molecalculator

Moles & Molar Mass

Reaction Rate Formula Variables Explained

Calculator No. 01-11997 · Updated · Formula and assumptions shown below

Reaction rate 0.00425 mol/(L·s)
Concentration of A
0.5 mol/L
Set in the form below
Concentration of B
0.25 mol/L
Set in the form below
Rate constant k
0.034 (units vary)
Set in the form below
Order in A
1
Set in the form below
You enter
Concentration of A (mol/L), Concentration of B (mol/L), Rate constant k ((units vary)), Order in A, Order in B
You get
Reaction rate (mol/(L·s))
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The reaction rate formula expresses how fast a chemical reaction proceeds, and its key variables are concentration, temperature, and the rate constant (k), which are related through the rate law equation. To calculate the rate, you need the rate constant, the concentrations of reactants, and the reaction orders for each reactant.

Formula

The general rate law for a reaction aA + bB → products is written as:

rate = k [A]m [B]n

  • rate – the reaction rate, usually in mol/(L·s) or M/s.
  • k – the rate constant, with units that depend on the overall reaction order (e.g., s−1 for first order, L/(mol·s) for second order).
  • [A] and [B] – molar concentrations of reactants A and B, in mol/L.
  • m and n – the reaction orders with respect to A and B, which are determined experimentally, not from the stoichiometric coefficients.

Worked Example

Using the default values from the calculator: [A] = 0.50 mol/L, [B] = 0.25 mol/L, k = 0.034, m = 1, n = 1.

Substitute into the rate law:

rate = 0.034 × (0.50)1 × (0.25)1 = 0.034 × 0.50 × 0.25 = 0.00425 mol/(L·s)

The calculator rounds to 4 decimal places, giving 0.0043 mol/(L·s). This means the reaction consumes A or B at a rate of 0.0043 moles per liter per second under these conditions.

Assumptions

  • The reaction is an elementary step or the rate law is known from experiments.
  • The reaction is isothermal (temperature constant) – k changes with temperature.
  • The concentrations are instantaneous values, not initial concentrations.
  • No reverse reaction is considered (initial rate approximation).
  • Units are consistent: concentrations in mol/L and time in seconds.

How to Determine the Rate Law

You cannot read the orders (m and n) from the balanced equation. They must be found experimentally, typically by the method of initial rates. In this method, you run the reaction several times, changing one reactant’s concentration while keeping others constant, and measure the initial rate. Then you compare how the rate changes with concentration to deduce the order.

For example, if doubling [A] quadruples the rate, then m = 2 (because 22 = 4). If doubling [B] has no effect, then n = 0. The overall reaction order is m + n.

Common Mistakes and Misconceptions

  • Using stoichiometric coefficients as orders: Only for elementary single-step reactions do the coefficients equal the orders; for most reactions, they differ.
  • Forgetting units of k: The units of k depend on the overall order. For a first-order reaction, k has units s−1; for second order, L/(mol·s). Mixing these up leads to wrong rate units.
  • Confusing initial rate with average rate: The rate law uses instantaneous rates, typically the initial rate, not the average over a long time.
  • Ignoring temperature: The rate constant k is highly temperature-dependent, described by the Arrhenius equation. Comparing rates at different temperatures without adjusting k is invalid.

Temperature and the Arrhenius Equation

The rate constant k is not a true constant; it changes with temperature. The Arrhenius equation relates them:

k = A e−Ea/(RT)

  • A – pre-exponential factor (frequency factor), same units as k.
  • Ea – activation energy, in J/mol (or kJ/mol, convert to J).
  • R – gas constant, 8.314 J/(mol·K).
  • T – absolute temperature in Kelvin (K = °C + 273.15).

This shows that even a small temperature increase can dramatically raise the rate because k grows exponentially. For many reactions, the rate roughly doubles for every 10 °C rise, though this rule of thumb varies.

When to Use Which Rate Expression

There are several forms of rate equations, and the choice depends on what you know:

  • Differential rate law: rate = k[A]m[B]n – gives instantaneous rate; used for initial rate studies.
  • Integrated rate laws: relate concentration to time (e.g., ln[A]t = −kt + ln[A]0 for first order). Use these to find k from concentration vs. time data or to predict concentration after a given time.
  • Half-life equations: for first order, t1/2 = 0.693/k; for second order, t1/2 = 1/(k[A]0). Useful for radioactive decay and many reactions.

If you have concentration-time data, plot the data to see which linear form fits (e.g., ln[A] vs. time for first order, 1/[A] vs. time for second order). The slope gives k.

Limitations of the Rate Law

The rate law is empirical and applies only under specific conditions. It assumes the reaction is not affected by factors like pressure (for gases), solvent effects, or the presence of catalysts. Also, the rate law may change if the reaction mechanism changes with concentration (e.g., from first order to second order at high concentrations). For complex reactions with multiple steps, the rate law often reflects the slowest (rate-determining) step, but intermediates and steady-state approximations can complicate things.

Furthermore, the calculator here assumes a simple power-law form. Real systems may have more complex rate expressions, such as Michaelis-Menten kinetics for enzyme-catalyzed reactions or Langmuir-Hinshelwood for surface reactions.

Frequently Asked Questions

What is the difference between reaction order and molecularity?

Reaction order is an experimental quantity determined from the rate law, while molecularity is the number of molecules that collide in an elementary step. For an elementary reaction, they are equal, but for multi-step reactions, the overall order can be fractional or zero, and molecularity is always a small integer (1, 2, or rarely 3).

Can the reaction order be negative or zero?

Yes. A zero order means the rate is independent of that reactant’s concentration (common in enzyme saturation). Negative orders occur when a reactant inhibits the reaction; increasing its concentration slows the rate. The calculator allows orders from 0 to 3, but you can use fractional orders if needed (though the calculator only accepts whole numbers; for fractional orders, use a separate calculation).

How do I find the rate constant k from experimental data?

You can determine k by measuring the rate at known concentrations and solving for k, or by using integrated rate laws and plotting the data. For first order, plot ln[A] vs. time; the slope is −k. For second order, plot 1/[A] vs. time; the slope is k. Alternatively, use the method of initial rates: run several experiments, calculate the rate, and solve for k once orders are known.

Why does the rate constant have different units?

The units of k must make the rate come out in mol/(L·s). For a first-order reaction, rate = k[A], so k has units of s−1. For second order, rate = k[A]2, so k has units of L/(mol·s). For zero order, k has units of mol/(L·s). Always check that your k units match the overall order.

What is the effect of a catalyst on the rate law?

A catalyst provides an alternative pathway with lower activation energy, which increases k but does not change the rate law’s form or the reaction orders. The concentrations of the catalyst may appear in the rate law if it participates in the rate-determining step, but the catalyst itself is not consumed.

How does pressure affect reaction rate for gases?

For gases, increasing pressure increases concentration (since concentration = n/V = P/RT). Thus, the rate law can be written in terms of partial pressures. For example, rate = k PAm PBn. The rate constant k remains the same, but the concentration terms change with pressure.

Related

Formula used
in c | Concentration of A | mol/L | 0.50 | 0 | 10
in d | Concentration of B | mol/L | 0.25 | 0 | 10
in k | Rate constant k | (units vary) | 0.034 | 0 | 1000
in m | Order in A | - | 1 | 0 | 3
in n | Order in B | - | 1 | 0 | 3
out rate | Reaction rate | mol/(L·s) | k * c^m * d^n | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →