molecalculator

Moles & Molar Mass

Thermal Expansion Calculation Formula

Calculator No. 01-8869 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The thermal expansion calculation formula is ΔL = α × L₀ × ΔT for linear expansion, where ΔL is the change in length, α is the coefficient of linear expansion, L₀ is the original length, and ΔT is the temperature change. For volume expansion, use ΔV = β × V₀ × ΔT, where β is the coefficient of volume expansion (β ≈ 3α for isotropic solids). This page provides a calculator that computes the change in length or volume for a given material, original dimension, and temperature change, returning the expansion amount and the final dimension.

Formula

The linear thermal expansion formula is:

ΔL = α × L₀ × ΔT

  • ΔL – change in length (meters, m)
  • α – coefficient of linear expansion (per °C or per K; for most materials, values are on the order of 10-6 /°C)
  • L₀ – original length (m)
  • ΔT – temperature change (°C or K; the same numerical value because a change of 1 °C equals a change of 1 K)

For volume expansion, the analogous formula is ΔV = β × V₀ × ΔT, where β is the coefficient of volume expansion. For isotropic solids, β ≈ 3α. For liquids and gases, β is given directly (e.g., water at 20 °C has β ≈ 207 × 10-6 /°C).

Worked Example

Using the default values from the calculator: aluminum (α = 23 × 10-6 /°C), original length L₀ = 2.000 m, temperature change ΔT = 50 °C.

  1. Write the formula: ΔL = α × L₀ × ΔT
  2. Substitute: ΔL = (23 × 10-6 /°C) × 2.000 m × 50 °C
  3. Multiply: ΔL = 23 × 10-6 × 100 = 0.0023 m
  4. Final length: L = 2.000 + 0.0023 = 2.0023 m

The calculator shows ΔL = 0.002300 m and L = 2.0023 m, matching the hand calculation.

Assumptions

  • The material is homogeneous and isotropic (properties same in all directions).
  • The temperature change is uniform throughout the object.
  • The coefficient α is constant over the temperature range; in reality, α varies slightly with temperature.
  • No phase change occurs (solid stays solid, liquid stays liquid).
  • For volume expansion of solids, β ≈ 3α is an approximation valid for isotropic materials.

How to Choose the Right Coefficient

The coefficient α depends on the material and, to a lesser extent, on temperature. For engineering calculations, use published values for the specific alloy or grade. For example:

  • Aluminum (6061 alloy): ~23 × 10-6 /°C
  • Steel (mild): ~12 × 10-6 /°C
  • Concrete: ~12 × 10-6 /°C (varies with mix)
  • Glass (soda-lime): ~9 × 10-6 /°C
  • Copper: ~17 × 10-6 /°C
  • Brass: ~19 × 10-6 /°C

If your material is not listed, look up its coefficient from a reliable engineering reference. For anisotropic materials (e.g., wood, composites), you may need different coefficients for different directions.

Common Mistakes and Pitfalls

  • Mixing up α and β: For solids, β ≈ 3α, but for liquids you must use the liquid’s β directly. Using α for a liquid will give a wildly wrong answer.
  • Unit inconsistency: Ensure L₀ and ΔL are in the same unit (e.g., meters). If L₀ is in millimeters, ΔL will be in millimeters. The calculator uses meters, but you can convert manually.
  • Temperature scale: ΔT is a difference, so °C and K are interchangeable. Do not add 273.15 when computing ΔT.
  • Sign of ΔT: If temperature decreases, ΔT is negative, and ΔL becomes negative (contraction). The calculator handles negative ΔT correctly.
  • Ignoring constraints: In real structures, thermal expansion may be constrained, causing stress rather than free expansion. The formula gives free expansion only.

Applications and Real-World Context

Thermal expansion calculations are essential in many fields:

  • Civil engineering: Expansion joints in bridges and railways accommodate length changes due to temperature swings.
  • Mechanical design: Pistons, engine blocks, and precision instruments must account for thermal expansion to maintain clearances.
  • Electrical engineering: Overhead power lines sag more in summer because the conductors expand.
  • Jewelry and metalwork: Rings and fittings are sized considering thermal expansion to avoid seizing.
  • Thermometers: Liquid-in-glass thermometers rely on the volume expansion of mercury or alcohol.

For a bridge of length 100 m made of steel (α = 12 × 10-6 /°C), a temperature change of 40 °C (from -10 °C to 30 °C) would cause a length change of ΔL = 12 × 10-6 × 100 × 40 = 0.048 m (4.8 cm). This is why expansion joints are critical.

Limits of the Formula

The linear formula is accurate for small temperature changes where α is nearly constant. For large temperature ranges (e.g., from cryogenic to high temperatures), α varies significantly, and a more accurate calculation integrates α(T) over the temperature range. Also, the formula assumes free expansion; if the object is constrained, thermal stress develops, and the actual deformation is less than the free expansion. For anisotropic materials, the expansion depends on direction, and a tensor treatment may be needed.

Frequently Asked Questions

What is the coefficient of thermal expansion for water?

Water has a coefficient of volume expansion β of about 207 × 10-6 /°C at 20 °C, but it is not constant. Water is unusual: it expands when heated from 0 to 4 °C (actually contracts), then expands above 4 °C. This anomaly is why ice floats.

Does thermal expansion apply to gases?

Yes, gases expand significantly with temperature. For an ideal gas at constant pressure, the volume change is given by the ideal gas law: V/T = constant. The coefficient of volume expansion for an ideal gas is approximately 1/273 per °C at 0 °C, but it varies with temperature and pressure.

How do I calculate thermal expansion for a hole or a ring?

For a hole in a solid, the hole expands as if it were filled with the same material. So the inner diameter of a ring expands according to the same linear formula using the same α. For example, a steel ring with inner diameter 50 mm heated by 100 °C will increase by ΔD = 12 × 10-6 × 50 × 100 = 0.06 mm.

What is the difference between linear and volumetric expansion?

Linear expansion refers to a single dimension (length, width, height). Volumetric expansion refers to the total volume. For isotropic solids, the volume coefficient β is approximately 3α. For liquids, only volumetric expansion is usually defined because they take the shape of their container.

Why do railroad tracks have gaps?

Railroad tracks have small gaps between sections to allow for thermal expansion. Without gaps, the tracks would buckle on hot days. The gap size is calculated using the linear expansion formula, considering the maximum expected temperature range.

Related

Formula used
in sel | Material | Aluminum=23e-6, Steel=12e-6, Concrete=12e-6, Glass=9e-6, Copper=17e-6, Brass=19e-6, Iron=12e-6, Wood=4e-6
in m | Original length (L₀) | m | 2.000 | 0
in dt | Temperature change (ΔT) | °C | 50 | -273.15
out dl | Change in length (ΔL) | m | m * sel * dt | 6
out lf | Final length (L) | m | m + dl | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →