molecalculator

Moles & Molar Mass

Thermal Conductivity to U-Value Calculator

Calculator No. 01-10372 · Updated · Formula and assumptions shown below

U-value 0.350 W/m²·K
R-value
2.857 m²·K/W
= Thickness ÷ Thermal conductivity (k)
Thermal conductivity (k)
0.035 W/m·K
Set in the form below
Thickness
0.1 m
Set in the form below
You enter
Thermal conductivity (k) (W/m·K), Thickness (m)
You get
U-value (W/m²·K), R-value (m²·K/W)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts a material’s thermal conductivity (k, in W/m·K) and thickness (in meters) into a U-value (in W/m²·K), which measures how well heat passes through a building element. You enter the conductivity and thickness, and the calculator returns the U-value, the reciprocal of the R-value. The U-value is the standard metric for heat loss through walls, roofs, and windows, and lower values mean better insulation.

Formula

The U-value (thermal transmittance) is the inverse of the total thermal resistance (R-value) of a building element. For a single homogeneous layer, the formula is:

U = k / d

  • U – thermal transmittance in W/m²·K (watts per square metre per kelvin)
  • k – thermal conductivity in W/m·K (watts per metre per kelvin)
  • d – thickness in metres (m)

The R-value is the reciprocal: R = d / k, and U = 1/R. For multi-layer assemblies, the total R is the sum of each layer’s R, and the overall U is 1 / (sum of R-values).

Worked Example

Using the default values from the calculator: a mineral wool insulation board with thermal conductivity k = 0.035 W/m·K and thickness d = 0.10 m.

Step 1: Calculate the R-value: R = d / k = 0.10 / 0.035 = 2.857 m²·K/W.

Step 2: Calculate the U-value: U = 1 / R = 1 / 2.857 = 0.350 W/m²·K.

So the U-value is approximately 0.35 W/m²·K, which is a typical value for a well-insulated wall. The calculator’s formula gives the same result: 0.035 / 0.10 = 0.35.

Assumptions

  • Steady-state heat flow (no thermal mass effects).
  • One-dimensional heat transfer perpendicular to the surface.
  • The material is homogeneous and isotropic (same k in all directions).
  • No air gaps, thermal bridges, or surface resistances are included.
  • Values are for the material itself, not the whole wall assembly.

How to Use the Calculator

To convert thermal conductivity to U-value, you need two numbers:

  1. Thermal conductivity (k) – usually found on the product datasheet or in material property tables. Common values: mineral wool 0.030–0.045, EPS foam 0.030–0.040, concrete 1.0–1.8, glass 1.0, wood 0.12–0.15 W/m·K.
  2. Thickness (d) – the actual thickness of the insulation layer in metres. Convert from millimetres by dividing by 1000 (e.g., 150 mm = 0.15 m).

Enter both values, and the calculator gives the U-value (first output) and the R-value (second output). If you have a multi-layer wall, calculate each layer’s R separately, add them, then take the reciprocal to get the total U.

Why U-Value Matters in Building Design

U-values are used in building regulations and energy codes worldwide to set maximum allowed heat loss through building elements. For example, many European building codes require wall U-values below 0.30 W/m²·K, while some passive house standards demand below 0.15 W/m²·K. The lower the U-value, the less heat escapes in winter or enters in summer, reducing energy consumption and heating/cooling costs.

The U-value also determines the heat loss rate: Heat loss (W) = U × Area (m²) × Temperature difference (K). For instance, a 20 m² wall with U = 0.35 and a 20°C indoor-outdoor difference loses 0.35 × 20 × 20 = 140 watts.

Common Mistakes and Misconceptions

  • Confusing k and U: k is a material property (per metre thickness), while U is a property of a specific thickness of that material. A thick layer of a mediocre insulator can have a lower U than a thin layer of a good insulator.
  • Unit errors: Thickness must be in metres, not millimetres or centimetres. 50 mm is 0.05 m, not 50 m.
  • Ignoring surface resistances: Real walls have air films on both sides that add to the total R. The calculator gives the material-only U; the whole assembly U will be slightly higher (better) because surface resistances add to R.
  • Assuming U is the same as R: U = 1/R, not R. A high R means a low U.

Limitations of the Simple Formula

The formula U = k/d assumes a single, homogeneous layer. Real building elements often have multiple layers, air gaps, studs, and fasteners that create thermal bridges. For accurate whole-wall U-values, you need to account for these using more complex methods or software. Also, thermal conductivity varies with temperature and moisture content; the datasheet value is usually for dry material at 10–25°C. The calculator is for planning and comparison, not for final building certification.

Frequently Asked Questions

How do I convert U-value to R-value?
Simply take the reciprocal: R = 1/U. For example, U = 0.35 W/m²·K gives R = 1/0.35 = 2.86 m²·K/W.

What is a good U-value for a wall?
It depends on your climate and building code. In cold climates, aim for U ≤ 0.30 W/m²·K for walls; passive house standards require U ≤ 0.15. For roofs, lower values are common because heat rises.

Can I use this calculator for windows?
No, windows have multiple components (glass, frames, gas fills) and are rated as a whole assembly. The calculator is for single homogeneous materials like insulation boards.

What is the difference between thermal conductivity and thermal transmittance?
Thermal conductivity (k) is a material property independent of thickness. Thermal transmittance (U) is the heat flow through a specific thickness of that material. k is measured in W/m·K, U in W/m²·K.

Does adding more insulation always lower the U-value?
Yes, but not linearly. Doubling the thickness halves the U-value (since U = k/d). However, cost and space constraints often make very thick insulation impractical.

Related

Formula used
in k | Thermal conductivity (k) | W/m·K | 0.035 | 0.001 | 100
in t | Thickness | m | 0.1 | 0.001 | 10
out u | U-value | W/m²·K | k / t | 3
out r | R-value | m²·K/W | t / k | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →