molecalculator

Moles & Molar Mass

Pressure Density Depth Formula for Fluids

Calculator No. 01-2087 · Updated · Formula and assumptions shown below

Pressure increase 98,066 Pa
Pressure increase
98.067 kPa
= Pressure increase ÷ 1000
Fluid density
1000 kg/m^3
Set in the form below
Depth below surface
10 m
Set in the form below
You enter
Fluid density (kg/m^3), Depth below surface (m), Gravitational acceleration (m/s^2)
You get
Pressure increase (Pa), Pressure increase (kPa)
Rounding
0 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The pressure–density–depth formula is ΔP = ρgh: pressure increase equals fluid density multiplied by gravitational acceleration and depth. Enter density in kg/m³, depth in metres, and gravity in m/s² to calculate the pressure increase in pascals; the result is gauge pressure relative to the fluid’s surface.

Formula

The hydrostatic pressure formula is ΔP = ρgh. Here, ΔP is the pressure increase from the fluid surface to the point of interest, measured in pascals (Pa); ρ (rho) is fluid density in kilograms per cubic metre (kg/m³); g is gravitational acceleration in metres per second squared (m/s²); and h is vertical depth below the surface in metres (m). The calculator also reports that pressure increase in kilopascals, using 1 kPa = 1,000 Pa.

At Earth’s surface, standard gravitational acceleration is 9.80665 m/s². The calculator treats density as constant and assumes the fluid is at rest. Because the formula gives a pressure difference, it does not include the pressure already acting on the fluid surface. For absolute pressure, add the surface pressure: Pabsolute = Psurface + ρgh.

Worked Example

Using the calculator’s default values—water density 1,000 kg/m³, depth 10 m, and gravity 9.80665 m/s²:

  1. Apply the formula: ΔP = ρgh.
  2. Substitute the values: ΔP = (1,000 kg/m³)(9.80665 m/s²)(10 m).
  3. Multiply: ΔP = 98,066.5 Pa.
  4. Convert to kilopascals: 98,066.5 Pa ÷ 1,000 = 98.0665 kPa, or 98.067 kPa to three decimal places.

The units reduce to kg/(m·s²), which is a pascal. This is the pressure increase caused by ten metres of water, not the total absolute pressure.

Assumptions

  • The fluid is stationary, and its density is uniform from the surface to the point measured.
  • Depth means vertical distance below the fluid surface, not distance along a sloping path.
  • Gravity is constant over the depth and uses the entered value; 9.80665 m/s² is the standard value near Earth’s surface.
  • The calculated result is gauge pressure relative to the surface. Add surface pressure when absolute pressure is needed.

How Hydrostatic Pressure Changes with Depth

A fluid has weight, and the fluid above a point presses on the material below it. In a stationary fluid, that weight produces a pressure increase with depth. The equation follows from balancing the weight of a fluid column against the area supporting it: a column of area A and height h has volume Ah, mass ρAh, and weight ρAhg. Dividing that force by area gives pressure ρgh.

For a uniform fluid, pressure increases linearly with depth. At twice the depth, the pressure increase is twice as large; doubling density or gravitational acceleration has the same proportional effect. This relationship applies to liquids and to gases when density can reasonably be treated as constant. For a deep or strongly compressed gas, density may vary substantially with height, so a more detailed model is needed.

Pressure at a given depth in a connected, stationary fluid depends on vertical depth and density—not on the container’s shape or the total amount of fluid elsewhere in the container. A narrow vessel and a wide tank can therefore have the same pressure at the same depth if the fluid and gravity are the same.

Gauge Pressure and Absolute Pressure

Gauge pressure describes pressure above a reference pressure, commonly atmospheric pressure at the surface. The expression ρgh gives that increase for an open container whose surface is exposed to the atmosphere. Absolute pressure is measured from a vacuum and includes the surface pressure. Under ordinary open-air conditions, a useful relation is:

Absolute pressure ≈ atmospheric pressure + gauge pressure.

For example, the default calculation gives a gauge increase of 98.067 kPa. If the surface is open to the atmosphere, absolute pressure at ten metres is that increase plus the actual atmospheric pressure at the site. Atmospheric pressure changes with weather and elevation, so use a measured or appropriate local value when accuracy matters. If the fluid surface is sealed or pressurized, use the pressure at that surface instead of assuming atmospheric pressure.

Choosing Density and Depth

Density is material- and condition-dependent. Water is often approximated as 1,000 kg/m³ for simple calculations, but its density changes with temperature and dissolved substances. Seawater is denser than fresh water, and oils or other liquids can differ substantially. Use a density appropriate to the fluid and its temperature when the estimate needs to be precise; do not treat the default as universal.

  • Use density in kg/m³. If a source gives g/cm³, multiply by 1,000 to convert to kg/m³.
  • Use depth in metres. Convert centimetres to metres by dividing by 100, and feet to metres by multiplying by 0.3048.
  • Measure depth vertically from the fluid surface to the point where pressure is being considered.
  • Choose gravity appropriate to the location when necessary. For routine near-Earth estimates, 9.80665 m/s² is a standard reference value.

In a layered liquid with different densities, the pressure increase is the sum of each layer’s contribution: ΔP = g(ρ1h1 + ρ2h2 + …). A single average density can be used only if it correctly represents the total mass per volume over the depth being considered.

Common Mistakes and Limits

A frequent error is mixing units—for instance, entering density in g/cm³ as though it were kg/m³. Another is using the full distance through a pipe or down a slope instead of the vertical depth. The formula also does not calculate pressure caused by flow, pumps, impacts, or other dynamic effects; it describes the hydrostatic contribution in a stationary fluid.

Do not confuse pressure with force. Pressure is force per unit area: one pascal equals one newton per square metre. To find the force on a flat area under uniform pressure, use force = pressure × area, while accounting for the relevant pressure difference and the geometry. For a submerged object extending across a range of depths, pressure is not uniform over its surface, so a single pressure value may not describe the total load.

Use the result as a model-based estimate, not as a structural or engineering certification. The equation assumes a stable fluid and known density; waves, acceleration, temperature changes, compressibility, and local pressure variations can require additional analysis. For equipment or structures exposed to pressure, use appropriate design standards and qualified technical guidance.

Frequently Asked Questions

What is the pressure density depth formula?
It is ΔP = ρgh, where pressure increase is density times gravitational acceleration times vertical depth. The output is a pressure difference, commonly expressed in pascals.

How much pressure does water add per metre of depth?
With density 1,000 kg/m³ and gravity 9.80665 m/s², water adds about 9,806.65 Pa, or 9.807 kPa, per metre. Actual values vary slightly with water density and gravity.

Does the formula give gauge pressure or absolute pressure?
It gives gauge pressure: the increase relative to the pressure at the surface. Add the surface pressure to obtain absolute pressure.

Does container shape affect pressure at a given depth?
No, not for a stationary fluid of uniform density. Pressure at a point depends on the vertical depth, density, gravity, and pressure at the surface—not on the container’s shape.

Can I use this formula for air or another gas?
Yes, if density is approximately constant over the height considered. For tall columns or large pressure changes, gas density can vary with height, and the constant-density formula may not be accurate.

Related

Formula used
in rho | Fluid density | kg/m^3 | 1000 | 0
in h | Depth below surface | m | 10 | 0
in g | Gravitational acceleration | m/s^2 | 9.80665 | 0
out dp | Pressure increase | Pa | rho * g * h | 0
out kpa | Pressure increase | kPa | dp / 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →