molecalculator

Moles & Molar Mass

PCB Calculator in EAGLE: Board Area and Dimensions

Calculator No. 01-3067 · Updated · Formula and assumptions shown below

Rectangular board area 80.00 cm^2
Rectangular board area
8,000 mm^2
= Board length × Board width
Board length
100 mm
Set in the form below
Board width
80 mm
Set in the form below
You enter
Board length (mm), Board width (mm)
You get
Rectangular board area (cm^2), Rectangular board area (mm^2)
Rounding
2 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

“PCB calculator EAGLE” usually means a way to calculate a printed circuit board’s dimensions or area while working in EAGLE, now part of Autodesk Fusion. This page calculator finds the rectangular board area from entered length and width; it does not calculate electrical properties or replace EAGLE’s board-layout and design-rule tools.

Formula

For a rectangular board, area equals length multiplied by width. Because the two inputs are in millimetres, the product is in square millimetres. To convert to square centimetres, divide by 100, since 1 cm = 10 mm and therefore 1 cm² = 100 mm².

  • l = board length in millimetres (mm).
  • w = board width in millimetres (mm).
  • a = rectangular board area in square centimetres (cm²): l × w ÷ 100.
  • amm = rectangular board area in square millimetres (mm²): l × w.

Worked Example

Using the calculator’s default dimensions, length is 100 mm and width is 80 mm.

Area in square millimetres = 100 mm × 80 mm = 8,000 mm².

Area in square centimetres = 8,000 mm² ÷ 100 = 80.00 cm².

The calculator’s headline result is therefore 80.00 cm². This is the area of the rectangle described by the two dimensions, not necessarily the area of copper, usable routing space, or the actual outline of an irregular board.

Assumptions

  • The board is treated as a rectangle with the entered length and width.
  • Both measurements use millimetres and describe the outer board dimensions.
  • The calculation does not account for cut-outs, rounded corners, notches, panel rails, or keep-out regions.

What EAGLE Does and What This Calculator Does

EAGLE is electronic design automation software used to create schematic diagrams and PCB layouts. A PCB layout describes component placement, copper traces, pads, board outlines, and other manufacturing details. The software’s editing and design-rule-checking features help users build and inspect that layout; this simple calculator supplies a geometric estimate from two dimensions.

The name can cause confusion because “PCB calculator” also refers to tools for trace width, impedance, voltage drop, or copper weight. Those calculations need different inputs and assumptions. Board area alone cannot tell you whether a trace can carry a particular current, whether a controlled-impedance line meets its target, or whether the layout satisfies electrical clearances.

In EAGLE, the board outline is generally represented by objects assigned to the designated board-outline layer. The precise workflow and interface can differ by software version. Measure the actual outer boundary in the layout rather than assuming the schematic or a component’s footprint defines the finished board size. If you are using a version integrated with a larger design environment, check its current documentation for the relevant measurement and export commands.

Using the Result for a Real Board Outline

For a rectangular outline, enter the maximum external length and width. If the outline is not rectangular, the calculator’s result is only the area of its bounding rectangle: the smallest rectangle that contains the shape. A board with a notch or curved edge will have less material area than that bounding rectangle. A CAD area measurement or geometry calculation based on the actual outline is needed for a closer estimate.

For instance, a 100 mm by 80 mm board has a bounding area of 80 cm². If a rectangular corner notch is 10 mm by 20 mm, its area is 200 mm², or 2 cm². Subtracting that cut-out gives 78 cm², provided there are no other excluded regions and the notch is entirely removed from the board. Rounded corners require the area of the removed corner segments rather than treating them as full rectangular cut-outs.

Area can help with early size comparisons and rough material estimates, but it is not enough to determine manufacturing cost. A fabricator may price boards by panel utilization, quantity, layer count, thickness, finish, minimum features, and other specifications. Obtain a quote using the actual manufacturing files and requirements when cost matters.

Common Measurement Problems

  • Mixing units: Enter both dimensions in millimetres. If a drawing gives centimetres, multiply each measurement by 10 before entering it; if it gives inches, multiply by 25.4 to convert to millimetres.
  • Using the wrong edges: Measure from the outside of the board outline, not between component centers or footprint boundaries.
  • Counting a cut-out as board: The basic formula includes the entire rectangle, including any holes or notches within it.
  • Confusing area and dimensions: A result of 80 cm² does not mean the board is 80 cm long. The length and width remain separate measurements.
  • Rounding too early: Keep the source dimensions at their useful precision, calculate first, then round the displayed area to a sensible number of decimal places.

Check that the outline is closed and that its objects use the intended layer before relying on a CAD-reported dimension or area. Small gaps, overlapping segments, and accidental geometry can lead to misleading measurements or manufacturing data. Design-rule checks address configured rules such as clearances and trace widths; they do not automatically prove that a board will work in every electrical or mechanical context.

Related PCB Calculations

If your question is about a trace rather than board size, identify the specific quantity first. Trace-width calculations commonly require current, copper thickness, allowable temperature rise, and a chosen standard or design method. Impedance estimates also depend on stack-up geometry and dielectric properties. These are separate engineering calculations, and a generic area calculator cannot produce dependable answers for them.

Similarly, a board’s surface area does not directly give its copper area. Copper may occupy only part of each layer, and the amount depends on pours, traces, planes, clearances, and cut-outs. For a reliable manufacturing estimate, use the board’s layer data and outline rather than multiplying the overall dimensions by the number of layers.

Frequently Asked Questions

Does EAGLE have a PCB area calculator?
EAGLE is primarily a schematic and PCB-layout application, not a general-purpose area calculator. You can inspect dimensions and layout geometry in the design environment, while this page provides a quick rectangular area calculation. Available commands vary by version.

How do I calculate PCB area from length and width?
Multiply length by width when both are in the same unit. For millimetres, divide the result in mm² by 100 to express it in cm². A 100 mm × 80 mm rectangle is 8,000 mm², or 80 cm².

Can I use this for a non-rectangular PCB?
Only as a bounding-rectangle estimate. For an accurate area, account for each cut-out and curved boundary or measure the closed board outline using suitable CAD geometry tools.

Is PCB area the same as copper area?
No. PCB area describes the board’s footprint; copper area is the portion covered by copper on one or more layers. A board may have substantial un-coppered regions, and each layer can have a different pattern.

Does the area tell me how much a PCB will cost?
No. Area is only one possible planning factor. Price also depends on order quantity, layer count, material and thickness, fabrication capabilities, finishing, panelization, and other specifications.

Related

Formula used
in l | Board length | mm | 100 | 0
in w | Board width | mm | 80 | 0
out a | Rectangular board area | cm^2 | l * w / 100 | 2
out amm | Rectangular board area | mm^2 | l * w | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →