molecalculator

Moles & Molar Mass

Pressure at Depth Calculation Formula

Calculator No. 01-11942 · Updated · Formula and assumptions shown below

Absolute pressure 201,843.2 Pa
Pressure in bar
2.018 bar
= Absolute pressure ÷ 100000
Pressure in atmospheres
1.992 atm
= Absolute pressure ÷ 101325
Depth (h)
10 m
Set in the form below
You enter
Depth (h) (m), Fluid density (ρ) (kg/m³), Surface pressure (P₀) (Pa)
You get
Absolute pressure (Pa), Pressure in bar (bar), Pressure in atmospheres (atm)
Rounding
1 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The pressure at depth in a fluid is calculated with the hydrostatic pressure formula P = P₀ + ρgh, where P₀ is the pressure at the surface, ρ is the fluid density, g is gravitational acceleration, and h is the depth. Enter the surface pressure, fluid density, and depth to get the absolute pressure in pascals, bars, or atmospheres.

Formula

The hydrostatic pressure equation is:

P = P₀ + ρgh

  • P – absolute pressure at depth (pascals, Pa)
  • P₀ – pressure at the surface (Pa); for water open to the atmosphere, this is 101,325 Pa (1 atm)
  • ρ – fluid density (kg/m³); freshwater ≈ 1000 kg/m³, seawater ≈ 1025 kg/m³
  • g – gravitational acceleration (9.80665 m/s², standard value)
  • h – depth below the surface (meters)

The term ρgh is the gauge pressure – the pressure added by the fluid column above the point. Adding P₀ converts gauge pressure to absolute pressure, which is what a sensor or your ears actually feel.

Worked Example

Using the default values from the calculator: depth = 10 m, fluid density = 1025 kg/m³ (seawater), surface pressure = 101,325 Pa.

  1. Calculate the gauge pressure: ρgh = 1025 × 9.80665 × 10 = 100,518.1625 Pa
  2. Add surface pressure: P = 101,325 + 100,518.1625 = 201,843.1625 Pa
  3. Convert to bar: 201,843.1625 / 100,000 = 2.018 bar
  4. Convert to atmospheres: 201,843.1625 / 101,325 = 1.992 atm

The calculator rounds the absolute pressure to 201843.2 Pa (one decimal), which matches the step-by-step result. At 10 m in seawater, the pressure is roughly twice the surface pressure.

Assumptions

  • The fluid is incompressible (density constant with depth) – valid for water in most diving and engineering contexts.
  • Gravity is constant at 9.80665 m/s² – a standard value; local gravity varies slightly with latitude and altitude.
  • The surface pressure P₀ is uniform and known – for open water, it is atmospheric pressure.
  • No temperature or salinity gradients that affect density – in the ocean, density changes slightly with depth, but the error is small for moderate depths.

When to Use This Formula

This formula applies to any fluid at rest – water in a tank, a swimming pool, the ocean, or even a column of mercury in a barometer. It is used in:

  • Scuba diving and freediving – to plan decompression and understand pressure effects on the body
  • Submarine and underwater vehicle design – hull strength calculations
  • Civil engineering – dam walls, lock gates, and water towers
  • Fluid mechanics – pressure at the bottom of a container
  • Oceanography – estimating pressure at depth for instruments

Remember that the formula gives pressure at a single depth. If the fluid is moving (e.g., a pipe or river), the dynamic pressure from Bernoulli’s equation must also be considered.

Common Mistakes and Misconceptions

  • Forgetting to add surface pressure – The formula P = ρgh alone gives gauge pressure. Absolute pressure = gauge + atmospheric. A tire gauge reads gauge pressure; a depth sensor reads absolute.
  • Using the wrong density – Freshwater is about 1000 kg/m³, seawater about 1025 kg/m³. Using freshwater for seawater underestimates pressure by about 2.5%.
  • Mixing units – If depth is in feet and density in kg/m³, you must convert feet to meters (1 ft = 0.3048 m). The calculator expects SI units.
  • Assuming pressure increases linearly with depth in gases – For air, density changes with pressure, so the simple formula fails. For water, density is nearly constant, so it works.
  • Confusing gauge and absolute pressure – A depth of 10 m in freshwater gives a gauge pressure of 98,066.5 Pa, but the absolute pressure is 199,391.5 Pa. Always state which one you mean.

Real-World Examples

  • Diving at 30 m in seawater: P = 101,325 + (1025 × 9.80665 × 30) = 101,325 + 301,554.5 = 402,879.5 Pa ≈ 4.0 atm. Divers experience 4 times the surface pressure.
  • Bottom of a 50 m freshwater lake: P = 101,325 + (1000 × 9.80665 × 50) = 101,325 + 490,332.5 = 591,657.5 Pa ≈ 5.84 atm.
  • Deep ocean trench (10,000 m): P ≈ 101,325 + (1025 × 9.80665 × 10,000) = 101,325 + 100,518,162.5 = 100,619,487.5 Pa ≈ 1000 atm. This is why only specially designed submersibles can reach such depths.

Safety and Limitations

When diving, never rely on a calculator to plan decompression stops – use certified dive tables and a dive computer. The hydrostatic formula gives static pressure; it does not account for pressure changes during ascent or descent, which can cause barotrauma or decompression sickness. Always follow your dive training and safety guidelines.

The formula assumes a homogeneous fluid. In the ocean, temperature and salinity gradients cause density to vary, but for depths up to a few hundred meters, the error is typically less than 1%. For extreme depths (over 1000 m), compressibility of water becomes noticeable – the density increases by about 0.5% per 1000 m, so the simple formula underestimates pressure slightly.

Frequently Asked Questions

What is the pressure at 10 meters of water?

At 10 meters of freshwater (density 1000 kg/m³), gauge pressure is 98,066.5 Pa (0.968 atm). Absolute pressure is 199,391.5 Pa (1.968 atm). In seawater (density 1025 kg/m³), absolute pressure is about 201,843 Pa (1.992 atm).

Does pressure double every 10 meters?

No, pressure increases linearly with depth, not exponentially. Every 10 meters of water adds about 1 atmosphere of pressure. So at 10 m absolute pressure is about 2 atm, at 20 m about 3 atm, at 30 m about 4 atm – each 10 m adds roughly 1 atm.

What is the difference between gauge pressure and absolute pressure?

Gauge pressure is the pressure above atmospheric pressure – it is what a pressure gauge reads. Absolute pressure is gauge pressure plus atmospheric pressure. For example, at 10 m depth in freshwater, gauge pressure is 98,066.5 Pa, absolute pressure is 199,391.5 Pa.

Does the formula work for air or other gases?

For gases, density changes with pressure, so the simple formula is only accurate for very small heights (a few meters). For accurate gas pressure at altitude, you need the barometric formula, which accounts for density variation.

Why does water pressure not depend on the width of the container?

Hydrostatic pressure depends only on depth and fluid density, not on the container’s shape or volume. A narrow tube and a wide lake have the same pressure at the same depth because pressure is caused by the weight of the fluid column directly above the point.

How do I convert pressure to psi or bar?

1 bar = 100,000 Pa; 1 atm = 101,325 Pa; 1 psi = 6,894.76 Pa. To convert from pascals to psi, divide by 6894.76. The calculator provides bar and atm outputs, but you can easily convert to psi by multiplying the Pa result by 0.000145038.

Related

Formula used
in m | Depth (h) | m | 10 | 0
in rho | Fluid density (ρ) | kg/m³ | 1025 | 0
in p0 | Surface pressure (P₀) | Pa | 101325 | 0
out p | Absolute pressure | Pa | p0 + rho * 9.80665 * m | 1
out pbar | Pressure in bar | bar | p / 100000 | 3
out patm | Pressure in atmospheres | atm | p / 101325 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →