molecalculator

Moles & Molar Mass

Standard Reaction Free Energy Calculator

Calculator No. 01-10610 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator determines the standard Gibbs free energy change (ΔG°) for a chemical reaction using the relationship ΔG° = –RT ln K. You enter the equilibrium constant (K) and the temperature, and the calculator returns the standard reaction free energy in kJ/mol, along with a helpful interpretation of whether the reaction is spontaneous under standard conditions.

Formula

The standard Gibbs free energy change is calculated from the equilibrium constant using:

ΔG° = –RT ln K

  • ΔG° – standard Gibbs free energy change (kJ/mol)
  • R – universal gas constant, 8.31446261815324 J/(mol·K)
  • T – absolute temperature (K) = temperature in °C + 273.15
  • K – equilibrium constant (dimensionless; use the thermodynamic equilibrium constant)

Note that the calculator converts the result to kJ/mol by dividing by 1000. The spontaneity output is a binary flag: 1 means ΔG° is negative (spontaneous under standard conditions), 0 means ΔG° is positive (non-spontaneous under standard conditions).

Worked Example

Using the default values: K = 1.5 × 10–3 and T = 25 °C.

  1. Convert temperature to kelvin: T = 25 + 273.15 = 298.15 K
  2. Calculate RT: 8.31446261815324 × 298.15 = 2479.0 J/mol (approximately)
  3. Divide by 1000 to get kJ/mol: 2.479 kJ/mol
  4. Compute ln(K): ln(1.5 × 10–3) = –6.5023
  5. Multiply: ΔG° = –(2.479) × (–6.5023) = +16.12 kJ/mol

The calculator shows ΔG° = 16.12 kJ/mol, which is positive, so the reaction is non-spontaneous under standard conditions at 25 °C. The spontaneity flag shows 0.

Assumptions

  • The reaction is at equilibrium, and K is the thermodynamic equilibrium constant (activities, not concentrations).
  • The temperature is constant and uniform.
  • Ideal gas behavior or ideal solution behavior is assumed for the species involved.
  • Standard states are defined as 1 bar (or 1 atm) for gases, 1 M for solutions, and pure solids/liquids.

When to Use This Calculator

You use this calculator when you have an equilibrium constant measured at a known temperature and want to know the standard free energy change. This is common in:

  • Comparing the spontaneity of reactions at standard conditions
  • Estimating the position of equilibrium (a more negative ΔG° means a larger K)
  • Converting between ΔG° and K in thermodynamics problems
  • Checking whether a reaction is product-favored or reactant-favored

Remember that ΔG° refers to standard conditions (all reactants and products at 1 M, 1 bar, etc.). The actual free energy change under non-standard conditions is given by ΔG = ΔG° + RT ln Q, where Q is the reaction quotient.

How to Read the Result

The sign of ΔG° tells you about spontaneity under standard conditions:

  • ΔG° < 0: reaction is spontaneous forward (products favored at equilibrium).
  • ΔG° = 0: reaction is at equilibrium; K = 1.
  • ΔG° > 0: reaction is non-spontaneous forward (reactants favored); the reverse reaction is spontaneous.

The magnitude matters too. A ΔG° of –20 kJ/mol corresponds to a large K (about 3 × 103 at 25 °C), while –5 kJ/mol gives K ≈ 7.5. Small changes in ΔG° translate into large changes in K because of the exponential relationship.

Common Mistakes and Misconceptions

  • Using concentration-based K instead of thermodynamic K: For solutions, use activities (approximately molarity for dilute solutions). For gases, use partial pressures in bar. If you use Kc (concentrations) when gases are involved, you must account for units.
  • Forgetting to convert temperature to kelvin: The formula requires absolute temperature. Using Celsius directly gives a wrong answer.
  • Mixing up R units: R = 8.314 J/(mol·K). If you use R in kJ, be consistent. Our calculator handles the conversion.
  • Assuming ΔG° tells you about rate: Thermodynamics says nothing about how fast a reaction proceeds. A reaction can have a negative ΔG° but be extremely slow without a catalyst.
  • Thinking ΔG° is constant with temperature: ΔG° changes with temperature because ΔH° and ΔS° are temperature-dependent (though often assumed constant over small ranges). If you need ΔG° at a different temperature, you must use the van’t Hoff equation or calculate from ΔH° and ΔS°.

Limits of the Formula

The equation ΔG° = –RT ln K is exact for any reaction at equilibrium, but its practical use depends on the quality of K. For reactions with very large or very small K values, numerical precision can be an issue. For example, if K is 1010, ln K is about 23, and ΔG° is about –57 kJ/mol at 25 °C. If K is 10–10, ΔG° is +57 kJ/mol. The calculator handles a wide range, but keep in mind that K values are often measured with limited precision, and the resulting ΔG° carries that uncertainty.

Also, the standard free energy change is a composite of enthalpy and entropy: ΔG° = ΔH° – TΔS°. If you need to separate these contributions, you must measure K at multiple temperatures and use the van’t Hoff equation.

Frequently Asked Questions

What is the difference between ΔG and ΔG°?

ΔG° is the free energy change when all reactants and products are in their standard states (1 bar, 1 M, etc.). ΔG is the actual free energy change under any set of concentrations or pressures. They are related by ΔG = ΔG° + RT ln Q, where Q is the reaction quotient. At equilibrium, ΔG = 0 and Q = K, so ΔG° = –RT ln K.

Can I use this calculator for reactions in solution?

Yes, as long as you use the thermodynamic equilibrium constant based on activities. For dilute solutions, activities are approximately equal to molar concentrations, so using Kc is usually fine. For non-ideal solutions, you would need activity coefficients, which are beyond the scope of this simple calculator.

What if my K is very large or very small?

The calculator accepts K values from 1e-30 to 1e30 (you can enter scientific notation like 1e10). For extremely large or small K, the calculated ΔG° will be correspondingly large in magnitude, but the sign still tells you about spontaneity. Be aware that such extreme values are often not measured directly but derived from other thermodynamic data.

Does temperature affect ΔG°?

Yes, ΔG° depends on temperature because both ΔH° and ΔS° have temperature dependencies. The equation ΔG° = –RT ln K shows that even if K were constant, ΔG° would change with T. In reality, K also changes with temperature. To find ΔG° at a different temperature, you need K at that temperature or use ΔH° and ΔS° values.

Why do I get a positive ΔG° for a reaction that happens spontaneously?

A positive ΔG° means the reaction is non-spontaneous under standard conditions. But in practice, reactions are often run under non-standard conditions. For example, if you have a high concentration of reactants, Q < K, and ΔG becomes negative even if ΔG° is positive. Also, some reactions are driven by coupling to other reactions or by removing products continuously.

How do I find K from ΔG°?

Rearrange the equation: K = exp(–ΔG° / (RT)). Make sure ΔG° is in J/mol and T is in kelvin. For example, if ΔG° = –10 kJ/mol at 25 °C, then K = exp(10000 / (8.314 × 298.15)) ≈ exp(4.04) ≈ 57. This is a common calculation in biochemistry and chemistry courses.

Related

Formula used
in k | Equilibrium constant K | - | 1.5e-3 | 1e-30
in t | Temperature | °C | 25 | -273.15
out dg | Standard free energy change ΔG° | kJ/mol | -8.31446261815324 * (t + 273.15) / 1000 * ln(k) | 2
out spont | Spontaneity at standard conditions | - | (dg < 0) * 1 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →