molecalculator

Moles & Molar Mass

RCF to G: Convert Relative Centrifugal Force

Calculator No. 01-2242 · Updated · Formula and assumptions shown below

Relative centrifugal force 1,006 × g
Centrifugal acceleration
9,867.45 m/s²
= Relative centrifugal force × 9.80665
Rotor radius from axis to sample
10 cm
Set in the form below
Rotor speed
3000 rpm
Set in the form below
You enter
Rotor radius from axis to sample (cm), Rotor speed (rpm)
You get
Relative centrifugal force (× g), Centrifugal acceleration (m/s²)
Rounding
0 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

RCF is not a fixed equivalent of g: relative centrifugal force is already expressed as a multiple of standard gravity. For example, 1,000 × g means a centrifugal acceleration 1,000 times standard gravity; converting an RCF value into revolutions per minute (RPM) also requires the rotor radius.

Formula

The calculator uses the standard relationship between rotor speed, radius, and relative centrifugal force:

RCF = 1.118 × 10−5 × r × RPM2

  • RCF is relative centrifugal force, reported as a multiple of standard gravity (× g).
  • r is the distance in centimeters from the rotor’s axis of rotation to the sample’s relevant position.
  • RPM is rotor speed in revolutions per minute.

The coefficient incorporates the conversion from centimeters and minutes to acceleration units and divides by standard gravity, taken here as 9.80665 m/s². The second output converts the calculated multiple of g into acceleration: acceleration = RCF × 9.80665 m/s². RCF is a ratio, not a force measured in newtons.

Worked Example

With the default radius of 10 cm and speed of 3,000 rpm:

  1. Square the speed: 3,000² = 9,000,000 rpm².
  2. Apply the RCF formula: 1.118 × 10−5 × 10 × 9,000,000 = 1,006.2 × g.
  3. Convert to acceleration: 1,006.2 × 9.80665 = 9,867.85173 m/s², or 9,867.85 m/s² rounded to two decimal places.

Thus, at those settings the sample experiences approximately 1,006 × g. The calculator rounds the headline RCF to a whole number, so its display is 1,006 × g.

Assumptions

  • The radius is entered in centimeters, measured from the rotation axis to the sample position used for the intended RCF.
  • RPM is the rotor’s actual rotational speed, not a target force or a speed expressed in another unit.
  • The formula describes ideal circular motion and uses standard gravity, 9.80665 m/s², as the reference.
  • The result is an acceleration ratio; it does not account for sample density, viscosity, tube shape, or how long the rotor runs.

What RCF and g Mean

In centrifugation, “g” refers to the acceleration due to Earth’s gravity, approximately 9.80665 m/s². RCF, or relative centrifugal force, compares the centripetal acceleration at a point in a spinning rotor with that reference. A setting of 500 × g therefore means an acceleration 500 times standard gravity at the specified radius.

This is why the phrase “RCF equivalent to g” can be confusing. RCF is commonly written with a g multiplier, so an instruction such as “centrifuge at 2,000 g” usually means 2,000 × g RCF—not a speed in RPM and not a force in newtons. The word “centrifugal” is conventional in this context; in a rotating frame it describes the apparent outward effect, while the sample’s inward centripetal acceleration has the same magnitude.

How to Convert RCF to RPM

To find the RPM needed for a specified RCF, rearrange the formula:

RPM = √[RCF ÷ (1.118 × 10−5 × r)]

For example, to reach 1,000 × g at a radius of 10 cm:

RPM = √[1,000 ÷ (1.118 × 10−5 × 10)] = √8,944,543.828… ≈ 2,990.74 rpm.

That is approximately 2,991 rpm, subject to the instrument’s available settings and the exact radius convention. Because RPM is proportional to the square root of RCF, doubling the target RCF does not require doubling the speed. Conversely, doubling RPM produces four times the RCF if the radius stays constant.

Choosing the Correct Rotor Radius

Radius is the distance from the axis of rotation to the sample point—not the tube’s length or its distance from the center of the rotor housing. The appropriate point depends on the equipment and on how the protocol defines RCF. A sample can extend over a range of radii, so the force at its top and bottom may differ.

  • Fixed-angle rotor: sample positions lie at an angle, and protocols or rotor documentation may specify a maximum, average, or other effective radius.
  • Swinging-bucket rotor: the bucket changes position during rotation, so use the radius specified for the operating configuration and protocol.
  • Known RCF display: if a centrifuge displays × g directly, check whether its setting uses a stated or programmed rotor radius rather than assuming it matches another rotor.

For a reliable conversion, consult the rotor documentation and the method’s definition of radius. A small radius error produces a proportional RCF error: using a radius 10% too large gives a calculated RCF 10% too large at the same speed.

Common Conversion Mistakes and Limits

  • Mixing up RCF and RPM: neither value can be converted to the other without a rotor radius.
  • Entering millimeters as centimeters: convert millimeters to centimeters by dividing by 10 before using the formula.
  • Forgetting to square RPM: force changes with the square of speed, not in direct proportion.
  • Using the wrong radius: a rotor’s maximum radius may not be the radius used by a particular protocol or display.
  • Rounding too early: retain precision through the calculation, then round the final speed or RCF to a useful setting.

The equation gives a mechanical acceleration estimate, not a guarantee that two centrifuges will produce identical separation. Sample behavior also depends on factors such as particle size and density, liquid properties, rotor geometry, and run time. Follow the method, the equipment limits, and the applicable safety guidance; do not exceed a rotor’s rated speed.

Frequently Asked Questions

Is RCF the same as g?
RCF is expressed as a multiple of standard gravity. For instance, 1,000 × g is an acceleration 1,000 times standard gravity; it is not the same numerical quantity as RPM.

How many RPM is 1,000 × g?
There is no single RPM equivalent. It depends on radius: RPM = √[1,000 ÷ (1.118 × 10−5 × radius in cm)]. At 10 cm, that is about 2,991 rpm.

Can I convert RPM to RCF without the rotor radius?
No. The radius is required because RCF increases in direct proportion to radius at a given RPM.

Does doubling RPM double RCF?
No. With the same radius, RCF is proportional to RPM squared, so doubling RPM gives four times the RCF.

Why do two centrifuges show different RCF at the same RPM?
They may have different rotor radii. The RCF at a given speed is higher for the larger radius, and display conventions or selected rotor settings can also differ.

Related

Formula used
in r | Rotor radius from axis to sample | cm | 10 | 0.1
in rpm | Rotor speed | rpm | 3000 | 0
out rcf | Relative centrifugal force | × g | 1.118e-5 * r * rpm^2 | 0
out accel | Centrifugal acceleration | m/s² | rcf * 9.80665 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →