This calculator finds a circle’s radius from a chord length and the perpendicular distance from the circle’s center to the chord. Enter both lengths in the same unit to get the radius in that unit; chord length alone is not enough to determine a unique radius.
Formula
A chord is a straight line segment joining two points on a circle. If its length is c and the perpendicular distance from the circle’s center to the chord is d, the radius is:
r = √[(c / 2)² + d²]
- r is the circle’s radius, in the same length unit as the inputs.
- c is the chord length.
- d is the perpendicular center-to-chord distance, sometimes called the sagitta’s complementary distance or the apothem of the chord.
The calculator also reports the diameter, D = 2r. The formula follows from a right triangle: the perpendicular from the center to a chord bisects the chord, so one leg is c/2, the other is d, and the hypotenuse is the radius. This is the Pythagorean theorem applied to the triangle.
Worked Example
Using the defaults, the chord is 6 m long and the perpendicular center-to-chord distance is 4 m. The perpendicular divides the chord into two equal halves:
c / 2 = 6 m / 2 = 3 m
r = √[(3 m)² + (4 m)²] = √(9 m² + 16 m²) = √25 m² = 5 m
Rounded to the calculator’s four decimal places, the radius is 5.0000 m. The diameter is 2 × 5 m = 10.0000 m.
Assumptions
- The chord and center-to-chord distance are measured in the same unit and refer to the same circle.
- The distance is perpendicular to the chord and is measured from the circle’s center, not from the arc or an endpoint.
- The inputs are positive lengths; the calculation assumes an ideal circular geometry.
Why Chord Length Alone Is Not Enough
A given chord length can occur in circles of many different radii. For example, a 6 m chord could be a diameter of a 3 m-radius circle, or a short chord in a much larger circle. The position of the chord relative to the center supplies the missing geometric information.
There is one special case: if you know the chord is a diameter, then the radius is simply half the chord length, r = c/2. Otherwise, you need another measurement, such as the center-to-chord distance, the central angle, or the sagitta (the arc’s height above the chord).
For a non-diameter chord in a circle, the center-to-chord distance is greater than zero and less than the radius. A zero distance means the line passes through the center; for a true chord in that case, it is the diameter.
Using Other Measurements
If you know the chord length and the central angle instead, the radius can be found with a different formula. For a central angle θ in radians:
r = c / [2 sin(θ / 2)]
For an angle in degrees, use the same relationship with the sine evaluated in degrees. Make sure the angle is the one subtended at the circle’s center, not an angle measured at a point on the circumference.
If you know the chord length c and the sagitta s—the perpendicular height from the chord to the arc—then:
r = c² / (8s) + s / 2
Here, s is measured from the chord to the arc along the perpendicular through the chord’s midpoint. This is not the same quantity as d, the distance from the center to the chord. For a minor arc, d = r − s; confusing the two measurements is a common source of incorrect results.
Measurement and Unit Checks
Use consistent units before entering values. If the chord is measured in centimetres and the center-to-chord distance in millimetres, convert one measurement first; for example, 1 cm = 10 mm. The formula combines squared lengths, so mixing units without conversion gives a meaningless result.
For real measurements, the calculated radius is only as reliable as the inputs. Small measurement errors can matter, especially when the chord is short compared with the circle or when the center-to-chord distance is estimated indirectly. Keep more digits during intermediate calculations, then round the final result to match the precision of the measurements. Reporting many decimal places does not make an imprecise measurement more accurate.
- Measure the chord straight between its endpoints, not along the curved arc.
- Locate the chord midpoint; the perpendicular from the center meets the chord there.
- Check that both lengths use the same units and that the distance is nonnegative.
- Compare the result with known geometry: the radius must be at least half the chord length.
Frequently Asked Questions
Can you find a radius from chord length alone?
No. Many circles can contain a chord of the same length. You also need a measurement or condition that fixes the chord’s position, such as its perpendicular distance from the center or its central angle.
What is the radius if the chord is the diameter?
The radius is half the diameter, so if the chord is known to pass through the center, use r = c/2. This special case has a center-to-chord distance of zero.
Is the center-to-chord distance the same as sagitta?
No. The center-to-chord distance runs from the center to the chord. Sagitta runs from the chord to the arc along the same perpendicular. For a minor arc, the radius equals the center-to-chord distance plus the sagitta.
What if my chord is longer than the diameter I expect?
A chord cannot be longer than its circle’s diameter, so the radius must be at least half the chord length. If your result conflicts with an independently known radius, recheck the units, endpoint measurements, and whether the distance was measured perpendicular to the chord.
Can the formula be used for a curved or irregular shape?
It applies to a circle, or to a circular arc when the chord and center-related measurement describe that same circle. It does not determine a single radius for a general irregular curve.
Related
Formula used
in c | Chord length | m | 6 | 0 in d | Center-to-chord distance | m | 4 | 0 out r | Radius | m | sqrt((c / 2)^2 + d^2) | 4 out D | Diameter | m | 2 * r | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Skip Calculator for Soil: What It Can and Can’t Do7.500 m³
- USD to KPW Calculator: Convert Dollars to North Korean Won90,000.00 KPW
- OK Calculator on TV on the Radio? Meaning Explained
- Pension Calculator KP: Estimate Your Pension Benefits
- Neonatal Kp Calculator: What It Means80.0000 mmol/mmol
- Newton to kp Converter Calculator and Formula1.0000 kp