This page provides a table of thermal conductivity values for common gases at standard conditions (usually 25 °C and 1 atm), explains what the numbers mean, and shows how to use them in calculations. Enter a gas’s conductivity (W/m·K) or use the defaults to compute heat flux through a gas layer.
Formula
The heat flux through a flat layer of gas is given by Fourier’s law for one-dimensional steady-state conduction:
q = k × ΔT / d
- q = heat flux (W/m²)
- k = thermal conductivity of the gas (W/m·K)
- ΔT = temperature difference across the layer (K or °C, since it’s a difference)
- d = thickness of the gas layer (m)
This formula assumes steady-state conditions, no convection or radiation, and a homogeneous gas. For most engineering estimates, it works well for thin gas gaps where natural convection is suppressed (e.g., double-pane windows, foam gas pockets).
Worked Example
Using the default values from the calculator: k = 0.026 W/m·K (approximate conductivity of air at 25 °C), ΔT = 50 K, and d = 0.01 m.
Plug into the formula:
q = (0.026 W/m·K) × (50 K) / (0.01 m)
q = 1.3 W/m·K × 50 K / 0.01 m = 130 W/m²
The calculator returns 130.0 W/m², matching the manual calculation.
Assumptions
- Steady-state conduction (no time dependence).
- Gas is homogeneous and isotropic.
- No convection or radiation heat transfer.
- Thermal conductivity is constant over the temperature range (acceptable for small ΔT).
- Pressure is near atmospheric; conductivity of gases is nearly independent of pressure except at very low vacuum or very high pressure.
Thermal Conductivity of Common Gases at 25 °C and 1 atm
Values are approximate and vary slightly with temperature and source (CRC Handbook, NIST, etc.). Units are W/m·K.
- Air: 0.026
- Argon (Ar): 0.0177
- Carbon dioxide (CO₂): 0.0166
- Helium (He): 0.151
- Hydrogen (H₂): 0.182
- Methane (CH₄): 0.034
- Nitrogen (N₂): 0.026
- Oxygen (O₂): 0.026
- Water vapor (steam at 100 °C): 0.025
Notice that light gases (helium, hydrogen) have much higher conductivity than heavier gases. This is because thermal conductivity in gases is related to molecular speed and mean free path—lighter molecules move faster and transfer energy more efficiently.
How Gas Thermal Conductivity Works
In a gas, heat is conducted by molecular collisions. Molecules in the hotter region have higher kinetic energy; they collide with cooler molecules and transfer energy. The efficiency of this transfer depends on:
- Molecular speed: lighter molecules move faster, increasing collision frequency.
- Mean free path: longer paths allow molecules to carry energy further between collisions.
- Specific heat capacity: gases with more internal modes (rotation, vibration) can store more energy per molecule, but this also affects how energy is transferred.
Unlike solids, gas conductivity is almost independent of pressure over a wide range (from a few kPa to hundreds of kPa). Only at very low pressures (vacuum) or very high pressures (near critical point) does it change significantly.
How to Use the Table and Calculator
Pick the gas that matches your situation from the table above, or look up a more precise value for your temperature. Enter that value into the calculator along with the temperature difference and the thickness of the gas layer. The result is the heat flux per square meter—how much heat flows through each square meter of the gas layer per second.
For example, to estimate heat loss through an argon-filled double-pane window with a 1 cm gap and 20 °C indoor/outdoor difference, use k = 0.0177, ΔT = 20, d = 0.01. The calculator gives 35.4 W/m². For air it would be 52 W/m², showing why argon is used in high-efficiency windows.
Common Mistakes and Misconceptions
- Using °C instead of K in ΔT: Since it’s a difference, 1 °C = 1 K, so it’s fine. But don’t add 273.15 to ΔT.
- Confusing thermal conductivity with thermal resistance: Resistance = thickness / (conductivity × area). The calculator gives flux, not total heat.
- Ignoring convection: In thick gas layers (more than a few cm), natural convection dominates. The formula only works for thin gaps or still gas.
- Assuming conductivity is constant: It increases with temperature roughly as T^0.5 to T^1.0. For wide temperature ranges, use a temperature-dependent value.
Why Gas Conductivity Matters in Real Life
Gas thermal conductivity is critical in many applications:
- Insulation: Foam insulation uses trapped gas (often air or a blowing agent) in cells. Lower conductivity gas means better insulation.
- Double-glazed windows: Argon or krypton fills reduce heat loss compared to air.
- Electronics cooling: Helium is used in some high-end cooling systems because it conducts heat well and is inert.
- Gas sensors: Some sensors measure thermal conductivity to detect gas composition (e.g., hydrogen leaks).
- Heat exchangers: When gas is the working fluid, its conductivity affects heat transfer rates.
Safety and Practical Notes
When working with gases in a lab, always follow your lab method, the safety data sheet (SDS) and your supervisor. Some gases (hydrogen, methane) are flammable; helium can displace oxygen in confined spaces. Thermal conductivity measurements are non-hazardous, but the gas itself may pose risks. Never use this calculator for medical or clinical purposes—it’s for engineering and educational use only.
Frequently Asked Questions
Why is helium’s thermal conductivity so high?
Helium atoms are very light and small, so they move at high speeds and have long mean free paths. This allows them to transfer kinetic energy more efficiently between collisions, resulting in a conductivity about six times that of air.
Does pressure affect gas thermal conductivity?
At moderate pressures (roughly 0.01 atm to 10 atm), conductivity is nearly constant because the increase in collision frequency is offset by a decrease in mean free path. Only at very low pressures (vacuum) does conductivity drop, and at very high pressures it may increase slightly.
Can I use this calculator for a gas mixture?
No, the calculator assumes a single gas. For mixtures, you need to estimate the effective conductivity using mixing rules (e.g., Wassiljewa equation) or look up measured values for the specific mixture.
What is the thermal conductivity of air at 0 °C?
At 0 °C, air’s conductivity is about 0.024 W/m·K, slightly lower than at 25 °C. As temperature increases, conductivity increases roughly as T^0.8 for air.
How do I convert W/m·K to other units?
1 W/m·K = 0.5778 BTU/(hr·ft·°F) = 0.8598 kcal/(hr·m·°C). For quick conversions, multiply by 0.578 for BTU units.
Why is argon used in windows if it conducts less heat than air?
Argon has lower conductivity (0.0177 vs 0.026 W/m·K), so it reduces conductive heat transfer. It’s also denser than air, which suppresses convection in the gap, further improving insulation.
Related
Formula used
in k | Thermal conductivity (W/m·K) | W/m·K | 0.026 | 0.001 in dt | Temperature difference (K) | K | 50 | 0.001 in th | Thickness of gas layer (m) | m | 0.01 | 0.0001 out q | Heat flux (W/m²) | W/m² | k * dt / th | 1
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- ug to ppb Calculator: Convert Micrograms per Liter1.00 ppb
- Grams to Moles Chemistry: How to Convert0.2000 mol/L
- Convert ug/l to ppb Calculator
- CPP Calculator Ontario: How CPP Is Calculated162.12 $/month
- Grams to Moles to Molecules: How to Convert0.2000 mol/L
- Organic Chemistry Reaction Calculator: How It Works