molecalculator

Moles & Molar Mass

pH and pOH Formula: Calculate Acidity and Basicity

Calculator No. 01-2496 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The pH formula is pH = −log₁₀[H⁺], and the pOH formula is pOH = −log₁₀[OH⁻], where the bracketed values are molar concentrations in mol/L. This calculator converts either hydrogen-ion or hydroxide-ion concentration into pH and pOH, using the 25 °C relationship pH + pOH = 14.00.

Formula

The defining concentration formulas are:

  • pH = −log₁₀[H⁺], where [H⁺] is the molar concentration of hydrogen ions, in mol/L.
  • pOH = −log₁₀[OH⁻], where [OH⁻] is the molar concentration of hydroxide ions, in mol/L.
  • pH + pOH = pKw, where pKw = −log₁₀Kw and Kw is water’s ion-product constant.

At 25 °C, Kw is approximately 1.0 × 10−14, so pKw is approximately 14.00. Consequently, pOH = 14.00 − pH and pH = 14.00 − pOH at that temperature. The calculator’s first two results are calculated directly from the two input concentrations; its final result adds them so you can check whether they sum to 14.00.

The minus sign is important: a concentration of 1 × 10−4 mol/L gives a pH or pOH of 4, not −4. A logarithm is defined only for a positive value, so both concentration inputs must be greater than zero. The calculator does not accept zero because its logarithm would be undefined.

Worked Example

Using the calculator’s default values, [H⁺] = 0.0001 mol/L and [OH⁻] = 0.0001 mol/L:

  1. pH = −log₁₀(0.0001) = −log₁₀(1 × 10−4) = 4.00.
  2. pOH = −log₁₀(0.0001) = −log₁₀(1 × 10−4) = 4.00.
  3. pH + pOH = 4.00 + 4.00 = 8.00.

This pair of equal concentrations does not represent water at 25 °C in equilibrium: their product is 1 × 10−8, rather than water’s approximate Kw of 1 × 10−14. The example demonstrates the two logarithm calculations, while the sum output makes the mismatch with the 25 °C relationship visible. For a mutually consistent neutral-water example at 25 °C, each concentration is approximately 1 × 10−7 mol/L, yielding pH 7.00 and pOH 7.00.

Assumptions

  • The pH + pOH = 14.00 relationship assumes approximately 25 °C and uses Kw ≈ 1.0 × 10−14.
  • Concentrations are entered in mol/L, and the formulas use concentration as a practical approximation to ion activity.
  • The inputs are positive values for the hydrogen-ion and hydroxide-ion concentrations of the same solution if you want to check their sum.

What pH and pOH Mean

pH and pOH are logarithmic measures of acidity and basicity. A lower pH generally indicates greater hydrogen-ion activity, while a lower pOH generally indicates greater hydroxide-ion activity. In ordinary aqueous solutions near 25 °C, pH below 7 is described as acidic, pH 7 as neutral, and pH above 7 as basic. These labels depend on temperature: neutral means the hydrogen- and hydroxide-ion activities are equal, not that pH must always equal 7.

Because the scale is logarithmic, a one-unit change corresponds to a tenfold change in the relevant ion concentration when comparing idealized solutions. For example, [H⁺] = 1 × 10−3 mol/L gives pH 3, while [H⁺] = 1 × 10−4 mol/L gives pH 4. The latter has one-tenth the hydrogen-ion concentration. A two-unit difference corresponds to a hundredfold concentration difference.

The bracket notation [H⁺] means concentration, not the total number of hydrogen ions. In water, free protons do not exist as isolated particles; they are associated with water molecules and are commonly represented in introductory formulas as H⁺. That shorthand is convenient for calculations and does not imply that a bare proton is floating independently in solution.

How to Use the Calculator

Enter the hydrogen-ion and hydroxide-ion concentrations in mol/L. The calculator reports pH, pOH, and their sum. Use concentrations expressed in scientific notation when values are small: for example, 0.000001 mol/L is 1 × 10−6 mol/L and gives a pH of 6. If you know only one ion concentration, the other input is still required by this calculator; do not enter a guessed value as though it were measured.

For a solution known to be in equilibrium at about 25 °C, you can calculate the missing value using Kw:

  • [OH⁻] = Kw / [H⁺]
  • [H⁺] = Kw / [OH⁻]

Here, use Kw ≈ 1.0 × 10−14 at 25 °C. Alternatively, if you already know pH, calculate pOH as 14.00 − pH and then [OH⁻] = 10−pOH mol/L. These relationships are useful checks, but the input concentrations must refer to the same conditions and solution.

Concentration, Activity, and Temperature

The introductory formulas use concentration, but the thermodynamic definition of pH is based on hydrogen-ion activity. Activity accounts for interactions among ions and is often represented as an effective concentration. In dilute solutions, concentration can be a reasonable approximation; in more concentrated or strongly ionic solutions, the difference may matter. Therefore, a concentration-derived pH is an estimate when non-ideal effects are significant.

Water’s ion-product constant changes with temperature. The familiar pH + pOH = 14.00 result is an approximation for 25 °C, not a universal identity. At another temperature, use the applicable pKw: pH + pOH = pKw. Neutral water still has equal hydrogen- and hydroxide-ion activities, but its neutral pH can differ from 7 when the temperature changes.

Measured pH can also be affected by ionic strength, calibration, temperature, and the condition of the measurement system. The meter reading is the real check; temperature and ionic strength shift pH. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Common Errors and Limits

  • Using the wrong concentration units: enter mol/L, not mmol/L or mol/mL. Convert millimolar to molar by dividing by 1000; for instance, 2 mmol/L = 0.002 mol/L.
  • Dropping the negative sign: pH and pOH are the negative base-10 logarithms, not the logarithms themselves.
  • Assuming the sum is always 14: 14.00 applies approximately at 25 °C. The appropriate sum is pKw at other temperatures.
  • Confusing concentration with amount: moles alone do not determine pH; volume and chemical equilibrium may also be needed to find ion concentration.
  • Over-interpreting decimal places: a result displayed to two decimals does not guarantee that the input or model is accurate to two decimals. Precision depends on measurements and assumptions.

These formulas convert known ion concentrations to logarithmic values; they do not predict the pH of every acid or base from its name or starting amount. Weak acids and bases only partially ionize, and buffers resist changes in pH. Calculating those systems may require equilibrium constants, concentrations, and a suitable model. In real work, compare a calculation with a properly calibrated measurement when the value matters.

Frequently Asked Questions

What is the formula for pH?
pH = −log₁₀[H⁺], with [H⁺] expressed in mol/L in the concentration form used here.

What is the formula for pOH?
pOH = −log₁₀[OH⁻], with [OH⁻] in mol/L.

How are pH and pOH related?
They satisfy pH + pOH = pKw. At approximately 25 °C, pKw is about 14.00, so pH + pOH ≈ 14.00.

How do I find pH from pOH?
At 25 °C, subtract pOH from 14.00: pH ≈ 14.00 − pOH. At other temperatures, use pKw for that temperature instead of 14.00.

Can pH be negative or greater than 14?
Yes. The scale is not fundamentally limited to 0–14; sufficiently concentrated solutions can have values outside that range. In such cases, activity effects make simple concentration-based estimates less reliable.

Does pH 7 always mean neutral?
No. Neutrality means equal hydrogen- and hydroxide-ion activities. Neutral pH is approximately 7 at 25 °C, but changes with temperature.

Related

Formula used
in h | Hydrogen-ion concentration [H+] | mol/L | 0.0001 | 0
in oh | Hydroxide-ion concentration [OH-] | mol/L | 0.0001 | 0
out ph | pH | - | -log10(h) | 2
out poh | pOH | - | -log10(oh) | 2
out sum | pH + pOH | - | ph + poh | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →