molecalculator

Moles & Molar Mass

Thermal Expansion Calculation for Pipe

Calculator No. 01-8868 · Updated · Formula and assumptions shown below

Length change 6.00 mm
Length change
0.236 in
= (Expansion coefficient α × Pipe length × Temperature change ΔT) × 39.3701
Pipe length
10 m
Set in the form below
Expansion coefficient α
0.000012 1/°C
Set in the form below
You enter
Pipe length (m), Expansion coefficient α (1/°C), Temperature change ΔT (°C)
You get
Length change (mm), Length change (in)
Rounding
2 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To calculate thermal expansion of a pipe, use ΔL = α × L₀ × ΔT, where ΔL is the change in length (in meters), α is the linear expansion coefficient of the pipe material (in 1/°C), L₀ is the original pipe length (in meters), and ΔT is the temperature change (in °C). Enter these three values below to get the expansion or contraction in millimeters and inches.

Formula

The linear thermal expansion formula is:

ΔL = α × L₀ × ΔT

  • ΔL = change in length (m or mm)
  • α = coefficient of linear thermal expansion (1/°C, also written as °C⁻¹)
  • L₀ = original length of the pipe (m)
  • ΔT = temperature change (T_final – T_initial, in °C)

For example, carbon steel has α ≈ 12 × 10⁻⁶ /°C (0.000012 /°C), stainless steel ≈ 17 × 10⁻⁶ /°C, copper ≈ 17 × 10⁻⁶ /°C, aluminum ≈ 23 × 10⁻⁶ /°C, and PVC ≈ 80 × 10⁻⁶ /°C. These values are typical at room temperature; they vary slightly with temperature range.

Worked Example

Using the default values from the calculator: a 10 m carbon steel pipe (α = 0.000012 /°C) experiences a temperature rise of 50 °C.

  1. Multiply the coefficient by the length: 0.000012 × 10 = 0.00012 m per °C.
  2. Multiply by the temperature change: 0.00012 × 50 = 0.006 m.
  3. Convert to millimeters: 0.006 m × 1000 = 6.00 mm.
  4. Convert to inches: 0.006 m × 39.3701 = 0.236 in.

The pipe expands by 6.00 mm (0.236 in) along its entire length. The calculator gives the same result: 6.00 mm and 0.236 in.

Assumptions

  • The pipe is free to expand (no restraints).
  • The temperature change is uniform along the whole length.
  • The expansion coefficient is constant over the temperature range (true for most metals over modest ΔT).
  • The pipe is not under internal pressure that would cause additional strain.

Why Pipe Thermal Expansion Matters

Pipes are long, rigid structures. A 30 m steel pipe carrying hot water at 90 °C in a plant that was installed at 20 °C will expand by about 25 mm. If that expansion is not accommodated, the pipe will push against supports, flanges, or equipment, causing stress, bending, or failure. In long pipelines, thermal expansion is a primary design consideration. The calculation tells you how much movement to expect so you can design expansion loops, bellows, or sliding supports.

How to Choose the Expansion Coefficient

The coefficient α depends on the pipe material. For a quick estimate, use these typical values (all in 1/°C):

  • Carbon steel: 12 × 10⁻⁶
  • Stainless steel (austenitic): 17 × 10⁻⁶
  • Copper: 17 × 10⁻⁶
  • Aluminum: 23 × 10⁻⁶
  • PVC: 80 × 10⁻⁶
  • Polyethylene (PE): 200 × 10⁻⁶

For precise engineering work, look up the exact coefficient for your alloy in the material datasheet or a reference like ASME B31.1 or B31.3. Note that the coefficient itself changes with temperature, but for most design calculations a single average value over the expected range is sufficient.

Common Mistakes and Misconceptions

  • Using °F instead of °C: The formula requires consistent units. If you have ΔT in °F, convert to °C (ΔT°C = ΔT°F × 5/9).
  • Forgetting that ΔT is a difference: Use the absolute temperature change, not the final temperature alone. A pipe going from 20 °C to 70 °C has ΔT = 50 °C, not 70 °C.
  • Mixing up α units: Some tables give α in 10⁻⁶ /°C (e.g., 12 for steel). If you enter 12 instead of 0.000012, you’ll get a result 1,000,000 times too large.
  • Ignoring the pipe’s constraints: The formula gives free expansion. If the pipe is anchored at both ends, it will not expand; instead, thermal stress develops. The stress can be estimated as σ = E × α × ΔT, where E is the modulus of elasticity.

What to Do with the Result

Once you know the expansion, you decide how to manage it. For short pipe runs (less than about 10 m), expansion may be absorbed by natural flexibility in bends. For longer runs, you might need:

  • Expansion loops (U-shaped bends) that flex to absorb movement.
  • Bellows or expansion joints that allow axial movement.
  • Sliding pipe supports that let the pipe move freely.
  • Anchors placed at strategic points to direct expansion toward the flexible elements.

The calculated ΔL tells you the required travel of the expansion joint or the size of the loop. For example, a 6 mm expansion may be handled by a small bellows, while 50 mm might need a large loop or multiple joints.

Cost and Material Considerations

Thermal expansion affects cost indirectly. Pipes with higher expansion coefficients (like plastics) require more expansion loops or joints, which add material and labor. Metals like steel have lower expansion, but they are heavier and may need more supports. When comparing materials, include the cost of expansion compensation in the total. For instance, PVC is cheap per meter but may need many expansion loops in a long run, while steel may need fewer loops but costs more per meter. The calculation helps you quantify the movement, which directly influences the number of loops and joints needed.

Limits of the Simple Formula

The linear formula is accurate for most piping systems, but it has limits:

  • It assumes the pipe is unrestrained. If the pipe is rigidly fixed, thermal stress dominates, not expansion.
  • It ignores the effect of internal pressure, which can cause additional expansion (hoop strain) and longitudinal strain.
  • It assumes a uniform temperature. In reality, a pipe may have temperature gradients along its length, especially during startup or shutdown.
  • For very high temperatures (above about 500 °C for steel), the expansion coefficient changes significantly, and creep may occur.

For critical applications, engineers use finite element analysis or piping stress analysis software, but the simple formula remains the first check for sizing and layout.

Frequently Asked Questions

How much does a 100-foot steel pipe expand with a 100°F temperature rise?

First convert to SI: 100 ft = 30.48 m, 100°F change = 55.56°C. Using α = 0.000012 /°C, ΔL = 0.000012 × 30.48 × 55.56 = 0.0203 m = 20.3 mm (about 0.8 inches). That’s a significant movement for a straight run.

What is the thermal expansion coefficient of PVC pipe?

PVC has a coefficient of about 80 × 10⁻⁶ /°C (0.00008 /°C). That’s roughly 6–7 times that of steel, meaning a 10 m PVC pipe expands about 40 mm for a 50 °C rise, compared to 6 mm for steel.

Does the pipe diameter affect thermal expansion?

No, the linear expansion along the length is independent of diameter. The formula uses only length, material, and temperature change. However, diameter does affect the expansion in the radial direction (which is usually negligible for piping) and the stiffness of the pipe, which influences how the expansion is accommodated.

What is the difference between expansion and thermal stress?

Expansion is the physical change in length when the pipe is free to move. Thermal stress occurs when the pipe is restrained and cannot expand. The stress is calculated as σ = E × α × ΔT, where E is the elastic modulus. For a steel pipe (E ≈ 200 GPa) with ΔT = 50 °C, the stress would be 200 × 10⁹ × 0.000012 × 50 = 120 MPa, which is close to the yield strength of mild steel. That’s why anchors must be designed carefully.

Can I use the same formula for pipe contraction when cooling?

Yes. The formula works for both expansion and contraction. If ΔT is negative (cooling), ΔL will be negative, indicating shrinkage. The magnitude is the same for a given absolute temperature change, assuming the coefficient is constant over that range.

How do I account for thermal expansion in a pipe that is not straight?

For a pipe with bends, the total expansion is the sum of the expansions along each straight segment, but the bends themselves absorb some of the movement. In practice, engineers calculate the expansion of the longest straight run between anchors and design the bends to flex. The simple formula gives the free expansion of that run, which is the starting point for loop sizing.

Related

Formula used
in m | Pipe length | m | 10 | 0
in a | Expansion coefficient α | 1/°C | 0.000012 | 0
in d | Temperature change ΔT | °C | 50 | 0
out dl | Length change | mm | (a * m * d) * 1000 | 2
out dli | Length change | in | (a * m * d) * 39.3701 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →