molecalculator

Moles & Molar Mass

pH and pOH Calculations: Formulas and Examples

Calculator No. 01-2494 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator works out pH and pOH from the hydrogen-ion or hydroxide-ion concentration, or converts between pH and pOH at 25 °C. Enter one concentration in mol/L or one pH/pOH value; the results include the paired scale and, where applicable, the corresponding ion concentration.

Formula

The basic definitions are pH = −log10([H+]/(1 mol/L)) and pOH = −log10([OH−]/(1 mol/L)). In these formulas, [H+] is hydrogen-ion concentration in mol/L and [OH−] is hydroxide-ion concentration in mol/L. Dividing by 1 mol/L makes the logarithm’s argument dimensionless. The calculator’s concentration inputs are entered as numerical values in mol/L, so its expressions are −log10(h) and −log10(oh).

For water at 25 °C, pH + pOH = pKw ≈ 14.00. The final calculator output adds the supplied pH and pOH values to show the sum; it does not infer missing values from the other input fields. To convert a known pH to pOH at 25 °C, use pOH = 14.00 − pH. To convert pOH to pH, use pH = 14.00 − pOH. The value 14.00 is a conventional approximation for water’s ion-product constant at 25 °C, not a universal constant at every temperature.

Worked Example

Using the default values, [H+] = 0.001 mol/L and [OH−] = 0.00001 mol/L. The pH from the hydrogen-ion concentration is:

pH = −log10(0.001) = 3.000.

The pOH from the hydroxide-ion concentration is:

pOH = −log10(0.00001) = 5.000.

The separate default pH and pOH entries are 3 and 5, so their displayed sum is pH + pOH = 3 + 5 = 8.000. This is not 14 because the calculator deliberately reports the sum of the two values entered; they are independent inputs, not a matched water-equilibrium pair. For the pH 3.000 calculated above, a matched pOH at 25 °C would instead be 14.00 − 3.000 = 11.00.

Assumptions

  • The conversion pH + pOH = 14.00 applies approximately to dilute aqueous solutions at 25 °C.
  • The concentration formulas use the entered molar concentrations directly. For precise thermodynamic pH, hydrogen-ion activity—not concentration alone—is the relevant quantity.
  • The pH meter reading is the real check: temperature and ionic strength shift pH, so calculations and measurements can differ.
  • This is study and lab-planning arithmetic. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

How pH and pOH Work

pH and pOH are logarithmic ways to express how acidic or basic an aqueous solution is. A one-unit change corresponds to a tenfold change in the relevant ion measure. For example, a solution at pH 4 has ten times the hydrogen-ion activity of one at pH 5 under comparable conditions. The logarithmic scale is useful because ion concentrations can span many orders of magnitude.

In introductory calculations, concentrations stand in for activities: pH ≈ −log10[H+]. In more exact chemistry, pH is defined using hydrogen-ion activity, which accounts for interactions among ions in solution. Those interactions become more important as ionic strength rises, so a concentration-based result can be an approximation rather than a precise measured pH.

Water establishes an equilibrium between hydrogen and hydroxide ions. Its ion product is Kw = a(H+)a(OH−), where a denotes activity. Taking negative base-10 logarithms gives pH + pOH = pKw. At 25 °C, pKw is approximately 14.00. At other temperatures, pKw changes; neutral water still has equal hydrogen and hydroxide activities, but its pH need not be 7.00.

Using the Calculator and Choosing an Input

The block evaluates the concentration-based pH and pOH formulas for the two concentration fields, and displays the sum of the separate pH and pOH entries. To perform a conversion, use the relevant field and ignore outputs that do not match the question you are solving:

  • To calculate pH from hydrogen-ion concentration, enter [H+] in mol/L and read “pH from [H+].”
  • To calculate pOH from hydroxide-ion concentration, enter [OH−] in mol/L and read “pOH from [OH−].”
  • To convert a known pH to pOH, use pOH = 14.00 − pH at 25 °C. To convert a known pOH to pH, use pH = 14.00 − pOH.

The calculator’s input fields allow nonnegative concentrations and any signed pH or pOH value. Realistic aqueous solutions have limits set by the substance, solvent, temperature and measurement method; the fields are not a claim that every entered value can be produced or accurately measured. A zero concentration cannot be inserted into a logarithm, because log10(0) is undefined. The calculator rejects zero for both concentration inputs.

Common Mistakes and Limitations

  • Mixing concentration units: The concentration inputs require mol/L. Convert mmol/L to mol/L by dividing by 1000 before entering it; for example, 2 mmol/L = 0.002 mol/L.
  • Reversing the sign: pH = −log10[H+], not log10[H+]. A concentration of 0.001 mol/L gives pH 3, not −3.
  • Assuming pH + pOH is always 14: This is approximately true at 25 °C in water. Use the appropriate pKw for other temperatures and conditions.
  • Treating pH as a direct concentration: A pH value is logarithmic. At pH 3, the idealized concentration is [H+] = 10−3 mol/L, not 3 mol/L.
  • Overinterpreting digits: A calculator may show several decimals, but input uncertainty, activity effects, temperature, calibration and sample handling can make those digits unjustified. Round according to the quality of the data.

These equations do not calculate the pH of a buffer from its ingredients, predict the result of mixing solutions, or account for weak-acid and weak-base equilibria. Those problems require additional information such as equilibrium constants, analytical concentrations, volume changes and sometimes activity corrections. A measured meter reading is the practical check, especially when accuracy matters.

Frequently Asked Questions

How do you calculate pH from hydrogen-ion concentration?
Use pH = −log10([H+]/(1 mol/L)). For a concentration entered numerically in mol/L, pH = −log10([H+]). Thus, 0.001 mol/L gives pH 3.000.

How do you calculate pOH from pH?
At 25 °C in water, use pOH ≈ 14.00 − pH. For example, pH 9.00 corresponds to pOH about 5.00. At another temperature, use that temperature’s pKw instead of 14.00.

How do you convert pOH to hydroxide concentration?
Rearrange the definition: [OH−] = 10−pOH mol/L. A pOH of 5.00 corresponds to 1.0 × 10−5 mol/L in the concentration-based approximation.

Is neutral pH always 7?
No. Neutrality means equal hydrogen and hydroxide activities. At 25 °C this corresponds approximately to pH 7.00, but the neutral pH changes with temperature because water’s ion-product constant changes.

Why can a measured pH differ from a calculated pH?
The calculation may use concentration rather than activity, or omit temperature, ionic-strength, equilibrium and measurement effects. Calibration, electrode condition and sample handling can also affect a reading. Check the meter reading and the assumptions behind the calculation.

Related

Formula used
in h | Hydrogen-ion concentration [H+] | mol/L | 0.001 | 0
in oh | Hydroxide-ion concentration [OH−] | mol/L | 0.00001 | 0
in ph | pH | - | 3 | -
in poh | pOH | - | 5 | -
out phh | pH from [H+] | - | -log10(h) | 3
out pohh | pOH from [OH−] | - | -log10(oh) | 3
out sum | pH + pOH at 25 °C | - | ph + poh | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →