molecalculator

Moles & Molar Mass

RNA Purity 260/280 Ratio: What the Number Means

Guide 01-3579 · Updated · Step by step

The RNA purity 260/280 ratio is the absorbance at 260 nm divided by the absorbance at 280 nm; purified RNA commonly has a ratio near 2.0, often described as roughly 1.9–2.1. It is a quick indicator of possible protein or other UV-absorbing contamination, not a complete measure of RNA quality or proof that a sample is suitable for every experiment.

What the 260/280 ratio measures

Nucleic acids absorb ultraviolet light strongly around 260 nm. Proteins, especially those containing aromatic amino acids such as tryptophan and tyrosine, absorb more strongly around 280 nm. A spectrophotometer therefore compares the sample’s absorbance at these two wavelengths: A260 divided by A280. A relatively high value is expected for RNA because its absorbance at 260 nm is substantial.

For example, if a correctly blanked sample has A260 = 0.40 and A280 = 0.20, its ratio is 0.40 / 0.20 = 2.0. The ratio has no units. It does not report RNA concentration by itself; concentration is estimated separately, commonly from A260 and the instrument’s chosen conversion factor and dilution settings.

The familiar value near 2.0 is a practical reference rather than a universal pass/fail boundary. RNA composition, pH, ionic strength, instrument type, measurement range, and sample contaminants can all influence the reading. Interpret it alongside the sample’s intended use and other quality checks.

How to interpret a result

A ratio near 2.0 is generally consistent with relatively pure RNA in a UV absorbance measurement. A lower ratio can point to protein, phenol, or other substances that increase absorbance near 280 nm, but it cannot identify a contaminant on its own. A higher result may arise from measurement conditions, blanking errors, low absorbance, or contaminants with different spectral properties; it is not evidence that the RNA is exceptionally pure.

  • About 1.9–2.1: commonly considered close to the expected range for RNA, but still check concentration and integrity.
  • Below about 1.8: investigate possible protein or extraction-reagent carryover and review the blank and sample preparation.
  • Above about 2.1: check whether the sample is dilute, whether the blank matches the sample buffer, and whether the reading is reproducible.

These ranges are guidelines, not universal acceptance criteria. A downstream assay’s requirements may be stricter or more permissive. If the ratio is unusual, repeat the measurement after confirming the instrument is blanked with the appropriate solution and that the sample is mixed and measured as intended.

Why the ratio can be misleading

A ratio is a quotient, so it can look extreme when the denominator is very small. If A280 is close to the instrument’s detection limit, small amounts of noise can change A260/A280 substantially. This is especially important for dilute samples: a displayed ratio with several decimal places may imply more certainty than the measurement supports.

Blanking matters because the blank should match the solution in which the RNA is suspended, as far as the method allows. A mismatch in buffer, pH, or other dissolved substances can alter the baseline. Bubbles, droplets, fingerprints, residue on a measurement surface, or inconsistent sample handling can also cause unreliable readings. Follow the instrument’s instructions and the validated method used in the lab.

The 260/280 ratio also does not reveal whether RNA is intact. Degraded RNA can still produce a ratio near 2.0. Nor does it reliably detect every contaminant: salts and some extraction chemicals may affect other wavelengths or interfere with downstream reactions without producing an obvious 260/280 warning.

260/280 compared with 260/230

The 260/230 ratio is a separate absorbance check, calculated as A260 divided by A230. Clean nucleic-acid samples often show a value around 2.0–2.2, though the appropriate interpretation depends on measurement conditions. Absorbance near 230 nm can be affected by substances such as salts, carbohydrates, phenol, and some organic compounds used in extraction or cleanup.

Reading both ratios can help narrow down a concern, but neither ratio identifies a compound definitively. For instance, an acceptable 260/280 with a low 260/230 may suggest a problem that the 260/280 measurement does not show. Conversely, acceptable ratios do not guarantee that a sample will perform well in reverse transcription, amplification, sequencing, or another application.

What to check when the ratio is off

Before concluding that RNA needs additional cleanup, verify that the measurement itself is trustworthy. A practical check sequence is:

  1. Confirm the blank is appropriate for the sample’s solution and that the instrument is clean and set up correctly.
  2. Check whether the absorbance values are within the instrument’s reliable measurement range; be cautious when either value is very low.
  3. Repeat the reading using a fresh aliquot and consistent handling, avoiding bubbles and surface residue.
  4. Review the extraction and sample records for possible carryover, then use an appropriate validated cleanup or assessment method if the result remains concerning.
  5. Assess concentration and RNA integrity separately, using methods suited to the intended application.

Do not apply a cleanup step automatically just to force a ratio into a preferred range. Cleanup can reduce the amount of recovered RNA, and a ratio shift may instead reflect blanking, low concentration, or measurement noise. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Other measures of RNA quality

Concentration and purity answer different questions. UV absorbance can estimate concentration, while fluorometric methods can provide a more selective RNA concentration measurement in some settings. Neither concentration result tells you whether RNA is intact.

Integrity is assessed with methods that examine the RNA’s size distribution or degradation pattern, such as electrophoretic analysis. The appropriate test and acceptance threshold depend on the application: short targeted assays may tolerate degradation that would be unsuitable for methods requiring intact, full-length RNA. Functional performance in the intended workflow is ultimately important, so follow that workflow’s quality criteria rather than relying on one ratio alone.

Frequently Asked Questions

What is a good 260/280 ratio for RNA?
A value close to 2.0 is commonly expected; roughly 1.9–2.1 is often used as a practical reference range. It is not a universal cutoff, so consider concentration, measurement conditions, and the requirements of the intended application.

Does a 260/280 ratio of 1.8 mean my RNA is contaminated?
Not necessarily. It may reflect protein or another UV-absorbing contaminant, but low absorbance, a mismatched blank, buffer conditions, or measurement variability can also affect the result. Repeat and review the measurement before deciding what it means.

Can RNA have a good 260/280 ratio but still be degraded?
Yes. The ratio reflects absorbance at two wavelengths, not the length or integrity of RNA molecules. Use an integrity assessment appropriate for the planned experiment.

What does a high RNA 260/280 ratio mean?
A high value does not automatically mean unusually pure RNA. It can result from a small or noisy A280 reading, low sample concentration, blanking problems, or other measurement conditions. Check the underlying absorbance values and repeat if needed.

Is 260/280 enough to judge RNA purity?
No. It is one screening measure. The 260/230 ratio can provide complementary information, and concentration, integrity, and performance in the intended application should be considered separately.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →