molecalculator

Moles & Molar Mass

Radial Thermal Expansion Calculator: How It Works

Calculator No. 01-8866 · Updated · Formula and assumptions shown below

Change in radius 0.0600 mm
New radius
50.0600 mm
= Original radius × (1 + Coefficient of linear expansion × Temperature change)
Original radius
50 mm
Set in the form below
Temperature change
100 K
Set in the form below
You enter
Original radius (mm), Temperature change (K), Coefficient of linear expansion (1/K)
You get
Change in radius (mm), New radius (mm)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A radial thermal expansion calculator determines how much the radius (or diameter) of a circular object—such as a pipe, ring, or disk—changes when its temperature changes. You enter the original radius, the temperature change, and the material’s coefficient of linear thermal expansion, and the calculator returns the new radius and the change in radius.

Formula

The radial expansion of a circle follows the same linear expansion law that applies to any length dimension. The change in radius is given by:

Δr = r₀ × α × ΔT

where:

  • Δr = change in radius (mm, or any length unit)
  • r₀ = original radius (same unit as Δr)
  • α = coefficient of linear thermal expansion (1/K or 1/°C)
  • ΔT = temperature change (K or °C, since a difference is the same in both scales)

The new radius is simply r₀ + Δr, or equivalently r₀ × (1 + α × ΔT). This approximation is excellent for most engineering materials over moderate temperature ranges because α is very small (typically 10⁻⁶ to 10⁻⁵ per K).

Worked Example

Using the default values: a steel ring with an original radius of 50 mm, heated by 100 K, with α = 12 × 10⁻⁶ /K (typical for mild steel).

Step 1: Multiply the original radius by the coefficient:

50 mm × 12 × 10⁻⁶ /K = 0.0006 mm/K

Step 2: Multiply by the temperature change:

0.0006 mm/K × 100 K = 0.06 mm

So the radius increases by 0.06 mm. The new radius is 50 mm + 0.06 mm = 50.06 mm.

Check with the calculator: dr = 50 × 0.000012 × 100 = 0.06 mm, rnew = 50 × (1 + 0.000012 × 100) = 50.06 mm. The results match.

Assumptions

  • The material is isotropic: it expands equally in all directions.
  • The temperature change is uniform throughout the object (no thermal gradients).
  • The coefficient α is constant over the temperature range (in reality, α varies slightly with temperature, but the variation is small for many materials).
  • The object is free to expand—no external constraints that would induce stress.
  • The expansion is small enough that the linear approximation holds (true for most solids below their melting point).

Background: Why Radial Expansion Matters

When a solid is heated, its atoms vibrate more and take up more space, causing the material to expand in all dimensions. For a circular object, the radius and diameter increase proportionally to the linear expansion coefficient. This is why engineers must account for thermal expansion in pipes, railway tracks, bridges, and electronic components. For example, a steel pipe carrying hot steam will lengthen and its diameter will grow slightly; if the pipe is rigidly fixed, the resulting thermal stress can cause buckling or failure.

The same principle applies to holes: a hole in a metal plate expands when heated, just as a solid disk of the same material would. This is why a bearing ring heated on a shaft will fit more loosely, and why a cooled shaft (contracted) can be inserted into a hole that is slightly smaller at room temperature.

How to Choose the Coefficient of Thermal Expansion

The coefficient α is a material property. It is usually given in units of 1/°C or 1/K (the numerical value is identical because a 1°C change equals a 1 K change). Common values at room temperature:

  • Aluminum: ~23 × 10⁻⁶ /K
  • Steel (mild): ~12 × 10⁻⁶ /K
  • Stainless steel: ~16 × 10⁻⁶ /K
  • Copper: ~17 × 10⁻⁶ /K
  • Glass (borosilicate): ~3.3 × 10⁻⁶ /K
  • Concrete: ~10 × 10⁻⁶ /K

These values are approximate and vary with alloy composition and temperature. For precise work, consult the material datasheet. If you are dealing with a composite or anisotropic material (like carbon fiber), the expansion may differ in different directions, and a simple scalar α is not sufficient.

Common Mistakes and Misconceptions

One frequent error is confusing the coefficient of linear expansion (α) with the coefficient of area expansion (γ) or volume expansion (β). For isotropic materials, γ ≈ 2α and β ≈ 3α. For radial expansion, you must use α, not β. For example, using β for a steel pipe would give an answer three times too large.

Another mistake is using the wrong temperature scale. Since ΔT is a difference, 1°C = 1 K, so you can use either, but you must not add 273.15. For absolute temperatures (like in gas law calculations), you need Kelvin, but for expansion, only the difference matters.

A common misconception is that a hole shrinks when the surrounding material expands. Actually, the hole expands with the material. Imagine drawing a circle on a rubber sheet and then stretching the sheet uniformly: the circle gets larger. The same happens with a hole in a metal plate when heated.

Also, note that the calculator gives the change in radius. If you need the change in diameter, simply double the result. Similarly, the change in circumference is ΔC = C₀ × α × ΔT, which is proportional to the radius change.

Limits of the Simple Formula

The linear formula Δr = r₀ α ΔT is an approximation that holds for small expansions. Over very large temperature changes, α itself changes, and the expansion becomes nonlinear. For most engineering applications (temperature changes of a few hundred kelvin), the error is negligible. However, for cryogenic applications or materials near their melting point, you should use more accurate models that integrate α(T) over the temperature range.

Another limit: the formula assumes the object is free to expand. If the object is constrained, thermal stresses develop, and the actual deformation may be less than the free expansion. In such cases, you need a stress analysis, not just a simple expansion calculation.

Practical Applications and Examples

Here are a few real-world situations where radial expansion calculations are used:

  • Pipe systems: A 100 mm diameter steel pipe carrying steam at 150°C above ambient expands in radius by about 0.09 mm (using α=12e-6). This small change is enough to require expansion loops or joints.
  • Shrink fits: To fit a steel bushing (outer radius 25 mm) into a hole that is 0.02 mm smaller, you can heat the bushing by ΔT = 0.02 / (25 × 12e-6) ≈ 67 K. The bushing expands enough to slide in, and when it cools, it grips tightly.
  • Rotating machinery: A turbine disk operating at high temperature will grow radially. Clearance between the blade tips and the casing must account for this growth to prevent rubbing.
  • Electronic components: Solder joints and lead frames expand when powered on. Mismatched expansion coefficients can cause thermal fatigue over many cycles.

For a quick estimate, remember that a 1 meter steel rod expands about 0.012 mm per 1°C. For a radius of 1 meter, the radial expansion is the same number (0.012 mm per °C).

Frequently Asked Questions

Does the hole in a metal plate expand or shrink when heated?

The hole expands, just like the material around it. The expansion is isotropic, so all dimensions increase proportionally. If the plate is free to expand, the hole’s radius increases by the same factor as the plate’s outer radius.

What is the difference between linear, area, and volume expansion coefficients?

The linear coefficient α describes how a single length changes. The area coefficient γ describes how an area changes (γ ≈ 2α), and the volume coefficient β describes how a volume changes (β ≈ 3α). For radial expansion, use α, not the others.

Can I use this calculator for a cylinder’s radius?

Yes, for a solid cylinder or a hollow cylinder (pipe), the radial expansion is the same as for a disk of the same material. The length also expands, but that is a separate calculation. The formula applies to any circular cross-section.

What units should I use for the coefficient?

The coefficient is typically expressed in 1/°C or 1/K. Since a temperature difference is the same in both scales, you can use either. The calculator expects the coefficient in 1/K, but the numerical value is identical to 1/°C.

Is the expansion the same for all steels?

No, different steel alloys have different coefficients. For example, austenitic stainless steels (like 304) have a coefficient around 16-17 × 10⁻⁶ /K, while ferritic steels are around 11-12 × 10⁻⁶ /K. Always use the specific value for your material.

How do I account for a temperature change that is not uniform?

The simple formula assumes a uniform temperature change. If the temperature varies across the object, the expansion will be non-uniform, leading to thermal stresses. For accurate analysis, you would need finite element analysis or a more complex calculation.

Related

Formula used
in r | Original radius | mm | 50 | 0
in dt | Temperature change | K | 100 | 0
in a | Coefficient of linear expansion | 1/K | 0.000012 | 0
out dr | Change in radius | mm | r * a * dt | 4
out rnew | New radius | mm | r * (1 + a * dt) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →