RCF in a centrifuge means relative centrifugal force: the acceleration produced by spinning, expressed as a multiple of standard gravity, or ×g. This calculator estimates RCF from rotor radius and speed in revolutions per minute (RPM), or calculates RPM from a target RCF and radius.
Formula
For a rotor turning at a steady speed, relative centrifugal force is:
RCF = 1.118 × 10−5 × r × RPM2
Here, r is the distance from the axis of rotation to the sample, in centimetres, and RPM is rotational speed in revolutions per minute. The calculator writes the same formula as 1.118 × r × (RPM / 1000)2. Its second output converts RCF to acceleration: a = RCF × 9.80665 m/s², using standard gravity, gn = 9.80665 m/s². RCF is a ratio, so it is commonly written as ×g; it is not a force in newtons.
The inverse formula for finding speed is RPM = √(RCF / (1.118 × 10−5 × r)). For example, at a radius of 10 cm, a target of 1,000 ×g corresponds to about 2,990 RPM. This calculator’s first output is RCF, so use the inverse equation separately when RPM is the unknown.
Worked Example
Using the default inputs, the rotor radius is 10 cm and speed is 5,000 RPM.
- Convert the speed term: 5,000 / 1,000 = 5.
- Square it: 52 = 25.
- Calculate RCF: 1.118 × 10 × 25 = 279.5 ×g.
- Convert to acceleration: 279.5 × 9.80665 = 2,741.959675 m/s², or 2,741.96 m/s² to two decimal places.
The calculator therefore returns 280 ×g when its RCF output is rounded to zero decimal places, and 2,741.96 m/s² for acceleration.
Assumptions
- The rotor turns at a constant speed, and the radius is measured from the rotation axis to the sample location being considered.
- The calculation uses the standard RCF approximation and standard gravity, 9.80665 m/s².
- The sample is treated as a point at the entered radius. In a swinging-bucket rotor, its distance from the axis changes as the bucket moves; use the radius specified for the protocol or rotor documentation.
RCF, RPM, and Rotor Radius
RPM tells you how fast the rotor turns. RCF tells you the resulting acceleration at a particular radius. The two values are related, but they are not interchangeable: the same RPM can produce different RCFs in rotors with different geometries. Conversely, the same RCF can be reached at different RPMs by changing the radius.
RCF rises in proportion to radius but in proportion to the square of RPM. Doubling the radius doubles RCF; doubling RPM makes RCF four times larger. That square relationship is why a modest speed change can substantially alter the force on a sample.
For instance, at 5,000 RPM, a radius of 10 cm gives about 280 ×g. At the same speed and a radius of 20 cm, the estimate is about 559 ×g. The calculation does not mean that every part of a tube experiences exactly that value: the radius varies from the inner to outer end of the sample. Protocols and rotor specifications may therefore identify whether RCF refers to the maximum, minimum, or a stated sample position.
How to Choose the Radius
Use the radius that matches the point in the rotor and sample named by your method. A rotor’s maximum radius is often measured from the axis to the bottom or outermost sample position, but conventions can differ. Check the rotor documentation or the protocol rather than assuming that the tube’s length, rotor diameter, or radius to its center is the correct value.
- Fixed-angle rotor: The sample sits at an angle, so the bottom of the tube is farther from the axis than its top. The force varies along the sample column.
- Swinging-bucket rotor: Buckets pivot outward during spinning. The relevant radius depends on the bucket’s operating position and the location within the sample.
- Protocol gives ×g: Enter the protocol’s target RCF into the inverse formula, using the radius specified for that rotor, to estimate the needed RPM.
If a protocol gives a speed for a different rotor, do not copy that RPM without checking. Convert the stated RCF using the radius of the rotor you will use, and confirm that the rotor and centrifuge are rated for the required speed.
Common Errors and Limits
- Using diameter instead of radius: If a dimension is given as a diameter, divide it by two before using it as a radius.
- Mixing units: This calculator requires radius in centimetres. Entering millimetres or metres as though they were centimetres gives a wrong result.
- Confusing RCF with RPM: RCF is an acceleration relative to gravity; RPM is rotational speed. They describe different quantities.
- Rounding too early: Keep the unrounded RCF while converting between RCF and RPM. Round only the reported result to the precision needed by the method.
- Assuming one radius describes the whole sample: A sample spans a range of radii, so the actual acceleration varies across it.
The formula estimates acceleration from radius and rotation rate; it does not predict whether a sample will pellet, how long separation takes, or what setting is suitable for a particular material. Those depend on the sample, rotor design, tube and protocol. Before operation, check the centrifuge and rotor limits, compatible vessels, balance requirements, and applicable safety instructions. Follow your lab method, the safety data sheet (SDS) and your supervisor.
Frequently Asked Questions
What does RCF stand for in a centrifuge?
RCF stands for relative centrifugal force. It expresses the acceleration at a sample’s location as a multiple of standard gravity, usually written ×g.
Is RCF the same as RPM?
No. RPM measures revolutions per minute; RCF measures acceleration relative to gravity. Converting between them requires the rotor radius.
How do I calculate RCF from RPM?
Use RCF = 1.118 × 10−5 × radius in cm × RPM². Make sure the radius is measured from the axis to the sample location of interest.
How do I convert RCF to RPM?
Use RPM = √(RCF / (1.118 × 10−5 × radius in cm)). Confirm that the resulting speed is permitted for the rotor and centrifuge.
Why does the same RPM give a different RCF?
Because RCF depends on both speed and radius. At the same RPM, a sample farther from the axis experiences greater acceleration.
Should I use the rotor’s maximum radius?
Use the radius specified by the procedure or rotor documentation. The maximum radius may be appropriate for some conventions, but the required sample position depends on how the method defines its RCF.
Related
Formula used
in r | Rotor radius | cm | 10 | 0 in rpm | Speed | rpm | 5000 | 0 out rcf | Relative centrifugal force | ×g | 1.118 * r * (rpm / 1000)^2 | 0 out g | Acceleration | m/s² | rcf * 9.80665 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %