molecalculator

Moles & Molar Mass

Room Pressure Calculation Formula

Calculator No. 01-11954 · Updated · Formula and assumptions shown below

Pressure difference 68.49 Pa
Pressure difference
0.275 in w.c.
= Pressure difference ÷ 249.089
Airflow rate
250 m³/h
Set in the form below
Effective opening area
100 cm²
Set in the form below
You enter
Airflow rate (m³/h), Effective opening area (cm²), Discharge coefficient
You get
Pressure difference (Pa), Pressure difference (in w.c.)
Rounding
2 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Room pressure calculation is the process of determining the pressure difference between a room and its surroundings, typically using the formula ΔP = Q × (1 / (K × A))², where ΔP is the pressure difference, Q is the airflow rate, K is a flow coefficient, and A is the effective opening area. In practice, you enter the airflow (in CFM or m³/h), the opening area (door undercut, gap, or vent), and a discharge coefficient to get the pressure differential in Pascals or inches of water column.

Formula

The basic orifice equation relates pressure difference to airflow through an opening:

ΔP = (Q / (K × A))² × ρ / 2

Where:

  • ΔP = pressure difference (Pascals, Pa)
  • Q = volumetric airflow rate (m³/s)
  • K = discharge coefficient (dimensionless, typically 0.6–0.7 for sharp-edged openings)
  • A = effective open area (m²)
  • ρ = air density (kg/m³, about 1.2 at 20°C and 1 atm)

In the calculator above, you input Q in m³/h and A in cm²; the expression converts them to SI units (divide Q by 3600, divide A by 10000). The first output is the pressure difference in Pascals, and the second converts to inches of water column (1 in w.c. = 249.089 Pa).

Worked Example

Using the defaults: Q = 250 m³/h, A = 100 cm², K = 0.65.

  1. Convert airflow: Q = 250 / 3600 = 0.06944 m³/s
  2. Convert area: A = 100 / 10000 = 0.01 m²
  3. Compute velocity through opening: v = Q / (K × A) = 0.06944 / (0.65 × 0.01) = 10.683 m/s
  4. Dynamic pressure: ΔP = 0.5 × ρ × v² = 0.5 × 1.2 × (10.683)² = 0.6 × 114.13 = 68.48 Pa
  5. Convert to in w.c.: 68.48 / 249.089 = 0.275 in w.c.

The calculator shows 68.48 Pa and 0.275 in w.c. (rounded to 2 and 3 decimals respectively).

Assumptions

  • Air is incompressible (valid for low pressure differences, typically < 1000 Pa)
  • Steady, turbulent flow through a sharp-edged orifice
  • Air density is constant at 1.2 kg/m³ (20°C, sea level)
  • The opening is the only path for air; no other leaks or supply/exhaust imbalances
  • The discharge coefficient K accounts for vena contracta and friction losses

When to Use This Formula

This formula is used in HVAC design, cleanroom engineering, and building pressurization studies. You apply it when you need to estimate the pressure difference that a given airflow will create across a door, window, or intentional vent. For example, a hospital isolation room might need a pressure differential of -2.5 Pa relative to the corridor; you would use this formula to size the exhaust airflow required to achieve that.

It is also used to check existing rooms: measure the airflow through a door undercut (using a flow hood) and calculate whether the pressure difference meets code. Conversely, if you know the target pressure difference and the opening area, you can rearrange the formula to find the required airflow.

How to Choose the Discharge Coefficient (K)

The discharge coefficient is not a fixed constant; it depends on the geometry of the opening:

  • Sharp-edged orifice (thin door undercut): K ≈ 0.60–0.65
  • Rounded entrance (bell-mouth vent): K ≈ 0.90–0.98
  • Short pipe or duct: K ≈ 0.80–0.90
  • Long rectangular slot (door gap): K ≈ 0.60–0.70

If you have no data, 0.65 is a reasonable default for a typical door undercut. For a more accurate value, consult ASHRAE or local engineering guidelines. The formula is sensitive to K: a 10% change in K changes ΔP by about 20% (since K is squared in the denominator).

Common Mistakes and Misconceptions

  • Unit mix-ups: Forgetting to convert m³/h to m³/s (divide by 3600) is the most common error. Similarly, using cm² instead of m² (divide by 10,000) leads to a factor of 10⁴ error.
  • Using the wrong density: Air density varies with temperature and altitude. At 40°C, ρ ≈ 1.13 kg/m³; at 3000 m altitude, ρ ≈ 0.9 kg/m³. For precise work, calculate ρ = P/(R×T) with P in Pa, R=287 J/(kg·K), T in Kelvin.
  • Ignoring multiple openings: If a room has several gaps (door, window, vent), the total effective area is not the sum; it’s the parallel combination: A_total = A₁ + A₂ + … only if they are in parallel with the same pressure drop. In reality, you need the series-parallel network, which is more complex.
  • Assuming the formula gives the room pressure directly: The formula gives the pressure difference across a single opening for a given flow. To find the room pressure relative to outside, you must consider all openings and the supply/exhaust balance.
  • Confusing static and dynamic pressure: The formula gives the dynamic pressure (velocity pressure) of the air through the opening. In a room, the static pressure is what you measure with a manometer; they are related but not identical unless the room is perfectly sealed.

Limitations of the Formula

This orifice equation is a simplification. It assumes steady, incompressible flow and a single sharp-edged opening. In real rooms, air paths are often complex: doors have frames, gaps are irregular, and there may be multiple leaks. The formula also ignores friction losses in long ducts and the effect of air temperature stratification. For very low pressure differences (less than 1 Pa), buoyancy and wind can dominate, making the formula unreliable.

For building pressurization, the standard method is the blower door test, which uses a calibrated fan and multiple pressure readings to fit a power law (Q = C × ΔPⁿ, where n is typically 0.6–0.7). The orifice formula is a special case with n=0.5. For design purposes, use the orifice formula for quick estimates, but verify with actual measurements.

Alternatives and Related Methods

If you need more accuracy, consider:

  • ASHRAE Fundamentals: Provides detailed leakage data for different construction types and equations for multi-zone networks.
  • CFD simulation: Computational fluid dynamics can model complex room geometries, but requires specialist software and training.
  • Empirical leakage curves: Many building codes provide tables of leakage per area for walls, windows, and doors, which you can use with the power law.
  • Blower door measurement: The most accurate way to determine a room’s leakage and pressure response; use it to calibrate your model.

For cleanrooms, the relevant standard is ISO 14644, which specifies pressure differentials and airflow rates; the formula here helps you size the system.

Frequently Asked Questions

What is the normal room pressure?

There is no single

Related

Formula used
in q | Airflow rate | m³/h | 250 | 0 | 5000
in a | Effective opening area | cm² | 100 | 1 | 10000
in k | Discharge coefficient | - | 0.65 | 0.1 | 1
out dp | Pressure difference | Pa | (q / 3600 / (k * a / 10000))^2 * 1.2 / 2 | 2
out dpi | Pressure difference | in w.c. | dp / 249.089 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →