molecalculator

Moles & Molar Mass

Pressure Given Density: Formula and Calculator

Calculator No. 01-2140 · Updated · Formula and assumptions shown below

Gauge pressure increase 98,066.50 Pa
Gauge pressure increase
98.067 kPa
= Gauge pressure increase ÷ 1000
Fluid density
1000 kg/m^3
Set in the form below
Gravitational acceleration
9.80665 m/s^2
Set in the form below
You enter
Fluid density (kg/m^3), Gravitational acceleration (m/s^2), Depth below surface (m)
You get
Gauge pressure increase (Pa), Gauge pressure increase (kPa)
Rounding
2 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Pressure cannot be determined from density alone: a pressure calculation also needs information such as depth, height, temperature, or the forces and geometry involved. For a stationary fluid, this calculator finds the pressure increase with depth from the fluid’s density, gravitational acceleration, and depth; it returns pressure in pascals (Pa).

Formula

For a stationary fluid of constant density, the pressure increase between the surface and a point below it is:

ΔP = ρgh

  • ΔP is the pressure increase, or gauge pressure relative to the fluid surface, in pascals (Pa).
  • ρ (rho) is the fluid density in kilograms per cubic metre (kg/m³).
  • g is gravitational acceleration in metres per second squared (m/s²). The default, 9.80665 m/s², is the conventional standard-gravity value.
  • h is vertical depth below the surface in metres (m).

The second output converts pascals to kilopascals: 1 kPa = 1,000 Pa. This equation gives a pressure difference, not automatically the absolute pressure. To obtain absolute pressure, add the pressure at the fluid surface; for a tank open to the atmosphere, that is local atmospheric pressure.

Worked Example

Using the calculator’s default values—water density 1,000 kg/m³, gravitational acceleration 9.80665 m/s², and depth 10 m:

ΔP = ρgh

ΔP = (1,000 kg/m³)(9.80665 m/s²)(10 m)

ΔP = 98,066.5 Pa, which rounds to 98,066.50 Pa at the calculator’s two decimal places.

In kilopascals, 98,066.5 Pa / 1,000 = 98.0665 kPa, or 98.067 kPa at three decimal places. This is the pressure increase due to the 10 m water column, not the total absolute pressure.

Assumptions

  • The fluid is stationary; flow-related pressure changes are excluded.
  • Density is constant throughout the stated depth.
  • Depth means vertical distance below the fluid surface, not distance along a sloping path.
  • Gravity is treated as constant over the depth.
  • The result is gauge pressure increase. Surface pressure must be added if absolute pressure is required.

Why Density Alone Does Not Give Pressure

Density describes mass per unit volume. Pressure describes force per unit area. The two quantities are connected in a fluid because the fluid above a point has weight, but the amount of fluid above that point matters too. In the hydrostatic equation, density is multiplied by both gravitational acceleration and vertical depth.

For example, the same fluid at the same location produces twice the hydrostatic pressure increase at twice the depth. A denser liquid produces a greater increase than a less dense liquid at the same depth. But without depth and gravity, density by itself does not specify a pressure.

Pressure can also be related to density in other settings, but those relationships require different information. For an ideal gas, for example, pressure depends on density, temperature, and the gas’s specific gas constant. There is no single universal conversion from density to pressure that applies to liquids, gases, and solids alike.

Gauge Pressure, Absolute Pressure, and Units

Gauge pressure is measured relative to the surrounding pressure, commonly atmospheric pressure. Absolute pressure is measured from a vacuum. A pressure gauge reading of zero usually means the pressure matches the local atmosphere; it does not mean there is no pressure. For an open water tank, the hydrostatic result at a depth is the gauge pressure increase, and atmospheric pressure is present at the surface.

The calculator reports Pa and kPa. Other common pressure units include bar, atmospheres (atm), and pounds per square inch (psi). Convert units consistently rather than inserting a density in kg/L or a depth in centimetres while treating them as kg/m³ and metres. Useful conversions include 1 kg/L = 1,000 kg/m³ and 1 cm = 0.01 m. A mismatch of units can change the answer by factors of 10, 100, or 1,000.

When the Simple Formula Needs More Detail

The equation ΔP = ρgh is appropriate for a static fluid with uniform density. If density changes significantly with depth, pressure increase is found by accounting for the density at each level: in calculus, ΔP = ∫ρ(z)g dz over the vertical interval. This matters in situations such as a strongly stratified fluid or a gas column where density varies with altitude.

In a flowing system, pressure may also be affected by velocity, elevation changes, friction, pumps, and restrictions. The hydrostatic formula alone does not predict the full pressure at a point in a pipe. Likewise, pressure inside a sealed vessel can include gas pressure applied at the surface; add that boundary pressure when calculating absolute pressure in the fluid.

For a liquid whose density is known only approximately, the pressure result is approximate too. Temperature and composition can affect density. Use a value appropriate to the fluid and conditions when precision matters, and state whether the pressure is gauge or absolute so the number is not misinterpreted.

Frequently Asked Questions

Can you calculate pressure from density alone?
No. For a stationary fluid, you also need the vertical depth and gravitational acceleration. Other physical situations need their own additional variables.

What is the formula for pressure from density and depth?
The hydrostatic pressure increase is ΔP = ρgh, where density is in kg/m³, gravity in m/s², and depth in metres. The result is in pascals.

Is ρgh gauge pressure or absolute pressure?
It gives the pressure increase relative to the fluid surface. If the surface is exposed to the atmosphere, add atmospheric pressure to get absolute pressure.

Does water pressure increase linearly with depth?
For water of approximately constant density and constant gravity, yes: doubling the vertical depth doubles the hydrostatic pressure increase.

Does density determine pressure in a gas?
Not by itself. For an ideal gas, pressure also depends on temperature and the gas’s specific gas constant; the liquid-column formula is not a general gas equation.

What happens if density varies with depth?
The simple formula using one density is an approximation. Calculate the pressure change by integrating density times gravity over the vertical depth, or use an appropriate layered-fluid calculation.

Related

Formula used
in rho | Fluid density | kg/m^3 | 1000 | 0
in g | Gravitational acceleration | m/s^2 | 9.80665 | 0
in h | Depth below surface | m | 10 | 0
out dp | Gauge pressure increase | Pa | rho * g * h | 2
out pkpa | Gauge pressure increase | kPa | dp / 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →