molecalculator

Moles & Molar Mass

Sodium Hydroxide vs Potassium Hydroxide Calculator

Calculator No. 01-1191 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator compares the amount of sodium hydroxide (NaOH) or potassium hydroxide (KOH) needed to supply the same number of hydroxide moles, based on the mass of either pure, anhydrous reagent. Enter the mass of one hydroxide and select which one it is; the calculator returns the equivalent mass of the other and the hydroxide amount in moles.

Formula

Both compounds provide one mole of hydroxide ions per mole of pure compound under the complete-dissociation assumption. First calculate the amount, n = m / M, where m is reagent mass in grams and M is molar mass in grams per mole. Then calculate the equivalent mass of the other compound as mother = n × Mother. The calculator uses M(NaOH) = 39.997 g/mol and M(KOH) = 56.1056 g/mol, based on standard atomic weights: Na 22.990, K 39.0983, O 15.999 and H 1.008.

The selector value is 1 for sodium hydroxide and 2 for potassium hydroxide. The first result is the mass of the alternative base that supplies the same nominal amount of hydroxide; the second is that amount in moles. For example, the equivalent-mass expression selects 56.1056/39.997 when the input is NaOH and 39.997/56.1056 when it is KOH.

Worked Example

Using the defaults—10 g of sodium hydroxide—the amount is:

n = 10 g / 39.997 g/mol = 0.2500188 mol ≈ 0.2500 mol.

The equivalent potassium hydroxide mass is:

m(KOH) = 0.2500188 mol × 56.1056 g/mol = 14.028 g ≈ 14.0280 g.

The calculator displays 14.0280 g and 0.2500 mol at four decimal places. The final-digit difference that can arise from rounding the intermediate amount does not change the calculated result.

Assumptions

  • The reagent is pure, anhydrous NaOH or KOH, and its stated mass is the mass of the hydroxide itself.
  • Each formula unit supplies one hydroxide ion, and complete dissociation is assumed for the mole comparison.
  • This is a stoichiometric comparison, not a prediction of pH, reaction rate, or practical performance.

What the Comparison Means

Sodium hydroxide and potassium hydroxide are strong, caustic bases. In water, each dissociates extensively into metal ions and hydroxide ions. Their molar masses differ, so equal masses do not contain equal numbers of hydroxide moles. A gram of NaOH represents more moles than a gram of KOH; conversely, more KOH by mass is needed to match a given mass of pure NaOH.

The calculator compares chemical amounts, not equal volumes or equal measured pH. If each compound is dissolved and brought to the same final volume, matching hydroxide moles gives the same nominal concentration under idealized conditions. Actual pH can also depend on temperature, concentration, activity effects, carbon dioxide uptake, other ingredients, and measurement conditions.

How to Choose Between Them

The right choice depends on the application and its established formulation or method, not simply on which base is “stronger.” Both are strong bases; the key practical differences include the metal ion left in the mixture, physical handling, solubility, and how the product is intended to be used. Do not substitute one for the other by equal mass.

  • Use NaOH when: a validated method or product specification calls for sodium hydroxide, or sodium ions are the required counterions.
  • Use KOH when: the method specifies potassium hydroxide, or potassium ions are appropriate for the intended chemistry.
  • When replacing one with the other: compare moles, then check whether the accompanying sodium or potassium ions affect the reaction, final product, or downstream analysis.

In soapmaking, for instance, the choice of alkali is part of the formulation: NaOH is commonly associated with hard bar soaps and KOH with softer or liquid soaps. This is a useful example of why mole-equivalent replacement does not guarantee an identical product. Follow a formulation designed for the specific hydroxide rather than treating the calculator as a complete recipe.

Purity, Moisture, and Common Errors

The calculation is only as reliable as the mass and purity assumptions. Solid NaOH and KOH absorb moisture from air; they can also absorb carbon dioxide, forming carbonate-containing material. Consequently, an old or exposed sample may not contain the nominal amount of active hydroxide implied by its gross mass. Commercial solutions and products may have a stated concentration or purity that differs from 100%.

  • Do not enter the mass of a solution as though it were the mass of pure solid. Use the active hydroxide mass, based on a reliable concentration or assay.
  • Check the product specification and method for purity, hydration, or concentration. The simple calculator does not correct for these.
  • Keep units consistent: the input is grams, and the molar masses are in grams per mole.
  • Do not interpret equivalent mass as an equal-volume instruction. A solution’s final volume must be considered separately.

Safety and Scope

Both substances can cause severe skin and eye burns. Dissolving solid hydroxide releases heat, and splashes are a serious hazard. Use the protective equipment, facilities, handling instructions, and first-aid guidance specified by the applicable safety data sheet (SDS) and workplace rules. Do not rely on this calculator as a preparation procedure. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Keep caustic materials away from children and food areas, and never handle them without suitable training and protective measures. If exposure occurs, follow the SDS and local emergency procedures immediately. This page is for general chemistry and lab-planning arithmetic, not for medical, food, or household-use instructions.

Frequently Asked Questions

Which is stronger, sodium hydroxide or potassium hydroxide?
Both are strong bases in water and dissociate extensively. “Stronger” is not a useful way to distinguish them for ordinary stoichiometric calculations; their molar masses and metal ions differ.

Can I replace NaOH with KOH gram for gram?
No. Their molar masses are different. Use the mole-equivalence calculation, and confirm that changing sodium ions to potassium ions is acceptable for the application.

How much KOH equals 10 g of NaOH?
For pure, anhydrous reagents, 10 g NaOH corresponds to about 14.028 g KOH, supplying the same nominal hydroxide amount.

Does equal hydroxide amount mean equal pH?
Not necessarily. Equal amounts produce equal nominal hydroxide concentration only when final volumes and relevant conditions are also comparable. Real pH depends on concentration, temperature, ionic strength, and other components.

Does the calculator account for reagent purity?
No. It assumes pure, anhydrous material. If the reagent is a solution or has a known assay, calculate its active hydroxide content first using that product information.

Related

Formula used
in m | Reagent mass | g | 10 | 0
sel b | Starting hydroxide | Sodium hydroxide=1, Potassium hydroxide=2
out e | Equivalent mass of the other hydroxide | g | m * (b = 1) * 56.1056 / 39.997 + m * (b = 2) * 39.997 / 56.1056 | 4
out n | Amount of hydroxide | mol | m / (b = 1) * 39.997 + m / (b = 2) * 56.1056 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →