molecalculator

Moles & Molar Mass

Radius From Chord and Height: Formula and Calculator

Calculator No. 01-2809 · Updated · Formula and assumptions shown below

Circle radius 72.50 mm
Circle diameter
145.00 mm
= 2 × Circle radius
Chord length
100 mm
Set in the form below
Sagitta (height)
20 mm
Set in the form below
You enter
Chord length (mm), Sagitta (height) (mm)
You get
Circle radius (mm), Circle diameter (mm)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Calculate the radius of a circle from a chord’s length and the sagitta, or height, measured from the chord to the arc. Enter both lengths in the same unit to get the circle’s radius in that unit; the calculation assumes the chord and height describe a circular arc.

Formula

The radius is r = (c² + 4h²) / (8h), equivalently r = c²/(8h) + h/2. Here, r is the circle’s radius, c is the straight-line chord length, and h is the sagitta: the perpendicular distance from the chord’s midpoint to the arc. All three quantities must use the same length unit. The optional diameter output is d = 2r.

This formula follows from a right triangle whose legs are half the chord, c/2, and the radius minus the sagitta, r − h; its hypotenuse is the radius. Thus (c/2)² + (r − h)² = r². Expanding and rearranging gives the radius expression above. The calculator uses the standard circular-segment formula and does not require a trigonometric angle.

Worked Example

Using the calculator’s default inputs, c = 100 mm and h = 20 mm:

  1. Square the chord: c² = (100 mm)² = 10,000 mm².
  2. Calculate four times the squared height: 4h² = 4 × (20 mm)² = 1,600 mm².
  3. Add the terms and calculate the denominator: c² + 4h² = 11,600 mm²; 8h = 160 mm.
  4. Divide: r = 11,600 mm² / 160 mm = 72.50 mm.
  5. The diameter is d = 2 × 72.50 mm = 145.00 mm.

Assumptions

  • The measured chord and sagitta belong to one circular arc.
  • The height is perpendicular to the chord and measured at its midpoint.
  • Both inputs use the same unit and are positive; the height is greater than zero.
  • The circular arc is the minor arc, or the measurements otherwise identify the intended segment.

What Chord and Height Mean

A chord is a straight segment joining two points on a circle. It is not the curved distance along the circumference between those points. The sagitta is the maximum gap between that straight chord and the arc, measured along the perpendicular through the chord’s midpoint. It is sometimes called the rise, depth, or segment height.

For a minor circular segment, the sagitta points toward the arc and is smaller than the radius. A shallow arc has a small sagitta relative to its chord; a more strongly curved arc has a larger sagitta. The same chord can therefore belong to circles of very different sizes depending on the measured height. A chord alone is not enough to determine a unique radius.

When This Calculation Is Useful

The relationship is useful when a curved edge is part of a circle and you can measure its straight span and rise. It can help estimate a radius for a circular arch, a curved panel, a pipe cross-section, or a machined circular feature. It is also useful when a drawing gives a chord and a segment depth but omits the radius.

To take measurements, identify the two ends of the same arc and measure the straight distance between them for the chord. Then locate the chord’s midpoint and measure perpendicularly from the chord to the arc for the sagitta. Measuring the height from an endpoint, along a sloping line, or to a different part of the curve does not match the formula’s definition.

For example, if a feature has a 100 mm chord and a 20 mm midpoint rise, the radius is 72.50 mm. That result does not say the arc length is 100 mm: the chord is straight, while arc length follows the curve. If arc length is what you need, it requires a separate calculation.

Choosing and Checking Measurements

The inputs should be taken from the same circular segment. If measurements come from a physical object, accuracy in the sagitta matters particularly when the arc is shallow: a small absolute error in a small height can cause a substantial change in the calculated radius.

  • Use consistent units. If the chord is 10 cm and the rise is 20 mm, convert one first: 10 cm is 100 mm. The output then uses millimetres.
  • Measure the midpoint rise. The sagitta is not the height at an arbitrary location along the chord.
  • Keep sensible precision. Avoid rounding measurements before calculating, especially a small sagitta. The displayed result is rounded to two decimal places, but that does not imply the original measurements were accurate to that precision.
  • Check the scale. For a minor arc, the radius should be at least half the chord, and the sagitta should not exceed the radius.

For measurements with known uncertainty, calculate a range using the plausible smallest and largest chord and height values. Reporting a radius with many decimal places cannot compensate for uncertain or poorly placed measurements.

Common Misconceptions and Limits

A frequent mistake is to treat the sagitta as the circle’s radius. They are different distances: the radius runs from the circle’s center to the arc, while the sagitta runs from the chord to the arc. Another is to put the chord length into a formula for arc length. The chord is a straight distance and is used as c in this equation.

The calculation also cannot confirm that a real edge is truly circular. A noncircular curve may share the same chord and midpoint rise but have a different shape between those measured points. Use additional measurements at other locations or a suitable curve-fitting method if the object may not be circular.

There is a geometric ambiguity if the endpoints and arc are not specified. Two endpoints define a minor arc and a major arc on the same circle. The standard sagitta measurement is usually taken for the segment bounded by the chord and the minor arc. If a measurement is intended to describe a major arc, make sure the height convention and chosen arc are clear; do not assume the same segment interpretation without checking the diagram or geometry.

Frequently Asked Questions

What is the formula for radius from chord and height?
Use r = (c² + 4h²)/(8h), where c is chord length and h is the perpendicular midpoint height, or sagitta. Use the same unit for both inputs.

Can I calculate a circle’s radius from the chord alone?
No. Many circles can pass through the same two chord endpoints. You need another measurement, such as the sagitta, to determine the radius.

Is chord height the same as arc height or sagitta?
In this calculation, yes: height means the perpendicular distance between the chord and the arc at the chord’s midpoint. It is also called the sagitta or rise.

What happens if the height is zero?
The formula divides by h, so zero height cannot be used. Geometrically, a perfectly straight line is the limiting case of a circle with an unbounded radius, not a finite-radius circular segment.

Can the height be greater than half the chord?
Yes. The height is not limited to half the chord. For a minor segment it must remain below the radius; if the measurements imply a different arc or segment, clarify which arc is being described.

Does the result give the arc length?
No. It gives the circle’s radius. Arc length is the distance along the curved edge and requires the radius together with the central angle, or another suitable measurement.

Related

Formula used
in c | Chord length | mm | 100 | 0
in h | Sagitta (height) | mm | 20 | 0
out r | Circle radius | mm | (c ^ 2 + 4 * h ^ 2) / (8 * h) | 2
out d | Circle diameter | mm | 2 * r | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →