molecalculator

Moles & Molar Mass

PCB Calculator Plus: What It Means and How to Calculate

Calculator No. 01-3080 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

“PCB calculator plus” is ambiguous: it may refer to a printed circuit board (PCB) calculator with an added feature, or to a calculator that includes “plus” in its name. There is no single standard tool identified by that phrase; this calculator estimates PCB copper trace width from current, copper thickness, temperature rise, and trace location, with the option to compare internal and external traces.

Formula

This page uses the IPC-2221 empirical trace-current relationship, a commonly cited first-pass estimate for copper conductors on a printed circuit board. In the equation, I = k × ΔT0.44 × A0.725, A is the trace cross-sectional area in square mils, and ΔT is the allowed temperature rise in degrees Celsius. The coefficient k is 0.048 for an external trace and 0.024 for an internal trace. Solving for width gives width = [I / (k × ΔT0.44)]1/0.725 / thickness.

  • I: current in amperes (A).
  • ΔT: temperature rise above ambient in degrees Celsius (°C), not the board’s absolute operating temperature.
  • A: copper cross-sectional area in square mils; 1 mil is 0.001 inch.
  • Thickness: copper thickness in ounces per square foot (oz/ft²), a conventional PCB copper-weight designation. The formula converts this using approximately 1.378 mil per ounce per square foot.
  • k: the empirical location coefficient, 0.048 external or 0.024 internal.

The calculator converts the resulting width from mils to millimetres using 25.4 mm per inch and 1,000 mils per inch, combined as 25.4 mm per 1,000 mils. The expression includes that conversion explicitly. “Plus” here means the page also lets you select trace location; it does not describe an official, universal PCB-calculator standard.

Worked Example

Using the defaults—1 A, 1 oz/ft² copper, 10 °C permitted rise, and an external trace—the coefficient is 0.048. First find the required cross-sectional area:

A = [1 / (0.048 × 100.44)]1/0.725 ≈ 21.13 square mils.

One ounce copper is approximately 1.378 mil thick, so the width is:

Width = 21.13 / 1.378 ≈ 15.33 mils.

Convert to millimetres: 15.33 × 25.4 / 1,000 ≈ 0.3894 mm, which rounds to 0.389 mm. This is a model estimate, not a guarantee that a real trace will stay below the chosen temperature rise.

What “PCB Calculator Plus” Can Refer To

PCB means printed circuit board, but calculators for board design cover several different tasks. A trace-width calculator estimates the minimum conductor width for a stated current and temperature rise. Other tools may estimate impedance, voltage drop, copper weight, board dimensions, or manufacturing cost. “Plus” is not a technical parameter or a recognized extra mode in the IPC-2221 equation; it may simply be wording used by a website, app, or search query.

That distinction matters. A tool that calculates trace width does not automatically calculate controlled impedance or voltage drop. Those questions require additional inputs and, in some cases, a different model. Check the calculator’s description and units before relying on a result. This page specifically calculates trace width from current, copper thickness, trace location, and permitted temperature rise.

How to Choose the Inputs

  • Current: enter the current that will flow through the trace under the design condition being assessed. For a changing load, determine whether you need to design for peak, continuous, or another defined current; the formula does not decide that for you.
  • Copper thickness: use the actual layer’s copper weight, not automatically the nominal outer-layer value. Finished copper thickness can differ from a bare-board starting value because of plating and fabrication details.
  • Temperature rise: choose a rise that is acceptable for the board and surrounding components. A smaller allowed rise produces a wider required trace.
  • Trace location: choose external for a trace exposed to the board’s outer surface and internal for a buried layer. The model uses different empirical coefficients because heat dissipation differs.

For example, changing the default location from external to internal increases the calculated width because the internal-trace coefficient is lower. The result should be rounded up to a practical width supported by the board layout and fabrication rules; rounding down can defeat the selected temperature-rise target.

Limits, Checks, and Common Mistakes

IPC-2221’s relationship is an empirical approximation, not a complete thermal simulation. Board thickness, nearby copper planes, airflow, trace length, enclosure, solder mask, via transitions, and neighboring heat sources can all affect temperature. The simplified equation does not model those details or account for every operating condition. Use it for initial sizing, then verify critical designs against applicable design requirements and suitable thermal analysis or testing.

  • Confusing temperature rise with operating temperature: a 10 °C rise means the conductor is estimated to be 10 °C above its local ambient, not that it operates at 10 °C.
  • Mixing copper units: the input is copper weight in oz/ft², not thickness in micrometres or millimetres. Convert correctly if your design data uses another unit.
  • Assuming a width is universally safe: the output is conditional on the selected inputs and model. It does not certify a board or replace a designer’s checks.
  • Ignoring voltage drop: a trace can meet a thermal estimate yet still have too much resistance or voltage drop for a circuit. Assess voltage drop separately where it matters.
  • Using too many displayed digits: the result’s three decimal places are useful for calculation, not a claim of manufacturing precision. Apply fabrication tolerances and round to a sensible design width.

For bench work or board validation, follow your lab method, the safety data sheet (SDS) and your supervisor. Electrical designs should also be reviewed for relevant current, temperature, insulation, and regulatory requirements.

Frequently Asked Questions

What does PCB calculator plus mean?
It is not a standard electronics term. It commonly describes a PCB calculator with extra options, or a search for a tool whose name includes “plus.” The exact meaning depends on the particular page or app.

How do I calculate PCB trace width?
Choose the trace current, copper thickness, permitted temperature rise, and whether the trace is internal or external. Apply an appropriate trace-current model, such as the IPC-2221 relationship used here, then verify the design’s thermal and electrical requirements.

Is this PCB trace-width result exact?
No. It is an estimate based on an empirical equation. Real board construction and cooling affect temperature, so important designs need additional engineering checks.

Should internal or external traces be wider?
For the same current, copper thickness, and allowed rise, this model generally gives a wider internal trace because its coefficient is lower. Actual board conditions can change how closely the estimate matches reality.

Does trace width determine impedance?
No. Trace width is one factor in impedance, but impedance also depends on the dielectric material, layer spacing, reference planes, copper geometry, and other stack-up details. Use a controlled-impedance calculation for that task.

Related

Formula used
in i | Current | A | 1 | 0
in d | Copper thickness | oz/ft² | 1 | 0.1
in t | Allowed temperature rise | °C | 10 | 0
sel p | Trace location | External=1, Internal=2
out w | PCB trace width | mm | (0.048 * (i / (t ^ 0.44)) ^ (1 / 0.725) / (d * 1.378)) * 25.4 * (p / 0.024) ^ (1 / 0.725) | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →