A PCB trace-width calculator estimates the minimum copper-track width needed to carry a specified current while keeping the temperature rise within a chosen limit. Enter current, copper thickness, allowable temperature rise, and whether the trace is on an outer or inner layer; the calculator returns an estimated width in millimeters and mils.
Formula
This calculator uses the IPC-2221 empirical trace-current relationship: I = k × ΔT0.44 × A0.725. Rearranging gives A = [I / (k × ΔT0.44)]1/0.725. In the formula, I is current in amperes, ΔT is the permitted temperature rise in °C, A is copper cross-sectional area in square mils, and k is 0.048 for an outer-layer trace or 0.024 for an inner-layer trace. The estimate of width is A divided by copper thickness in mils.
One ounce per square foot of copper corresponds to a nominal thickness of 1.37 mil, or about 0.0348 mm. The expression converts the calculated width from mils to millimeters using 0.0254 mm per mil. Copper weight is a nominal manufacturing specification; actual finished copper thickness can vary.
Worked Example
For the default values—1 A, a 10 °C allowable rise, 1 oz/ft² copper, and an outer-layer trace—the selected coefficient is k = 0.048. First calculate the required cross-sectional area:
A = [1 / (0.048 × 100.44)]1/0.725 ≈ 14.648 square mils.
Convert the nominal copper thickness: 1 oz/ft² × 1.37 mil per oz/ft² = 1.37 mil. Then divide area by thickness: 14.648 / 1.37 ≈ 10.692 mil. Convert to millimeters: 10.692 × 0.0254 ≈ 0.2716 mm. Rounded to two decimal places, the calculator’s headline result is 0.27 mm.
Assumptions
- The equation is the empirical IPC-2221 relationship, not a precise thermal simulation.
- Copper thickness uses the nominal conversion 1 oz/ft² = 1.37 mil.
- The entered current is treated as steady current; the formula does not model pulses, duty cycle, or transient heating.
- The result is a starting estimate and assumes no special thermal or manufacturing constraints.
How to Use the Result
Use the calculated value as an initial minimum width for a trace carrying the entered current under the selected temperature-rise assumption. A larger width usually reduces resistance and heating, and it may offer more margin for production variation. The calculator does not decide whether the trace fits the board or meets every electrical, thermal, or fabrication requirement.
The layer selection matters because an outer trace can shed heat to its surroundings more readily than a trace buried between board layers. The equation represents this difference through its k coefficient. For otherwise identical inputs, choosing an inner layer generally produces a wider estimate.
Temperature rise is the increase above the local board environment, not the absolute trace temperature. For example, a 10 °C rise in a 25 °C environment implies an estimated trace temperature near 35 °C under the assumed steady condition. If the board runs hotter, or nearby components add heat, the same rise may still lead to a higher absolute temperature.
Choosing Current, Copper, and Margin
Before relying on a calculator result, define the real design conditions. Consider these factors:
- Current profile: Use the continuous current for a steady load. Repetitive pulses and brief peaks need a thermal analysis that accounts for pulse duration and spacing.
- Temperature limit: Choose a rise compatible with the board material, nearby parts, and operating environment. A smaller permitted rise increases the calculated width.
- Finished copper: Check the fabricator’s stack-up and finished copper specification, rather than assuming nominal copper weight is exact.
- Available space: Wider traces need more routing area and can affect clearances, solder-mask openings, and connector geometry.
- Reliability margin: Consider using a width above the mathematical minimum where space allows, especially when current, ambient temperature, or copper thickness is uncertain.
For a supply or return path, calculate the relevant current in the trace segment itself. Current can divide among parallel branches, and a shared ground segment may carry the combined return currents of several loads. Do not assume every trace in a circuit carries only the current of one component.
Limits and Common Misconceptions
A trace-width calculator does not guarantee that a design is safe or compliant. The IPC-2221 equation is a broad empirical estimate, and real trace temperature depends on board construction, copper planes, airflow, enclosure, neighboring heat sources, and trace length. For high-current or safety-critical designs, use a more complete thermal method and review applicable design and manufacturing requirements.
A common misconception is that the result is a universal “ampacity” rating. It is not: the answer depends on the chosen temperature rise, copper thickness, layer position, and assumptions. Another frequent mistake is to confuse copper weight with thickness in ounces. The calculator interprets copper weight as oz/ft² and applies a nominal thickness conversion; it does not mean the trace is one ounce thick.
Also distinguish trace width from trace resistance. Width affects resistance, but length, copper resistivity, and temperature matter too. This calculator estimates width from current and a temperature-rise target; it does not calculate voltage drop or power loss. Those checks may require separate calculations, particularly for long traces or low-voltage power rails.
Frequently Asked Questions
How wide should a PCB trace be for 1 amp?
The answer depends on copper thickness, layer location, and allowable temperature rise. With the defaults here—1 oz/ft² copper, outer layer, and a 10 °C rise—the estimate is 0.27 mm. Treat it as a starting point, not a universal rule.
Does an inner-layer trace need to be wider?
Usually, under this equation’s assumptions. The calculator uses a lower heat-dissipation coefficient for an inner layer, so it estimates a larger width for the same current, copper, and temperature rise.
What does temperature rise mean for a PCB trace?
It is the estimated increase in trace temperature above the surrounding reference environment while carrying current. It is not the trace’s absolute temperature and does not account for every heat source on a board.
Is IPC-2221 trace width exact?
No. It is an empirical estimate, not a substitute for measuring or simulating the thermal behavior of a specific board. Layout, stack-up, airflow, and nearby heating can change the result.
Does this calculator check voltage drop?
No. It estimates width from current and temperature rise. Voltage drop and resistive loss also depend on trace length and copper resistance, so evaluate those separately when they matter.
Practical Design Check
After selecting a width, verify the design in the context of the complete PCB: check current paths, layer stack-up, clearances, connectors, and fabrication limits. Confirm that the finished copper and operating environment match the inputs. For bench work or prototype testing, follow your lab method, the safety data sheet (SDS), and your supervisor.
Related
Formula used
in i | Trace current | A | 1 | 0 in dt | Allowable temperature rise | °C | 10 | 0 in t | Copper thickness | oz/ft² | 1 | 0 sel layer | Trace layer | Outer=1, Inner=2 out w | Estimated trace width | mm | (pow((i / (0.048 * pow(dt,0.44))), (1 / 0.725)) / (0.024 * pow(t,0.725))) / (layer == 1) | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp