molecalculator

Moles & Molar Mass

98% Sulfuric Acid Normality Calculator

Calculator No. 01-2486 · Updated · Formula and assumptions shown below

Normality 36.8 eq/L
Molarity
18.39 mol/L
= (Sulfuric acid purity ÷ 100) × Solution density × 1000 ÷ 98.079
Acid mass per liter
1,803.2 g/L
= (Sulfuric acid purity ÷ 100) × Solution density × 1000
Sulfuric acid purity
98 %
Set in the form below
You enter
Sulfuric acid purity (%), Solution density (g/mL)
You get
Normality (eq/L), Molarity (mol/L), Acid mass per liter (g/L)
Rounding
1 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator finds the normality of 98% sulfuric acid from its mass percentage and density, returning equivalents per liter (N). Enter the acid’s density in g/mL and its purity as a percent; the default values give about 36.7 N.

Formula

For sulfuric acid in a neutralization reaction, normality equals the number of acid equivalents per liter. Sulfuric acid (H2SO4) can donate two protons, so its acid equivalent factor is 2:

N = (purity / 100) × density × 1000 × 2 / 98.079

  • N is normality in equivalents per liter (eq/L), conventionally written N.
  • Purity is the mass percentage of H2SO4 in the supplied solution (% by mass).
  • Density is the solution density in grams per milliliter (g/mL), at the temperature applicable to the density value.
  • 1000 converts milliliters to liters (1 L = 1000 mL).
  • 2 is the acid equivalent factor for complete neutralization of both acidic protons.
  • 98.079 g/mol is the molar mass of H2SO4, calculated using standard atomic weights (2 × 1.008 + 32.06 + 4 × 15.999).

The calculator also reports molarity, the moles of H2SO4 per liter, and acid mass per liter. For this acid-base reaction, normality is twice molarity. The expression includes the required conversion from g/mL to g/L by multiplying by 1000.

Worked Example

Using the defaults—98% by mass and density 1.84 g/mL—the mass of pure sulfuric acid in one liter is:

0.98 × 1.84 g/mL × 1000 mL/L = 1803.2 g/L

Molarity is acid mass per liter divided by molar mass:

1803.2 g/L ÷ 98.079 g/mol = 18.386 mol/L (rounded)

For complete neutralization, each mole supplies two acid equivalents:

18.386 mol/L × 2 eq/mol = 36.77 eq/L

Rounded to the calculator’s one decimal place, the normality is 36.8 N. The calculator’s helper outputs are 18.39 mol/L and 1803.2 g/L. Small differences in the last displayed digit can arise from rounding intermediate values; the calculator evaluates the full expression before rounding.

Assumptions

  • The purity value is a mass fraction expressed as percent, not a volume percentage.
  • The supplied density applies to the acid solution and its relevant temperature. The default 1.84 g/mL is a conventional approximate value for concentrated 98% sulfuric acid near room temperature; check the reagent label or certificate for the actual value.
  • The result uses complete neutralization of both protons, giving an equivalent factor of 2. Normality is reaction-dependent; a different reaction endpoint can require a different factor.
  • The volume basis is one liter of final acid solution. Density converts that solution volume to mass.

Why 98% Acid Is About 36.8 N

The percentage alone cannot determine normality. A 98% solution means 98 g of sulfuric acid in every 100 g of solution—not 98 g in every 100 mL. To obtain a per-liter concentration, density is needed to convert the liter of solution into its mass.

At the default density, one liter weighs about 1840 g. At 98% by mass, that contains 1803.2 g of H2SO4. Dividing by the molar mass gives about 18.39 mol/L. Because sulfuric acid is diprotic, complete neutralization corresponds to about 36.77 equivalents per liter. This is why concentrated sulfuric acid has a normality much higher than 1 N.

Commercial specifications and density can vary with temperature, concentration, and product tolerances. Treat 36.8 N as an estimate when using the defaults, not a certified assay. For high-accuracy work, use the stated assay and density for the actual material and follow the applicable analytical method.

Normality, Molarity, and Reaction Endpoints

Molarity is a substance-based concentration: moles of solute per liter of solution. Normality counts reactive equivalents per liter, so it depends on the reaction being considered. For acid-base neutralization to a point where both sulfuric acid protons have reacted, the factor is 2 and N = 2M.

That relationship should not be treated as a universal property of every sulfuric acid reaction. In a reaction involving only one proton per molecule, the relevant equivalent factor may be 1; in oxidation-reduction chemistry, equivalents are defined by electron transfer and the factor depends on the balanced reaction. Always state the reaction basis when reporting normality. Molarity is often less ambiguous because it does not change with the chosen reaction.

Using and Checking the Result

Enter the purity and density from the reagent information, keeping the units exactly as shown. A purity of 98% is entered as 98, not 0.98. Density must be in g/mL; if a source gives g/L, convert it to g/mL by dividing by 1000 before entering it. The output is calculated for a liter of solution, not a liter of water or solvent.

  • Use normality when a specified reaction or titration method expresses concentration in equivalents per liter.
  • Use molarity when the method calls for moles per liter or when you need an unambiguous amount concentration independent of reaction endpoint.
  • Retain enough significant figures during calculations. Rounding an intermediate molarity too early can shift the final normality.
  • For a measured or standardized solution, use the experimentally determined concentration rather than relying solely on a nominal label value.

This calculator is a concentration calculation, not a mixing or dilution procedure. Concentrated sulfuric acid is highly corrosive and mixing it with water releases substantial heat. For any bench work, follow your lab method, the safety data sheet (SDS), and your supervisor; use appropriate training and protective controls. Do not infer a safe handling method from the arithmetic here.

Frequently Asked Questions

What is the normality of 98% sulfuric acid?
Using density 1.84 g/mL and complete neutralization of both protons, it is approximately 36.8 N. The precise value depends on the actual assay and density.

Is 98% sulfuric acid 18 N or 36 N?
Its molarity is about 18.4 mol/L. For complete acid-base neutralization, sulfuric acid provides two equivalents per mole, so its normality is about 36.8 N. The two numbers describe different concentration measures.

Why does density matter when calculating normality?
The 98% figure is mass by mass. Density tells you how many grams of the whole solution are present in one liter, which is necessary to calculate grams of acid per liter.

Does sulfuric acid always have twice the molarity as normality?
No. N = 2M applies when both acidic protons count in the reaction. Normality depends on the reaction and endpoint; molarity does not.

Can I use 98% purity without checking the density?
Only for a rough estimate with an assumed density. For a reliable result, use the density applicable to the solution and temperature, ideally from the reagent’s documentation.

Related

Formula used
in p | Sulfuric acid purity | % | 98 | 0 | 100
in d | Solution density | g/mL | 1.84 | 0.000001
out n | Normality | eq/L | (p / 100) * d * 1000 * 2 / 98.079 | 1
out m | Molarity | mol/L | (p / 100) * d * 1000 / 98.079 | 2
out w | Acid mass per liter | g/L | (p / 100) * d * 1000 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →