molecalculator

Moles & Molar Mass

Volume of Hemisphere Calculator: Formula & Steps

Calculator No. 01-7535 · Updated · Formula and assumptions shown below

Volume 2.0944 m³
Radius
1 m
Set in the form below
You enter
Radius (m)
You get
Volume (m³)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator works out the volume of a hemisphere from its radius. You enter the radius in any unit, and it returns the volume in cubic units (cubic meters, cubic centimeters, etc.) using the formula V = (2/3)πr³. The result is the exact space enclosed by the curved surface and the flat circular base.

Formula

The volume of a hemisphere is exactly half the volume of a full sphere of the same radius. The standard formula is:

V = (2/3) × π × r³

  • V = volume of the hemisphere (cubic units, e.g., m³, cm³, ft³)
  • π ≈ 3.141592653589793
  • r = radius of the base (same linear unit as the volume’s cube root)

Since a sphere’s volume is (4/3)πr³, halving that gives (2/3)πr³. This formula assumes a perfect mathematical hemisphere—a solid with a flat circular base and a curved surface that is exactly half of a sphere.

Worked Example

Using the default radius of 1 m:

  1. Cube the radius: 1³ = 1
  2. Multiply by π: 1 × 3.141592653589793 = 3.141592653589793
  3. Multiply by 2/3: (2/3) × 3.141592653589793 = 2.094395102393195

So the volume is 2.0944 m³ (rounded to 4 decimal places). The calculator shows the same value.

Assumptions

  • The shape is a perfect hemisphere—not a dome with a different curvature.
  • The radius is measured from the center of the base to the edge of the curved surface.
  • The volume is for a solid hemisphere; for a hollow shell, you would subtract the inner volume.
  • π is used with full precision in the calculation.

When to Use This Calculator

You need the volume of a hemisphere whenever you are working with half-spherical objects or containers. Common real-world cases include:

  • Calculating the capacity of a hemispherical bowl or tank (e.g., a mixing bowl, a decorative pond).
  • Estimating the volume of a dome-shaped structure (like an igloo or a planetarium) if it is exactly hemispherical.
  • Determining the amount of material needed to fill a hemispherical mold or cast.
  • Solving geometry homework or exam problems involving spheres and their halves.

If you have the diameter instead of the radius, divide the diameter by 2 first. If you have the circumference of the base, divide by 2π to get the radius.

How to Read the Result

The result is in cubic units of the radius you entered. For example:

  • Radius in meters → volume in cubic meters (m³)
  • Radius in centimeters → volume in cubic centimeters (cm³)
  • Radius in inches → volume in cubic inches (in³)

To convert to liters, remember 1 L = 1000 cm³. So a hemisphere with radius 10 cm has volume (2/3)π(10³) ≈ 2094.4 cm³, which is about 2.094 L. For a radius in meters, 1 m³ = 1000 L.

Common Mistakes and Misconceptions

A frequent error is using the diameter instead of the radius. The formula requires the radius—if you plug in the diameter, you get a volume that is 8 times too large. Another mistake is forgetting the 2/3 factor and using the full sphere formula (4/3)πr³, which doubles the correct answer.

Some people think the volume of a hemisphere is half the volume of a cylinder with the same radius and height equal to the radius. That is incorrect—the cylinder’s volume is πr³, so the hemisphere is only 2/3 of that, not 1/2.

Rounding early can also cause errors. For instance, using π ≈ 3.14 instead of 3.14159 changes the result by about 0.05%. For most practical purposes that is fine, but for precise engineering or scientific work, use the full value.

Alternatives and Related Calculations

If you need the volume of a full sphere, use V = (4/3)πr³. For a spherical cap (a slice of a sphere cut by a plane), the formula is more complex: V = (πh²/3)(3r − h), where h is the height of the cap. If you have a dome that is not exactly hemispherical (a common architectural shape), you need the spherical cap formula or a numerical integration.

For surface area of a hemisphere, the curved surface area is 2πr², and the total surface area (including the flat base) is 3πr². These are often needed alongside volume in design and manufacturing.

If you are working with a hollow hemisphere (like a bowl with a wall thickness), you need to subtract the inner volume from the outer volume. For example, a hemisphere with outer radius R and inner radius r has volume (2/3)π(R³ − r³).

Frequently Asked Questions

How do I find the radius if I only know the volume?

Rearrange the formula: r = cuberoot( (3V) / (2π) ). For instance, if the volume is 10 m³, then r = cuberoot( (3×10) / (2π) ) ≈ cuberoot(4.7746) ≈ 1.684 m. You can use the cube root function on most calculators.

Does the formula work for a bowl that is not a perfect half-sphere?

No. The formula assumes the curved surface is exactly half of a sphere. A shallower or deeper bowl has a different shape (a spherical cap), and you need the cap formula, which requires the height of the bowl as well as the radius.

What is the volume of a hemisphere with radius 5 cm?

Using V = (2/3)π(5³) = (2/3)π(125) ≈ 261.8 cm³. That is about 0.262 liters. You can verify with this calculator by entering radius 5 cm (but note the calculator uses meters by default, so convert to 0.05 m to get the result in m³, then convert to cm³).

Is the volume of a hemisphere half the volume of a sphere?

Yes, exactly. Since a hemisphere is half of a sphere, its volume is half of the sphere’s volume. The sphere’s volume is (4/3)πr³, so half is (2/3)πr³. This holds for any radius.

Can I use this calculator for a liquid in a hemispherical tank?

Yes, but only if the tank is completely full. If the liquid fills only part of the tank, you need the volume of a spherical cap (the segment of the hemisphere below the liquid surface). That requires the liquid height, not just the radius.

Related

Formula used
in r | Radius | m | 1 | 0
out v | Volume | m³ | (2/3) * pi * r^3 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →