molecalculator

Moles & Molar Mass

Thermal Expansion Equation: Diameter Change

Calculator No. 01-8874 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To find the change in diameter of an object due to temperature change, use the linear thermal expansion equation: ΔL = α × L₀ × ΔT, where L₀ is the original diameter, ΔT is the temperature change, and α is the coefficient of linear expansion. The new diameter is simply L₀ + ΔL. This page provides a calculator that applies this equation to diameter changes, along with the background, formula, and practical considerations you need.

Formula

The linear thermal expansion equation is:

ΔL = α × L₀ × ΔT

Where:

  • ΔL = change in length (or diameter) in meters (m)
  • α = coefficient of linear expansion in 1/°C (or 1/K, since the size of a degree is the same)
  • L₀ = original length (or diameter) in meters (m)
  • ΔT = temperature change in °C or K (T_final − T_initial)

The new length (or diameter) is:

L = L₀ + ΔL = L₀ × (1 + α × ΔT)

This equation works for any linear dimension of an object—length, width, height, or diameter—as long as the material is homogeneous and the temperature change is uniform.

Worked Example

Using the calculator defaults: a steel rod with an original diameter of 0.050 m (50 mm), α = 12 × 10⁻⁶ /°C (typical for steel), and a temperature increase of 40 °C.

Step 1: Plug into the formula:

ΔL = 12 × 10⁻⁶ × 0.050 × 40

Step 2: Multiply α × L₀:

12 × 10⁻⁶ × 0.050 = 6.0 × 10⁻⁷ m/°C

Step 3: Multiply by ΔT:

6.0 × 10⁻⁷ × 40 = 2.4 × 10⁻⁵ m = 0.000024 m = 0.024 mm

So the diameter increases by 0.024 mm. The new diameter is 0.050024 m (50.024 mm). The calculator shows the same result.

Assumptions

  • The material is homogeneous and isotropic (same properties in all directions).
  • The temperature change is uniform throughout the object.
  • The coefficient α is constant over the temperature range (true for small ΔT, typically less than 100 °C for metals).
  • No phase change occurs (e.g., solid to liquid).
  • The object is free to expand—no external constraint that would cause stress.

Why Diameter Matters in Real Applications

Diameter changes are critical in engineering and manufacturing. For example, a steel axle with a nominal diameter of 50 mm at 20 °C will expand to about 50.024 mm at 60 °C. If the axle fits into a bearing with a clearance of only 0.01 mm, the expansion could cause seizure. Conversely, when cooling a shaft to fit it into a hub (shrink fitting), engineers calculate the exact temperature drop needed to achieve a specific interference fit. The same equation applies to pipes, wires, and holes—any circular cross-section.

How to Choose the Right Coefficient (α)

The coefficient of linear expansion varies by material. Here are typical values (in 1/°C × 10⁻⁶):

  • Aluminum: 23
  • Copper: 17
  • Steel (mild): 12
  • Concrete: 10–14
  • Glass (Pyrex): 3.2
  • Invar (nickel-iron alloy): 1.2

For precise work, look up the exact value for your specific alloy, as it can vary. For example, stainless steel may range from 9 to 17 × 10⁻⁶ /°C depending on grade. If you are working with a composite or anisotropic material (like wood or fiberglass), the expansion may differ along different axes—use the value for the direction you care about.

Common Mistakes and How to Avoid Them

  • Unit mix-ups: Ensure L₀ is in meters if you want the result in meters. If you input millimeters, the output will be in millimeters—but the calculator expects meters, so convert first (1 mm = 0.001 m).
  • Using diameter vs. radius: The equation works for any linear dimension, but be consistent. If you input the radius, the output is the change in radius, not diameter.
  • Forgetting that ΔT is a difference: If the temperature goes from 20 °C to 60 °C, ΔT = 40 °C, not 60 °C. Also, a change of 1 °C equals a change of 1 K, so you can mix units as long as you use a difference.
  • Ignoring signs: Cooling gives a negative ΔT, so ΔL is negative (contraction). The calculator allows negative ΔT, but make sure you enter the correct sign.
  • Assuming α is constant over large ranges: For temperature changes over hundreds of degrees, α can vary. Use an average value over the range, or a more complex model if needed.

Limitations of the Linear Equation

The linear equation is an approximation that holds well for small temperature changes. For large ΔT, the expansion is actually exponential, but the linear term dominates. The error is roughly (αΔT)²/2; for steel with ΔT = 100 °C, that’s about 0.007%—negligible. However, for materials with very high α (e.g., plastics like nylon, α ≈ 80 × 10⁻⁶ /°C) and large ΔT, the error can reach a few percent. In such cases, use the more accurate formula:

L = L₀ × e^(αΔT) (exponential form)

But for most engineering and lab applications, the linear equation is sufficient.

Practical Tips for Using the Calculator

  • Enter the original diameter in meters (e.g., 0.05 for 50 mm). If you have a measurement in inches, convert: 1 inch = 0.0254 m.
  • Use the coefficient α in 1/°C. If you have a value in 1/K, it’s numerically the same.
  • Enter the temperature change (final − initial) in °C. A positive value means heating, negative means cooling.
  • The result shows the change in diameter and the new diameter. For a hole (e.g., in a plate), the same calculation gives the change in hole diameter—it expands exactly like the solid material.

Frequently Asked Questions

Does the diameter of a hole expand or contract when heated?

A hole expands when the material is heated, just like the solid material around it. This is counterintuitive, but the atoms in the ring of material move further apart, increasing the circumference and thus the diameter. The equation applies to the hole’s diameter with the same α.

Can I use this equation for area or volume expansion?

No. For area expansion, use ΔA = 2α × A₀ × ΔT (approximately). For volume expansion, use ΔV = β × V₀ × ΔT, where β ≈ 3α for isotropic solids. The factor of 2 or 3 comes from expansion in multiple dimensions.

What is the coefficient of linear expansion for water?

Water is a liquid and does not have a linear expansion coefficient in the same sense. Liquids expand volumetrically. For water, the volumetric expansion coefficient is about 0.000214 /°C at 20 °C, but it varies with temperature and is anomalous near 4 °C (water contracts when heated from 0 to 4 °C).

Why do some materials expand more than others?

Expansion is related to the strength of interatomic bonds. Materials with strong bonds (like diamond or Invar) have low α because atoms vibrate less and stay closer. Materials with weak bonds (like plastics or lead) have high α. The atomic structure also matters—for example, polymers have long chains that can flex, leading to larger expansion.

How do I account for thermal expansion in a bolted joint?

For a bolted joint, you need to consider the expansion of both the bolt and the materials being clamped. If the bolt and the clamped parts have different α values, the preload can change with temperature. Use the linear equation for each component and calculate the differential expansion. This is critical in engines and bridges, where thermal cycling can loosen or over-stress fasteners.

Is the coefficient α the same for all directions in a metal?

For most metals, yes—they are isotropic. But some materials, like wood, fiberglass composites, or certain crystals, are anisotropic: they expand differently along different axes. In such cases, you need different α values for each direction. For rolled metals, there can be slight anisotropy, but it’s often negligible.

Safety and Scope

This calculator is for engineering and physics calculations. Always verify your results with real measurements, especially in safety-critical applications like shrink fits or precision assemblies. For laboratory work, follow your lab method, the safety data sheet (SDS) and your supervisor. Thermal expansion can cause stress and failure if parts are constrained—always account for it in design.

Related

Formula used
in d0 | Original diameter | m | 0.050 | 0
in a | Coefficient of linear expansion (α) | 1/°C | 0.000012 | 0
in dt | Temperature change (ΔT) | °C | 40 | -273.15
out dl | Change in diameter (ΔL) | m | a * d0 * dt | 7
out d1 | New diameter | m | d0 + a * d0 * dt | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →