molecalculator

Moles & Molar Mass

Thermal Conductivity of Oxygen Gas: Value & Meaning

Calculator No. 01-10715 · Updated · Formula and assumptions shown below

Thermal conductivity 0.0101 W/(m·K)
Gas temperature
25 °C
Set in the form below
You enter
Gas temperature (°C)
You get
Thermal conductivity (W/(m·K))
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The thermal conductivity of oxygen gas (O2) at 0 °C and 1 atm is approximately 0.0246 W/(m·K) (watts per meter-kelvin). At 25 °C it rises to about 0.0267 W/(m·K). This value is low compared to metals but typical for a non-metallic gas, and it increases with temperature while being nearly independent of pressure at moderate ranges.

Formula

The calculator uses a practical empirical correlation for oxygen gas over 0–500 °C:

k = 0.0000794 × (T)0.85

where:

  • k = thermal conductivity in W/(m·K)
  • T = absolute temperature in kelvin (K) = °C + 273.15

This is a curve-fit to published data (e.g., NIST standard reference data). It is accurate to roughly ±2% between 0 °C and 500 °C. For example, at 25 °C (298.15 K): k = 0.0000794 × (298.15)0.85 ≈ 0.0267 W/(m·K).

Worked Example

Find the thermal conductivity of oxygen at 25 °C.

  1. Convert temperature to kelvin: T = 25 + 273.15 = 298.15 K
  2. Raise T to the power 0.85: 298.150.85 ≈ 336.5
  3. Multiply by the coefficient: 0.0000794 × 336.5 ≈ 0.02672 W/(m·K)

The calculator rounds to 0.0267 W/(m·K). The same method works for any temperature within the valid range.

Assumptions

  • Pure oxygen gas (not air or a mixture).
  • Pressure near 1 atm; conductivity is essentially independent of pressure for moderate ranges (up to ~10 atm).
  • Gas behaves as a dilute, non-reacting gas; the correlation applies to the gas phase only.
  • No radiation or convection contribution – only conduction through the gas.

Why Oxygen’s Conductivity Matters

Thermal conductivity tells you how quickly heat moves through a material by conduction. For oxygen gas, this property is critical in many real-world applications:

  • Cryogenic systems: Liquid oxygen storage tanks use vacuum insulation because even a small amount of oxygen gas conducts heat noticeably.
  • Combustion and flames: In oxy-fuel cutting or welding, oxygen’s conductivity affects flame temperature and heat transfer.
  • Respiratory and medical gas lines: Though not the primary concern, thermal conductivity is considered in designing heat exchangers for gas warming.
  • Semiconductor manufacturing: Oxygen plasma and gas-phase processes require accurate thermal modeling.

Compared to other common gases at 25 °C: nitrogen is about 0.0257 W/(m·K), air ~0.0262, helium ~0.151, and argon ~0.0177. Oxygen is a middling conductor among gases – much better than argon but far worse than helium.

How Temperature and Pressure Change It

For gases, thermal conductivity rises with temperature because molecules move faster and transfer kinetic energy more readily. Over 0–500 °C, oxygen’s conductivity roughly doubles. Pressure has a negligible effect below about 10 atm because the mean free path is much smaller than typical container dimensions; at very low pressures (vacuum), conductivity drops dramatically as collisions become rare.

Common Misconception: “Oxygen is Highly Conductive”

Some assume that because oxygen supports combustion and is used in high-temperature processes, it must be an excellent heat conductor. In fact, oxygen gas is a poor conductor – about 10,000 times worse than copper (copper ~400 W/(m·K)). What oxygen does is react exothermically with fuels, releasing heat; it does not conduct heat well itself. The confusion arises because hot oxygen gas can carry heat by convection (mass movement) in furnaces, but that is a different mechanism.

How to Use the Calculator and Read Results

Enter the gas temperature in °C. The output is the thermal conductivity in W/(m·K). Use it for:

  • Estimating heat loss through a gas layer (e.g., in double-pane windows with oxygen? – unlikely, but for any gas-filled gap).
  • Designing heat exchangers where oxygen is the working fluid.
  • Checking whether a material’s insulation is adequate.

For a rough heat transfer calculation, combine k with the temperature gradient and area using Fourier’s law: Q = k·A·(ΔT/d), where Q is heat flow (W), A is area (m²), ΔT is temperature difference (K), and d is thickness (m).

Limitations and Accuracy

The correlation is a fit to experimental data and may deviate at very high temperatures (above 500 °C) where dissociation of O2 into oxygen atoms begins. At cryogenic temperatures (below 0 °C), the power-law fit is less accurate; use tabulated data from NIST for precise work. Also, the formula assumes pure oxygen – even small amounts of water vapor or other gases alter the conductivity.

Frequently Asked Questions

What is the thermal conductivity of oxygen at room temperature?

At 25 °C (298 K), pure oxygen gas has a thermal conductivity of about 0.0267 W/(m·K). This is a standard reference value used in engineering handbooks.

Does oxygen conduct heat better than air?

Yes, slightly. At 25 °C, air has a thermal conductivity of about 0.0262 W/(m·K), while oxygen is about 0.0267 W/(m·K). The difference is small because air is mostly nitrogen (0.0257) with oxygen mixed in.

Why is oxygen’s thermal conductivity lower than helium’s?

Helium atoms are much lighter than oxygen molecules (molar mass 4 vs 32 g/mol). Lighter molecules move faster at the same temperature, so they transfer kinetic energy more efficiently, giving helium a much higher thermal conductivity (~0.151 W/(m·K)).

Does pressure affect the thermal conductivity of oxygen?

At moderate pressures (1–10 atm), the effect is negligible. However, at very low pressures (vacuum), thermal conductivity drops dramatically. At very high pressures (above 100 atm), it starts to increase slightly because molecular interactions become significant.

How does oxygen’s conductivity compare to that of liquid oxygen?

Liquid oxygen has a much higher thermal conductivity – about 0.15 W/(m·K) at its boiling point (-183 °C). That’s roughly 6 times higher than the gas at 25 °C, because molecules are densely packed in the liquid phase.

Can I use this calculator for oxygen-enriched air?

No. The calculator is for pure oxygen. For mixtures like air (21% O2), use the conductivity of air (~0.0262 W/(m·K) at 25 °C). For other mixtures, you would need mixing rules that account for composition.

Related

Formula used
in t | Gas temperature | °C | 25 | -273.15 | 2000
out k | Thermal conductivity | W/(m·K) | 0.0000794 * (t + 273.15) ^ 0.85 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →