molecalculator

Moles & Molar Mass

Hydrostatic Pressure: Density × Gravity × Height

Calculator No. 01-2137 · Updated · Formula and assumptions shown below

Gauge pressure 98,066 Pa
Gauge pressure
98.067 kPa
= Gauge pressure ÷ 1000
Fluid density
1000 kg/m^3
Set in the form below
Gravitational acceleration
9.80665 m/s^2
Set in the form below
You enter
Fluid density (kg/m^3), Gravitational acceleration (m/s^2), Vertical depth (m)
You get
Gauge pressure (Pa), Gauge pressure (kPa)
Rounding
0 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Yes: the gauge pressure in a stationary fluid is pressure = density × gravitational acceleration × depth, or p = ρgh. This page’s calculator uses fluid density, gravity, and vertical depth to find that pressure in pascals; it also reports the equivalent pressure in kilopascals.

Formula

The hydrostatic gauge-pressure formula is p = ρgh. Here, p is pressure relative to the surrounding pressure, measured in pascals (Pa); ρ is the fluid’s mass density in kilograms per cubic metre (kg/m3); g is gravitational acceleration in metres per second squared (m/s2); and h is vertical depth below the fluid surface in metres (m). The units combine as (kg/m3)(m/s2)(m) = kg/(m·s2) = Pa.

The second calculator output is the same pressure expressed in kilopascals: pkPa = p / 1000, because 1 kPa = 1000 Pa. The expression assumes the entered density and gravitational acceleration remain constant over the depth.

Worked Example

Using the calculator’s default values—density 1000 kg/m3, gravity 9.80665 m/s2, and depth 10 m:

  1. Apply the formula: p = ρgh.
  2. Substitute the inputs: p = (1000 kg/m3)(9.80665 m/s2)(10 m).
  3. Multiply: p = 98,066.5 Pa.
  4. Convert to kilopascals: 98,066.5 Pa / 1000 = 98.0665 kPa, which rounds to 98.067 kPa.

The headline result is therefore 98,067 Pa when displayed to zero decimal places. This is the pressure increase due to the water column, not the total absolute pressure.

Assumptions

  • The fluid is stationary, with constant density throughout the depth.
  • Gravitational acceleration is constant; 9.80665 m/s2 is the standard value used for this example.
  • Depth means vertical distance below the free surface, not distance along a sloped container or pipe.
  • The reported pressure is gauge pressure, measured relative to pressure at the fluid surface.

What the Equation Means

Pressure is force spread over an area. In a fluid at rest, deeper layers support the weight of the fluid above them. The deeper the point, the greater the weight per unit area, which is why pressure rises linearly with depth when density and gravity are constant.

The equation describes a pressure difference. At a free surface exposed to air, pressure is already atmospheric. To get absolute pressure at depth, add the pressure at the surface:

Absolute pressure = surface pressure + ρgh.

For an open container at sea level, surface pressure is approximately one standard atmosphere, 101.325 kPa. Thus, the example’s absolute pressure at 10 m in water is about 199.4 kPa, using that approximate surface pressure. Actual atmospheric pressure changes with weather and altitude. In a sealed vessel, use the actual pressure at the fluid surface, not automatically atmospheric pressure.

When to Use It and How to Read the Result

Use p = ρgh when estimating the pressure increase caused by a stationary liquid column. It is useful for understanding water pressure at depth, comparing fluid columns, or estimating pressure at the bottom of a tank. The output is pressure at the specified depth relative to the surface pressure.

  • At 1 m depth in fresh water, with density near 1000 kg/m3 and standard gravity, gauge pressure is about 9.81 kPa.
  • At 10 m depth under the same assumptions, it is about 98.1 kPa—roughly one atmosphere of additional pressure.
  • For the same fluid and gravity, doubling depth doubles the gauge pressure.
  • For the same depth and gravity, a denser fluid produces a proportionally larger pressure increase.

Water density depends on temperature, salinity, and pressure. The default 1000 kg/m3 is a convenient approximation for fresh water, not an exact value under every condition. For accurate work, use a density appropriate to the fluid and its conditions.

Common Misconceptions and Limits

Pressure is not simply density times height. The gravity factor is essential for converting fluid mass per volume into weight per area. Also, the formula gives the pressure increase, not necessarily the total pressure. Confusing gauge pressure with absolute pressure is a common source of errors.

The depth is the vertical height of fluid above the point. A vessel’s shape does not directly alter pressure at a given depth: a narrow column and a wide tank containing the same fluid can have the same pressure at equal depths. Their total forces on surfaces can differ because the areas differ.

The simple equation needs adjustment when density changes substantially with depth, as can happen in compressible gases or under large pressure changes. It also does not account for moving fluids, pump effects, frictional losses in pipes, or pressure changes from flow. Those situations require additional fluid-mechanics relationships.

For bench or field work, follow your method, the relevant safety information, and your supervisor’s instructions. Pressure calculations do not replace equipment ratings or appropriate engineering checks.

Frequently Asked Questions

Does pressure equal density times gravity times height?
For a stationary fluid of constant density, ρgh gives the pressure increase below its surface. It is gauge pressure; add surface pressure to find absolute pressure.

What units should I use for ρgh?
Use density in kg/m3, gravity in m/s2, and vertical depth in metres. The result is pascals. Divide by 1000 to express it in kilopascals.

How much does pressure increase per metre underwater?
In fresh water near 1000 kg/m3, the increase is about 9.8 kPa per metre at standard gravity. The exact value varies with water density and local gravity.

Is ρgh gauge or absolute pressure?
It is gauge pressure: the increase relative to the pressure at the fluid surface. Absolute pressure equals that increase plus the surface’s absolute pressure.

Does the shape of a tank affect pressure at its bottom?
Not at a given vertical depth if the fluid is stationary and has the same density. The shape can affect the total force on a bottom or wall because force also depends on surface area.

Related

Formula used
in rho | Fluid density | kg/m^3 | 1000 | 0
in g | Gravitational acceleration | m/s^2 | 9.80665 | 0
in h | Vertical depth | m | 10 | 0
out p | Gauge pressure | Pa | rho * g * h | 0
out pk | Gauge pressure | kPa | p / 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →