molecalculator

Moles & Molar Mass

Thermal Conductivity Conversion Calculator

Calculator No. 01-10362 · Updated · Formula and assumptions shown below

Converted value 1.000000
Value to convert
1
Set in the form below
From unit
W/(m·K)
Set in the form below
To unit
W/(m·K)
Set in the form below
You enter
Value to convert, From unit, To unit
You get
Converted value
Rounding
6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A thermal conductivity conversion calculator converts a value expressed in one unit of thermal conductivity (such as W/(m·K), W/(cm·°C), BTU/(ft·h·°F), or cal/(cm·s·°C)) into another unit. You enter the numeric value and select the current and target units, and the calculator returns the equivalent value in the new unit.

Formula

Thermal conductivity k measures how well a material conducts heat. It is defined by Fourier’s law: heat flux (W/m²) equals k times the temperature gradient (K/m). The SI unit is watts per meter-kelvin, W/(m·K).

To convert between units, multiply the original value by the ratio of the base unit (W/(m·K)) equivalents:

  • 1 W/(cm·°C) = 100 W/(m·K) (because 1 cm = 0.01 m and a 1 °C difference equals 1 K)
  • 1 BTU/(ft·h·°F) = 1.730735 W/(m·K)
  • 1 cal/(cm·s·°C) = 418.68 W/(m·K) (using 1 cal = 4.1868 J)

So the conversion is: value in target unit = value in original unit × (W/(m·K) equivalent of original unit) / (W/(m·K) equivalent of target unit).

Worked Example

Convert 1 BTU/(ft·h·°F) to W/(m·K). Using the defaults from the calculator:

  1. Original value = 1, from unit = BTU/(ft·h·°F) (factor = 1.730735), to unit = W/(m·K) (factor = 1).
  2. Result = 1 × 1.730735 / 1 = 1.730735 W/(m·K).

The calculator shows 1.730735 (rounded to 6 decimals). This matches the standard conversion factor.

Assumptions

  • The conversion uses the international calorie (1 cal = 4.1868 J), which is the common thermochemical calorie. Some older tables use the 15 °C calorie (4.1855 J), which differs by ~0.03%.
  • Temperature differences in °C and K are treated as identical because a change of 1 °C equals a change of 1 K.
  • The BTU factor is based on the International Table BTU (1 BTU = 1055.056 J).

Why Convert Thermal Conductivity?

Engineers and scientists often need to compare materials listed in different unit systems. For example, a European datasheet might give a polymer’s thermal conductivity in W/(m·K), while an American textbook uses BTU/(ft·h·°F). Converting ensures you are comparing the same property. Also, many thermal simulation software packages require input in a specific unit; a wrong conversion can lead to design errors.

Common Mistakes

  • Confusing W/(m·K) with W/(cm·°C): the latter is 100 times larger. A value of 0.5 W/(cm·°C) is 50 W/(m·K), not 0.5.
  • Using the wrong calorie definition. The difference is small but can matter in high-precision work.
  • Forgetting that BTU/(ft·h·°F) is per hour, not per second. The conversion factor already includes the hour, so do not multiply by 3600 again.
  • Mixing up thermal conductivity (W/(m·K)) with thermal conductance (W/(m²·K)) or thermal resistance (m²·K/W). Those are different quantities.

How to Choose the Right Unit

Use the unit that matches your source data or your application. In scientific research and SI-based engineering, W/(m·K) is standard. In US construction and HVAC, BTU/(ft·h·°F) appears in older references. W/(cm·°C) is common in older physics and chemistry tables. Cal/(cm·s·°C) is rare but appears in some older chemistry texts. Always state the unit when reporting thermal conductivity; a bare number is meaningless.

Limits of the Conversion

This calculator only converts units; it does not account for temperature dependence. Thermal conductivity of many materials changes with temperature. For example, metals typically decrease in conductivity as temperature rises, while insulators may increase slightly. The conversion is exact for the units, but the underlying value may be valid only at the temperature specified in the source. Also, anisotropic materials (like wood or composites) have different conductivities in different directions; the unit conversion does not address that.

Frequently Asked Questions

What is the difference between W/(m·K) and W/(m·°C)?

There is no numerical difference because a temperature interval of 1 kelvin equals an interval of 1 degree Celsius. The two units are used interchangeably; only the scale zero differs, which cancels when measuring differences.

How do I convert BTU/(ft·h·°F) to W/(m·K) without a calculator?

Multiply the BTU value by 1.730735. For example, 10 BTU/(ft·h·°F) ≈ 17.31 W/(m·K).

Why does my textbook list thermal conductivity in cal/(cm·s·°C)?

Older scientific literature, especially in chemistry and physics, used cgs units. The conversion to SI is 1 cal/(cm·s·°C) = 418.68 W/(m·K).

Is thermal conductivity the same as thermal diffusivity?

No. Thermal diffusivity (m²/s) equals thermal conductivity divided by density times specific heat capacity. It measures how quickly heat spreads through a material, not just how well it conducts.

What is a typical value for common materials?

Copper is about 401 W/(m·K), aluminum about 205 W/(m·K), steel about 50 W/(m·K), water about 0.6 W/(m·K), and air about 0.026 W/(m·K). These are at room temperature.

Always verify the original unit and temperature when using a conversion. For lab work, follow your method, the safety data sheet (SDS), and your supervisor.

Related

Formula used
in val | Value to convert | - | 1 | 0
sel from | From unit | W/(m·K)=1, W/(cm·°C)=2, BTU/(ft·h·°F)=3, cal/(cm·s·°C)=4
sel to | To unit | W/(m·K)=1, W/(cm·°C)=2, BTU/(ft·h·°F)=3, cal/(cm·s·°C)=4
out result | Converted value | - | val * from / to | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →