molecalculator

Moles & Molar Mass

Radius From Arc and Chord Length Calculator

Calculator No. 01-2805 · Updated · Formula and assumptions shown below

Radius 1.0000 same units
Central angle
1.5708 radians
= Arc length ÷ Radius
Central angle
90.00 degrees
Result, rounded to 2 decimal places
Arc length
1.570796327 same units
Set in the form below
You enter
Arc length (same units), Chord length (same units)
You get
Radius (same units), Central angle (radians), Central angle (degrees)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Use this calculator to find a circle’s radius from the length of an arc and its corresponding chord. Enter both lengths in the same unit; the calculator returns the radius in that unit, along with the central angle in radians and degrees.

Formula

For an arc of length a and its chord of length c, the radius r satisfies:

c = 2r sin(a / (2r))

Because the radius occurs both outside and inside the sine function, this equation generally cannot be rearranged into a simple elementary formula for r. The calculator solves it numerically for the minor arc, where 0 < a/r ≤ π. Its outputs are:

  • r: radius, in the same length unit used for both inputs.
  • θ: central angle in radians, calculated as θ = a/r.
  • d: central angle in degrees, calculated as d = θ × 180/π.

The inputs must describe the same circle segment and use consistent units. A valid minor arc has a chord no longer than its arc, and its chord is no greater than the diameter. The minor-arc convention is important: an arc longer than a semicircle needs additional information to identify which arc is intended.

Worked Example

The defaults use an arc length of 1.570796327 units and a chord length of 1.414213562 units. These are approximately π/2 and √2, corresponding to a 90-degree arc on a circle of radius 1.

  1. Start with c = 2r sin(a/(2r)). Substitute the default values: 1.414213562 = 2r sin(1.570796327/(2r)).
  2. The numerical minor-arc solution is r ≈ 1.0000. Checking the relationship, 2 × 1.0000 × sin(1.570796327/(2 × 1.0000)) ≈ 1.414213562.
  3. Calculate the angle in radians: θ = a/r = 1.570796327/1.0000 = 1.5708 radians.
  4. Convert to degrees: d = 1.570796327 × 180/π ≈ 90.00°.

Thus, the radius is 1.0000 length units. The equation is nonlinear, so the radius step requires numerical solving rather than ordinary algebraic rearrangement.

Assumptions

  • The arc and chord belong to the same circle and describe the same pair of endpoints.
  • The requested arc is the minor arc, or a semicircle; the corresponding central angle is at most 180 degrees.
  • Both lengths are positive and expressed in the same unit.
  • Measurements are treated as exact for calculation; real measurement uncertainty is not included in the displayed result.

How Arc and Chord Length Determine Radius

A chord is the straight line between two points on a circle. An arc is the curved portion of the circumference between those same points. Their lengths together indicate how sharply the circle bends: for a fixed chord, a shorter arc means a larger, flatter circle, while an arc closer in length to the chord means a smaller radius.

Imagine drawing two radii from the circle’s center to the chord’s endpoints. They form an isosceles triangle with side lengths r, r, and c. The angle at the center is θ. The arc-length relationship is a = rθ, and the triangle’s chord relationship is c = 2r sin(θ/2). Substituting θ = a/r gives the calculator’s equation.

This also explains why a direct formula is not usually available: the unknown radius affects both the scale of the triangle and the angle inside the sine. A numerical method tries candidate radii until the chord predicted by the equation matches the entered chord.

When to Use the Minor-Arc Formula

This method applies when you know the curved distance along a circular arc and the straight-line distance between its endpoints. It can be useful for estimating the radius of a circular feature from a measured segment, checking a drawing, or solving a geometry problem. It does not apply directly to an arbitrary curve, an ellipse, or measurements taken from different circles.

The arc and chord should refer to the same endpoints. For example, measuring a chord across one feature and an arc around a different portion of the boundary does not provide a valid pair. If the curve is only approximately circular, the result is an estimated radius that depends on how accurately the chosen segment follows a circle.

Common Measurement and Interpretation Problems

  • Mixing units: If the arc is measured in centimetres and the chord in millimetres, convert one before calculating. The output uses the unit shared by the inputs.
  • Using an arc longer than its chord: For a genuine circular segment, arc length cannot be shorter than the straight chord. If it is, check the measurements, units, or endpoint selection.
  • Confusing minor and major arcs: Two endpoints define a minor arc and a major arc. The same chord can correspond to either; the minor-arc calculation assumes the arc is at most a semicircle.
  • Rounding too early: Small rounding differences in measured lengths can affect the inferred radius, especially when the arc and chord are close together. Keep the original precision during calculation and round only the final result to a precision justified by the measurements.
  • Expecting a unique answer from one length alone: A chord by itself does not determine a radius; many circles can pass through its endpoints. The arc length supplies the additional information needed under the circular-arc assumption.

Limits and a Useful Approximation

When the arc is very short compared with the radius, the arc and chord are nearly equal. Their small difference can be difficult to measure reliably, so the calculated radius may be highly sensitive to measurement error. A calculator can solve the equation, but it cannot make uncertain measurements precise.

For a short arc, a useful approximation is r ≈ √(a³/[24(a − c)]). It follows from approximating the small-angle sine relationship and is most useful when a and c are close and the minor arc is small. It is not a replacement for solving the full equation when accuracy matters, and it becomes unreliable if measurement error makes a − c tiny or nonpositive.

At the other limit, a semicircle has θ = π radians, so its arc length is a = πr and its chord is the diameter c = 2r. Therefore, for a known semicircular arc, r = a/π = c/2. That special case has a direct solution; most other arc-and-chord pairs require numerical solving.

Frequently Asked Questions

What is the formula for radius from arc length and chord length?
The relationship is c = 2r sin(a/(2r)), where a is arc length, c is chord length, and r is radius. Since r appears inside and outside the sine, solve it numerically in the general case.

Can I calculate the radius from chord length alone?
No. A given chord can fit circles of many different radii. You also need information such as the corresponding arc length or central angle.

Does the calculator work for a major arc?
It uses the minor arc, with a central angle no greater than 180 degrees. A major arc requires identifying the intended sweep and supplying enough information to distinguish it; do not assume the minor-arc result describes it.

What if the arc length is equal to the chord length?
For a finite circle, a nonzero arc is longer than its chord. Equality is approached as the arc becomes extremely short relative to the radius, so equal measured values may indicate rounding or insufficient measurement precision rather than a finite, exact radius.

Why is the radius not calculated with a simple rearrangement?
The unknown radius determines the central angle a/r, which is then inside a sine function, while also multiplying that sine. This combination generally requires a numerical solution, except in special cases such as a semicircle.

Related

Formula used
in a | Arc length | same units | 1.570796327 | 0
in c | Chord length | same units | 1.414213562 | 0
out r | Radius | same units | 1.000000000 | 4
out t | Central angle | radians | a / r | 4
out d | Central angle | degrees | t * 180 / pi | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →