A standard PCR tube holds 0.2 mL (200 µL), which is the industry-wide volume for most thermal cyclers. You will also find 0.5 mL and 0.1 mL (100 µL) tubes, but the 0.2 mL size is the default for routine PCR, qPCR, and RT-PCR reactions.
Formula
The calculator above computes the total liquid volume you need to prepare for a set of PCR reactions, including a safety overfill. The formula is:
Total volume (µL) = Reaction volume (µL) × Number of reactions × (1 + Overfill fraction)
- Reaction volume (v) – the volume of one PCR reaction, typically 10–50 µL, entered in microliters (µL).
- Number of reactions (n) – how many individual tubes or wells you are filling.
- Overfill allowance (o) – extra volume to cover pipetting loss, usually 10% (entered as a percentage, e.g., 10 means 10%).
- Total volume (t) – the result in µL, which you can convert to mL by dividing by 1000.
This is a planning calculation; it does not account for the dead volume inside the master mix tube or the pipette tip, so always prepare a bit more than the exact total.
Worked Example
Using the default values: reaction volume = 25 µL, number of reactions = 10, overfill allowance = 10%.
- First, find the overfill factor: 10% = 0.10, so 1 + 0.10 = 1.10.
- Multiply the reaction volume by the number of reactions: 25 µL × 10 = 250 µL.
- Multiply by the overfill factor: 250 µL × 1.10 = 275 µL.
- Convert to mL: 275 µL ÷ 1000 = 0.275 mL.
The calculator returns 275 µL (0.275 mL) as the total volume to prepare for 10 reactions of 25 µL each with a 10% overfill.
Assumptions
- All reactions have the same volume.
- The overfill allowance is a fixed percentage, not a fixed volume.
- Pipetting losses are uniform across all transfers.
- You are using standard 0.2 mL PCR tubes or a 96-well plate with 0.2 mL wells.
Standard PCR Tube Sizes and Their Uses
The 0.2 mL tube is the most common because it matches the heating block of virtually every standard thermal cycler. The block has wells that are 0.2 mL in capacity, and the tube fits snugly to ensure efficient heat transfer. The 0.5 mL tube is larger and was common in older machines; it is still used when you need a bigger reaction volume or when you are working with a cycler that has 0.5 mL wells. The 0.1 mL tube (often called a “low-profile” tube) is used in some qPCR instruments that require a thinner tube for faster thermal cycling. Always check your instrument’s manual to confirm which tube size it accepts.
PCR tubes are made of polypropylene, which can withstand the repeated heating and cooling cycles (typically 4°C to 95°C) without degrading. They are also chemically resistant to the reagents used in PCR, including buffers, salts, and enzymes. Most tubes are supplied with attached or separate caps to prevent evaporation during cycling.
How Tube Volume Affects Your PCR
The tube volume is not just about fitting the liquid; it affects the thermal performance of the reaction. A smaller tube has a higher surface-area-to-volume ratio, which allows faster heat transfer. This is why 0.1 mL tubes are used in fast PCR protocols. However, you must not overfill the tube. The maximum working volume for a 0.2 mL tube is typically 100–125 µL, even though the nominal capacity is 200 µL. Overfilling can cause the cap to pop off during heating, leading to sample loss and contamination. Conversely, underfilling (e.g., using 5 µL in a 0.2 mL tube) can lead to excessive evaporation because the liquid spreads as a thin film. Most protocols recommend a reaction volume between 10 and 50 µL for 0.2 mL tubes.
How to Choose the Right Tube Size
Choosing the right tube depends on your thermal cycler and your reaction volume. Here are the key factors:
- Instrument compatibility – Check the block type: 0.2 mL, 0.5 mL, or 0.1 mL. Using the wrong tube will not fit or will not heat correctly.
- Reaction volume – For 10–50 µL reactions, 0.2 mL is standard. For larger volumes (50–100 µL), a 0.5 mL tube may be needed, but many modern cyclers do not accept 0.5 mL tubes.
- qPCR requirements – Some qPCR instruments require thin-walled 0.1 mL tubes for optical clarity and fast cycling. Check the instrument’s manual.
- Storage – If you are storing the PCR product, 0.2 mL tubes are convenient because they fit standard freezer racks.
When in doubt, use the tube size that your thermal cycler manufacturer specifies. Using an adapter to fit a smaller tube into a larger well is possible but can lead to uneven heating.
Common Problems and How to Avoid Them
One common mistake is confusing the tube’s total capacity with the maximum recommended reaction volume. A 0.2 mL tube can hold 200 µL, but if you fill it to the brim, the cap will not seal properly, and the liquid may boil over during denaturation. Always leave at least 50% headspace. Another issue is using the wrong tube for the cycler – for example, using a 0.5 mL tube in a 0.2 mL block. The tube will not sit properly, and the heating will be inconsistent. Also, be careful with the cap: if the cap is not fully closed, evaporation will occur, changing the concentration of your reaction. Finally, do not reuse PCR tubes – they are single-use, and residual DNA can contaminate your next reaction.
Comparing Tube Types: Single Tubes, Strips, and Plates
PCR tubes come in three main formats: individual tubes, 8-tube strips, and 96-well plates. Individual tubes are best for a few reactions and allow easy labeling. Strips of 8 are convenient for processing multiple samples with a multichannel pipette. Plates are used for high-throughput work and fit directly into the thermal cycler’s block. The volume per well is the same (0.2 mL), but the plate’s wells are fixed, so you cannot remove a single well. For qPCR, plates with a clear optical film are often required. The choice depends on your throughput: 1–10 reactions, use individual tubes; 10–48, use strips; 48–96, use a plate.
Cost and Availability
PCR tubes are inexpensive. A pack of 1,000 individual 0.2 mL tubes typically costs around $10–$20, while strips and plates are slightly more per unit. The cost is not a major factor in choosing a tube, but availability might be – most labs stock 0.2 mL tubes because they are the universal standard. If you use a specialized instrument that requires 0.1 mL tubes, they may be more expensive and less commonly stocked. Always buy from a reputable supplier to ensure the tubes are free of DNase and RNase, which can degrade your sample.
Safety and Handling
PCR tubes are safe to handle, but follow standard lab safety: wear gloves to avoid contaminating the tube with nucleases from your skin. When heating, the tubes can become hot; use forceps or a heat-resistant glove to remove them from the cycler. If you are working with hazardous reagents (e.g., ethidium bromide for gel loading), dispose of tubes properly according to your lab’s waste guidelines. Always follow your lab method, the safety data sheet (SDS) and your supervisor. The tubes themselves are not hazardous, but the contents may be.
Frequently Asked Questions
Can I use a 0.5 mL tube in a 0.2 mL thermal cycler?
No, a 0.5 mL tube is too large to fit into a 0.2 mL well. Some cyclers have interchangeable blocks, but if not, you cannot use a 0.5 mL tube. You would need to use a 0.2 mL tube or an adapter, but adapters are not recommended because they can cause uneven heating.
What is the maximum volume I can put in a 0.2 mL PCR tube?
The absolute maximum is 200 µL, but the recommended maximum is around 100–125 µL. This leaves headspace for the liquid to expand during heating and ensures the cap seals properly. For best results, keep your reaction volume below 50 µL.
Why do some PCR tubes have flat caps and others have dome caps?
Flat caps are used for qPCR because they allow the optical signal from the fluorophore to pass through. Dome caps are for regular PCR and are easier to open. The volume is the same; the cap shape only affects optical detection.
Can I reuse PCR tubes after cleaning?
It is not recommended. PCR tubes are single-use because they can retain DNA or inhibitors even after cleaning, leading to false results. The plastic also degrades after autoclaving. Always use fresh tubes for each reaction.
How do I know if my PCR tube is the right size for my machine?
Check the thermal cycler’s manual or look at the block – it will have wells that are either 0.2 mL or 0.5 mL in diameter. You can also try inserting a tube; it should fit snugly without forcing. If in doubt, ask your lab manager or supervisor.
What is the difference between thin-walled and regular PCR tubes?
Thin-walled tubes have a thinner plastic wall, which allows faster heat transfer. They are often used in fast PCR or qPCR. Regular tubes are slightly thicker and may be more durable. The volume is the same, but thin-walled tubes are more expensive.
Related
Formula used
in v | Reaction volume | µL | 25 | 1 | 200 in n | Number of reactions | - | 10 | 1 | 96 in o | Overfill allowance | % | 10 | 0 | 50 out t | Total volume needed | µL | v * n * (1 + o / 100) | 1 out tml | Total volume in mL | mL | t / 1000 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Within 10 Percent Calculator – How to Use It5.00 %
- W/W Percentage Calculator: Formula & Examples2.92 %
- Percent Equation: Formula & How to Use It
- Percent of a Number Calculator: Find It Instantly20.00 %
- UWW GPA Calculator: How to Compute Your GPA
- PPM to w/w Calculator: Convert Easily5.0000 %