molecalculator

Moles & Molar Mass

Resistance Temperature Correction Calculator

Calculator No. 01-4021 · Updated · Formula and assumptions shown below

Resistance at target temperature 123.5800 ohm
Resistance change
23.5800 ohm
= Resistance at target temperature − Resistance at reference temperature
Resistance at reference temperature
100 ohm
Set in the form below
Reference temperature
20 °C
Set in the form below
You enter
Resistance at reference temperature (ohm), Reference temperature (°C), Target temperature (°C), Temperature coefficient of resistance (1/°C)
You get
Resistance at target temperature (ohm), Resistance change (ohm)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A resistance temperature correction calculator estimates a conductor’s resistance at a new temperature from its resistance at a reference temperature and its temperature coefficient. Enter the reference resistance, the two temperatures, and the coefficient; the calculator returns the corrected resistance and its change.

Formula

The calculator uses a linear temperature correction:

R1 = R0[1 + α(T1 − T0)]

  • R1 is the estimated resistance at the target temperature, in ohms (Ω).
  • R0 is the resistance at the reference temperature, in Ω.
  • α is the material’s temperature coefficient of resistance, in inverse degrees Celsius (1/°C), referenced to T0.
  • T1 is the target temperature, in °C.
  • T0 is the reference temperature, in °C.

The temperature difference in Celsius degrees has the same numerical value as the difference in kelvins, so this formula does not require converting temperatures to kelvins. The change is ΔR = R1 − R0. This is a first-order approximation: it assumes α stays constant over the temperature interval.

Worked Example

Using the calculator’s defaults, take a 100 Ω resistance at 20 °C, a target of 80 °C, and α = 0.00393 1/°C. The coefficient is a commonly used approximate value for copper near room temperature; it is not a universal value for every copper sample or operating range.

  1. Find the temperature difference: ΔT = 80 − 20 = 60 °C.
  2. Find the fractional change: αΔT = 0.00393 × 60 = 0.2358.
  3. Calculate target resistance: R1 = 100 × (1 + 0.2358) = 123.58 Ω.
  4. Calculate the change: ΔR = 123.58 − 100 = 23.58 Ω.

The predicted resistance at 80 °C is 123.5800 Ω, an increase of 23.5800 Ω from the reference value.

Assumptions

  • The input coefficient applies to the material and temperature range being considered.
  • Resistance changes approximately linearly with temperature between the reference and target values.
  • The reference resistance and temperatures describe the same component and measurement conditions; self-heating and other changes are not separately modeled.
  • This is a calculation for study and engineering estimates, not a substitute for measurement or a component’s specified data.

How Temperature Correction Works

Electrical resistance depends partly on how a material’s structure affects the movement of charge. In many metals, resistance generally rises as temperature rises. A positive temperature coefficient therefore gives a positive correction when T1 exceeds T0. If the target is cooler, the temperature difference is negative and the estimated resistance falls. Some materials and devices behave differently, especially over broad temperature ranges, so the coefficient and model must match the application.

The coefficient α is a fractional resistance change per degree near a stated reference temperature. For example, 0.00393 1/°C means the simple model predicts a change of about 0.393% of the reference resistance per degree near that reference. It does not mean resistance changes by 0.393 Ω per degree regardless of the starting resistance.

For metals, published coefficients are often approximate and can depend on alloy, purity, manufacturing, and the temperature interval. Use the value supplied for the actual material or component where accuracy matters. Do not treat a typical copper coefficient as suitable for every wire, winding, contact, or temperature.

When to Use the Calculator

Use this calculation when you know a resistance at one temperature and need a first estimate at another—for example, to understand how a wire’s resistance changes as it warms, or to compare a measurement taken under different temperatures. The result is a predicted resistance, not a correction to a measurement instrument’s reading unless the instrument’s measurement setup is otherwise understood.

  • Use the same resistance unit for the reference and reported result; this calculator uses ohms.
  • Enter temperatures in °C, not °F. Convert Fahrenheit first with °C = (°F − 32) × 5/9.
  • Enter α in 1/°C. If a source gives a percentage per degree, divide the percentage number by 100: 0.393%/°C becomes 0.00393 1/°C.
  • Use the reference temperature associated with the stated coefficient. A coefficient defined at a different reference point may not give the same estimate.

The displayed change is signed: a positive value means resistance increased, and a negative value means it decreased. The percentage change can be found from (R1 − R0)/R0 × 100%. In this example, that is 23.58%.

Limits and Common Errors

The linear equation is most useful over a modest interval where the coefficient is effectively constant. Over a wide range, resistance-temperature behavior may be nonlinear. Some reference tables instead give resistance ratios at specified temperatures, or coefficients tied to a particular reference temperature. In those cases, use the material’s table or a more appropriate model rather than extending this equation uncritically.

A frequent mistake is mixing a coefficient expressed as a decimal with one expressed as a percent. Entering 0.393 instead of 0.00393 makes the predicted change 100 times too large. Another is using a coefficient for a different material: a value for pure copper does not automatically describe a copper alloy, a thermistor, or a complete assembled component.

Temperature correction also cannot account for changes caused by mechanical strain, oxidation, contact resistance, aging, or measurement-lead effects. In precision work, measure the component at a known, stable temperature and consult its specification. If the measurement uses leads, a four-wire method can help separate lead resistance from the resistance being measured, where appropriate to the setup.

Frequently Asked Questions

How do I calculate resistance at a different temperature?
Use R1 = R0[1 + α(T1 − T0)]. You need the known resistance, its reference temperature, the target temperature, and a suitable temperature coefficient.

What is the temperature coefficient of copper?
A commonly used approximate value near room temperature is 0.00393 1/°C. The appropriate value can vary with copper condition and temperature range, so use a value tied to the material or specification when available.

Can I use Fahrenheit in the formula?
Not directly with a coefficient stated per °C. Convert both temperatures to Celsius, or use a coefficient expressed per °F. The numerical size of a temperature interval differs between the scales.

Does resistance always increase with temperature?
No. Many metals have a positive coefficient, but other materials and devices can have negative or nonlinear behavior. Check the material’s data rather than assuming the sign or size of α.

Is this formula accurate for any temperature?
No. It is a linear approximation for a range where the coefficient is reasonably constant. For broad ranges or high-accuracy work, use a validated temperature-resistance curve, manufacturer data, or direct measurement.

Why is my measured resistance different from the calculator result?
The entered coefficient may not match the actual material, the component may not be at the assumed temperature, or the measurement may include lead and contact resistance. Self-heating and nonlinear behavior can also matter.

Related

Formula used
in r0 | Resistance at reference temperature | ohm | 100 | 0
in t0 | Reference temperature | °C | 20 | -273.15
in t1 | Target temperature | °C | 80 | -273.15
in alpha | Temperature coefficient of resistance | 1/°C | 0.00393 | 0
out r1 | Resistance at target temperature | ohm | r0 * (1 + alpha * (t1 - t0)) | 4
out dr | Resistance change | ohm | r1 - r0 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →