molecalculator

Moles & Molar Mass

Percentage by Volume Formula: Definition & Examples

Calculator No. 01-9133 · Updated · Formula and assumptions shown below

Percentage by volume 40.00 % v/v
Ratio (solute:solution)
0.4000
= Volume of solute ÷ Total volume of solution
Volume of solute
40 mL
Set in the form below
Total volume of solution
100 mL
Set in the form below
You enter
Volume of solute (mL), Total volume of solution (mL)
You get
Percentage by volume (% v/v), Ratio (solute:solution)
Rounding
2 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Percentage by volume (v/v%) is a unit of concentration that expresses the volume of a solute divided by the total volume of the solution, multiplied by 100. To calculate it, you enter the volume of solute and the final total volume of the solution, and the calculator returns the v/v% concentration. This formula is standard for liquid-in-liquid mixtures such as alcohol solutions, vinegar, and many industrial reagents.

Formula

The percentage by volume formula is written as:

% v/v = (Volume of solute ÷ Total volume of solution) × 100

Where:

  • Volume of solute – the volume of the substance being dissolved, in millilitres (mL) or any consistent volume unit.
  • Total volume of solution – the final volume after mixing, in the same unit as the solute volume.
  • % v/v – the concentration expressed as a percentage by volume.

Both volumes must use the same unit (mL, L, cm³). The result is dimensionless, but it is conventionally written with “% v/v” or “% (v/v)” to distinguish it from mass-based percentages.

Worked Example

Using the calculator defaults: 40 mL of ethanol is mixed with enough water to make a total solution volume of 100 mL.

  1. Identify the solute volume: 40 mL
  2. Identify the total solution volume: 100 mL
  3. Divide: 40 ÷ 100 = 0.4
  4. Multiply by 100: 0.4 × 100 = 40% v/v

The result is 40% v/v. This means 40 mL of pure ethanol is present in every 100 mL of the final solution.

Assumptions

  • Volumes are additive – this is an approximation; real mixing can cause slight volume contraction or expansion (e.g., ethanol and water).
  • The solute is a liquid at the given temperature.
  • Temperature is constant – volumes change with temperature, so % v/v is temperature-dependent.
  • The total volume is measured after mixing, not the sum of individual volumes before mixing.

When to Use Percentage by Volume

Use % v/v when both the solute and the solvent are liquids. Common applications include:

  • Alcoholic beverages – “40% ABV” (alcohol by volume) is a percentage by volume.
  • Laboratory reagents – many acids and bases are sold as v/v% solutions (e.g., 10% HCl).
  • Household products – vinegar is typically 5% acetic acid by volume.
  • Cleaning and disinfecting solutions – diluting concentrates to a working concentration.

If the solute is a solid (e.g., salt in water), use percentage by mass (w/w%) or mass/volume percent (w/v%) instead.

How to Read the Result

The result tells you how many parts of solute are present per 100 parts of solution by volume. For example, a 5% v/v solution contains 5 mL of solute in every 100 mL of solution. This is not the same as 5 mL of solute plus 95 mL of solvent – the total must equal 100 mL. To prepare a 5% v/v solution, you would measure 5 mL of solute and add solvent until the total volume reaches 100 mL.

Common Mistakes and Misconceptions

  • Using solvent volume instead of solution volume – the denominator is the final total volume, not the volume of solvent added. Adding 40 mL solute to 60 mL solvent gives a total of 100 mL, but adding 40 mL solute to 100 mL solvent gives a total of 140 mL – the % v/v is different.
  • Ignoring volume contraction – when mixing ethanol and water, the final volume is less than the sum of the individual volumes. Always measure the final volume after mixing.
  • Mixing units – if solute is in mL and total is in L, convert first (1 L = 1000 mL).
  • Confusing % v/v with % w/v – a 10% w/v solution has 10 grams of solute per 100 mL, not 10 mL.

Limitations of the Formula

Percentage by volume is simple but has limits. It is not suitable for solids or gases dissolved in liquids. It also assumes volumes are additive, which is not true for many mixtures – ethanol and water, for example, show a volume decrease of about 4% when mixed. For precise work, use molarity or molality instead. % v/v also changes with temperature because liquids expand, so always note the temperature when reporting a value.

Frequently Asked Questions

How do I calculate % v/v from volumes?

Divide the volume of solute by the total volume of solution, then multiply by 100. For example, 25 mL of solute in a 200 mL solution is (25/200) × 100 = 12.5% v/v.

Is % v/v the same as ABV?

Yes, for alcoholic drinks, “alcohol by volume” (ABV) is a percentage by volume. A bottle labelled 12% ABV contains 12 mL of ethanol per 100 mL of the drink.

What is the difference between % v/v and % w/v?

% v/v uses volume of solute per volume of solution, while % w/v uses mass of solute (in grams) per volume of solution (in mL). A 10% w/v solution has 10 g of solute per 100 mL, not 10 mL.

Can I use % v/v for solid solutes?

No, % v/v is only for liquid solutes. For solids, use % w/w (mass of solute per mass of solution) or % w/v (mass per volume).

Why does the final volume differ from the sum of solute and solvent?

Because molecules pack differently when mixed. Ethanol and water, for instance, form hydrogen bonds that pull molecules closer, reducing total volume. Always prepare solutions by adding solvent to a volumetric flask up to the mark, not by adding pre-measured volumes.

How do I prepare a 70% v/v solution from a concentrated stock?

Use the dilution formula C1V1 = C2V2. For 100 mL of 70% from a 100% stock, V1 = (70 × 100) / 100 = 70 mL of stock, then add water to a final volume of 100 mL. Always add solvent to the mark, not the other way around, and follow your lab’s safety data sheet for handling the stock solution.

Follow your lab method, the safety data sheet (SDS), and your supervisor when preparing any solution.

Related

Formula used
in vs | Volume of solute | mL | 40 | 0
in vt | Total volume of solution | mL | 100 | 0.000001
out p | Percentage by volume | % v/v | vs / vt * 100 | 2
out r | Ratio (solute:solution) | - | vs / vt | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →