and distance considered.
- Molecules do not interact with each other (ideal dilute solution).
What Makes Molecules Move?
All atoms and molecules vibrate, rotate, and translate because they have thermal energy. At any temperature above absolute zero (−273.15 °C), particles possess kinetic energy proportional to temperature. In a gas, molecules fly freely; in a liquid, they slide past each other; in a solid, they vibrate around fixed positions. The random, jittery motion is called Brownian motion, named after botanist Robert Brown who observed pollen grains dancing in water in 1827. Albert Einstein explained in 1905 that this motion is caused by collisions with water molecules.
Because motion is random, molecules do not move in straight lines. They take a “random walk” — each step is in a random direction. Over time, the net displacement grows, but not linearly with time; it grows with the square root of time. That is why the formula uses x², not x.
Diffusion in Different States of Matter
The rate of diffusion depends strongly on the phase:
- Gases: Diffusion is fastest. Typical D values are 10⁻⁵ to 10⁻⁴ m²/s. For example, oxygen in air has D ≈ 1.8 × 10⁻⁵ m²/s at 25 °C.
- Liquids: Diffusion is much slower because molecules are packed closely. Typical D values are 10⁻⁹ to 10⁻¹⁰ m²/s. Glucose in water at 25 °C has D ≈ 6.7 × 10⁻¹⁰ m²/s.
- Solids: Diffusion is extremely slow. D values are often 10⁻¹⁴ m²/s or lower. For example, carbon in iron at room temperature diffuses at about 10⁻¹² m²/s, which is why case hardening requires high temperatures.
Temperature increases D because particles move faster. As a rule of thumb, D roughly doubles for every 10 °C rise in temperature for liquids, though this varies.
Why Does Diffusion Matter?
Diffusion is fundamental in biology, chemistry, and engineering:
- Oxygen and carbon dioxide exchange in the lungs and cells relies on diffusion across membranes.
- Nutrients reach cells in the body via diffusion when blood flow is low.
- In chemistry, mixing reactants relies on diffusion when stirring is absent.
- Semiconductor doping uses diffusion of impurities into silicon wafers.
- Food preservation and packaging rely on diffusion of gases through plastic films.
A practical consequence: diffusion is slow over macroscopic distances. A dye drop in a still glass of water takes hours to spread evenly. That is why we stir — stirring moves fluid, not just molecules.
How to Measure or Estimate the Diffusion Coefficient
The diffusion coefficient D is not something you can compute from a simple formula for every substance; it depends on the molecule size, solvent viscosity, and temperature. However, for spherical particles in a dilute liquid, the Stokes–Einstein equation gives a good estimate:
D = kBT / (6πηr)
where kB is Boltzmann’s constant (1.380649 × 10⁻²³ J/K), T is absolute temperature (K), η is solvent viscosity (Pa·s), and r is the particle radius (m). For water at 25 °C, η ≈ 8.9 × 10⁻⁴ Pa·s. For a small molecule like glucose (radius ~0.4 nm), this gives D ≈ 6.7 × 10⁻¹⁰ m²/s, matching experiments.
In practice, D is often measured experimentally using techniques like NMR, fluorescence recovery after photobleaching (FRAP), or diffusion cells. For this calculator, you must supply D — either from a table, a previous experiment, or the Stokes–Einstein estimate.
Common Mistakes and Misconceptions
- Confusing distance with displacement: The formula uses the straight-line displacement from start to end, not the total path length. A molecule may travel many meters in a zigzag but end up only a millimeter away.
- Using the wrong dimension factor: For 3D diffusion, use x² = 6Dt, not 2Dt. This calculator is for 2D; adjust if you are modeling a bulk solution.
- Forgetting temperature: D is temperature-dependent. A value measured at 20 °C is not valid at 37 °C.
- Assuming convection is absent: In real labs, even slight temperature differences cause convection currents that speed up mixing far beyond pure diffusion. The calculator only applies to quiescent conditions.
- Thinking diffusion is fast over long distances: Doubling the distance quadruples the time. That is why diffusion works well on the cellular scale (micrometers) but is useless for mixing a liter of solution.
Practical Example: How Long to Diffuse Across a Cell?
A typical cell is about 10 micrometers (1 × 10⁻⁵ m) in diameter. Using D = 1 × 10⁻⁹ m²/s (a typical protein in water), the time to diffuse across the cell is:
t = (1 × 10⁻⁵)² / (2 × 1 × 10⁻⁹) = 1 × 10⁻¹⁰ / 2 × 10⁻⁹ = 0.05 s
So a small protein can cross a cell in 50 milliseconds — fast enough for cellular processes. But for a 1 cm distance, the same molecule would take 5 × 10⁷ seconds (about 1.6 years) — clearly impractical. This is why organisms rely on blood flow and stirring for long-distance transport.
Frequently Asked Questions
What does “moving around each other” mean exactly?
It means molecules slide past one another, exchanging positions, due to their random thermal motion. In liquids, molecules are in constant contact but can rearrange; in gases, they fly freely and collide. This motion is what allows substances to mix without external stirring.
Why does diffusion happen faster in gases than liquids?
In gases, molecules are far apart and have long mean free paths — they travel long distances between collisions. In liquids, molecules are densely packed and constantly collide, so their net movement is slower. The diffusion coefficient in a gas is typically 10,000 times larger than in a liquid.
Does diffusion ever stop?
No. Even when concentrations are equal, molecules keep moving. The net flux becomes zero because equal numbers move in each direction, but individual molecules continue to move randomly. This is called dynamic equilibrium.
Can diffusion be accelerated?
Yes, by increasing temperature (which raises kinetic energy), by reducing the distance (thinner barriers), or by increasing the concentration gradient. Stirring or convection is not diffusion — it is bulk flow, which is much faster.
What is the difference between diffusion and osmosis?
Diffusion is the movement of any particles from high to low concentration. Osmosis is the specific movement of water molecules across a semipermeable membrane, driven by differences in solute concentration. Osmosis is a type of diffusion, but it involves a membrane and water only.
How do I know which D value to use?
Look up experimental values for your specific molecule and solvent at your temperature. If unavailable, estimate using the Stokes–Einstein equation, but remember that non-spherical molecules and interactions will cause deviations. When in doubt, use a range of D values to see how sensitive your result is.
Limits of the Formula
The Einstein relation assumes a homogeneous, isotropic medium and no external forces. It fails for very short times (before the random walk regime), for concentrated solutions where molecules interact, and for porous media where obstacles slow diffusion. It also does not account for chemical reactions that consume or produce the diffusing species. For those cases, more advanced models (e.g., Fick’s laws with reaction terms) are needed.
Always follow your lab method, the safety data sheet (SDS) and your supervisor when performing experiments.
Related
Formula used
in D | Diffusion coefficient | m²/s | 2.0e-9 | 0 in x | Distance traveled | m | 0.001 | 0 out t | Time to travel distance | s | x^2 / (2 * D) | 4 out msd | Mean squared displacement | m² | 2 * D * t | 8
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Within 10 Percent Calculator – How to Use It5.00 %
- W/W Percentage Calculator: Formula & Examples2.92 %
- Percent Equation: Formula & How to Use It
- Percent of a Number Calculator: Find It Instantly20.00 %
- UWW GPA Calculator: How to Compute Your GPA
- PPM to w/w Calculator: Convert Easily5.0000 %