“Uh to h conversion” refers to converting a measurement of inductance from microhenries (µH, sometimes written as “uh”) to henries (H), the SI unit of inductance. To convert, divide the value in microhenries by 1,000,000 (or multiply by 1 × 10−6). For example, 10 µH = 0.00001 H.
Formula
The conversion is a simple power-of-ten scaling:
H = µH ÷ 1,000,000
where:
- H = inductance in henries (H)
- µH = inductance in microhenries (µH)
Since the prefix “micro” (µ) means one-millionth (10−6), you are moving the decimal point six places to the left. The same logic applies to millihenries (mH): 1 mH = 1,000 µH, so dividing by 1,000 converts µH to mH.
Worked Example
Using the default value of 10 µH from the calculator:
- Start with the value: 10 µH.
- Divide by 1,000,000: 10 ÷ 1,000,000 = 0.00001 H.
- For millihenries: 10 ÷ 1,000 = 0.01 mH.
The calculator shows 0.000010 H (rounded to 6 decimals) and 0.010 mH (rounded to 3 decimals).
Assumptions
- The conversion is exact and assumes standard SI prefix definitions.
- The value is a pure inductance magnitude; no frequency, resistance, or core properties are involved.
- “uh” is treated as a common informal abbreviation for microhenries (µH), not as a separate unit.
Why This Conversion Matters
Inductors in real circuits are almost never labeled in whole henries. A typical power-supply choke might be 100 µH; a radio-frequency coil could be 1–10 µH; a small signal filter inductor might be 470 nH (nanhenries, 0.47 µH). Henries are reserved for large, heavy components like transformer primaries or speaker crossover inductors, which can be several henries. When you read a schematic, the component value is often given in µH, but calculations for resonant frequency, impedance, or energy storage require the value in henries because the standard formulas use SI base units.
How to Do the Conversion Without a Calculator
Because it is only a decimal shift, you can do it mentally:
- µH to H: move the decimal point six places left. Example: 2,500 µH → 0.0025 H.
- µH to mH: move the decimal point three places left. Example: 2,500 µH → 2.5 mH.
- H to µH: move the decimal point six places right. Example: 0.004 H → 4,000 µH.
If you are converting from nanogenries (nH), remember 1,000 nH = 1 µH, so first convert nH to µH by dividing by 1,000, then to H by dividing by another 1,000,000.
Common Mistakes and Misconceptions
The most frequent error is confusing microhenries with millihenries. A 100 mH inductor is 100,000 µH, not 0.1 µH. Always check the prefix on the part or schematic before converting. Another common mistake is using the wrong power of ten: some people divide by 1,000 instead of 1,000,000 when going to henries, which yields a result 1,000 times too large.
Also, note that “uh” is not an official SI symbol. The correct symbol is µH (Greek letter mu followed by H). Some older schematics or datasheets may write “uH” (using a lowercase u as a substitute for µ), which means the same thing. Do not confuse it with “UH” (uppercase) which is not a standard unit abbreviation.
Where You Will Actually Use This
Three common calculations require inductance in henries:
- Resonant frequency of an LC circuit: f = 1 / (2π√(LC)), where L is in henries and C in farads. If you plug in µH and pF without converting, the answer will be off by a factor of 106.
- Inductive reactance: XL = 2πfL, where f is in hertz and L in henries. At 1 MHz, a 10 µH inductor has XL ≈ 62.8 Ω; using 10 H would give 62.8 MΩ.
- Energy stored in an inductor: E = ½LI², where L is in henries and I in amperes. For a 100 µH inductor carrying 2 A, the energy is ½ × 0.0001 × 4 = 0.0002 J (200 µJ).
In all three, the formula assumes SI units, so converting µH to H first is mandatory for a correct result.
Practical Component Values
To give you a sense of scale, here are typical real-world inductors and their values in henries:
- Small surface-mount RF inductor: 1–100 nH (0.000001–0.0001 mH)
- Common through-hole power inductor: 10–1,000 µH (0.00001–0.001 H)
- Speaker crossover coil: 0.5–10 mH (0.0005–0.01 H)
- Large mains transformer primary (magnetizing inductance): 1–10 H
When ordering parts, always match the unit printed on the schematic. A 10 µH inductor is a small component; a 10 H inductor is a heavy, bulky part with hundreds of turns of wire.
Frequently Asked Questions
Is 1 µH equal to 0.001 mH?
Yes. The milli prefix means one-thousandth, so 1 mH = 1,000 µH. Therefore 1 µH = 0.001 mH.
Why do some datasheets write “uH” instead of “µH”?
Because the Greek letter mu (µ) is not always available on keyboards or in older text encoding, many manufacturers substitute a lowercase “u” which looks similar. Both mean microhenries.
Can I convert µH to H by multiplying by 10⁻⁶?
Yes, that is the same operation. Multiplying by 10⁻⁶ is mathematically identical to dividing by 1,000,000.
What is the difference between µH and mH in practical terms?
They differ by a factor of 1,000. A 1 mH inductor is 1,000 times more inductive than a 1 µH inductor. In a resonant circuit, a 1 mH inductor with a given capacitor resonates at a frequency about 31.6 times lower than a 1 µH inductor with the same capacitor.
Does the conversion change with frequency or current?
No. The conversion is a pure unit scaling. However, the effective inductance of a real inductor can change with frequency (due to core losses and parasitic capacitance) and with DC current (due to core saturation), but that is a property of the component, not the unit conversion.
How do I convert henries back to microhenries?
Multiply the value in henries by 1,000,000. For example, 0.002 H × 1,000,000 = 2,000 µH.
Related
Formula used
in uh | Inductance in microhenries (µH) | µH | 10 | 0 out h | Inductance in henries (H) | H | uh / 1000000 | 6 out mh | Inductance in millihenries (mH) | mH | uh / 1000 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- ug to ppb Calculator: Convert Micrograms per Liter1.00 ppb
- Grams to Moles Chemistry: How to Convert0.2000 mol/L
- Convert ug/l to ppb Calculator
- CPP Calculator Ontario: How CPP Is Calculated162.12 $/month
- Grams to Moles to Molecules: How to Convert0.2000 mol/L
- Organic Chemistry Reaction Calculator: How It Works