molecalculator

Moles & Molar Mass

Ethanol Formula: C2H5OH Explained

Calculator No. 01-8984 · Updated · Formula and assumptions shown below

Molarity 0.2537 mol/L
Concentration in millimolar
253.70 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
46.07 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This page explains the chemical formula for ethanol, what each part of the formula means, and how the compound behaves. You enter the mass and molar mass of ethanol to calculate the molarity of a solution, and the calculator returns the concentration in mol/L and mmol/L. The formula for ethanol is C2H5OH, which is the standard molecular formula used in chemistry.

Formula

The molecular formula for ethanol is C2H5OH. It is also written as C2H6O or CH3CH2OH. The formula shows that each molecule contains:

  • 2 carbon (C) atoms
  • 6 hydrogen (H) atoms
  • 1 oxygen (O) atom

The condensed structural formula CH3CH2OH is more informative because it shows the hydroxyl group (–OH) attached to a two-carbon chain. The molar mass of ethanol is 46.07 g/mol, calculated as:

M = (2 × 12.011) + (6 × 1.008) + (1 × 15.999) = 24.022 + 6.048 + 15.999 = 46.069 g/mol ≈ 46.07 g/mol

For the molarity calculation above:

c = m / (mm × V) where m is mass in grams, mm is molar mass in g/mol, and V is volume in liters (converted from mL by dividing by 1000).

Worked Example

Using the default values from the calculator: dissolve 2.922 g of ethanol (mm = 46.07 g/mol) in enough water to make 250 mL of solution.

  1. Convert volume to liters: 250 mL / 1000 = 0.250 L
  2. Calculate moles of ethanol: 2.922 g / 46.07 g/mol = 0.06343 mol
  3. Calculate molarity: 0.06343 mol / 0.250 L = 0.2537 mol/L
  4. Convert to millimolar: 0.2537 mol/L × 1000 = 253.7 mM

The calculator shows 0.2537 mol/L and 253.70 mM, matching the manual calculation.

Assumptions

  • The solute is pure ethanol (no water or additives).
  • The final volume is exactly 250 mL after dissolving, not the volume of solvent added.
  • The solution is at room temperature (density changes are ignored for molarity).
  • The molar mass is taken from IUPAC atomic weights (H 1.008, C 12.011, O 15.999).

What Ethanol Is and Where the Formula Comes From

Ethanol (also called ethyl alcohol, grain alcohol, or simply alcohol) is a colorless, volatile liquid that is the intoxicating component of beer, wine, and spirits. Its formula C2H5OH derives from its structure: a two-carbon chain (ethane) where one hydrogen is replaced by a hydroxyl group (–OH). This makes it a primary alcohol. The name “ethanol” comes from the International Union of Pure and Applied Chemistry (IUPAC) nomenclature: “eth-” for the two-carbon chain and “-anol” for the alcohol functional group. The formula is standard in chemistry; informal terms like “EtOH” (where Et stands for ethyl) are used in lab shorthand but are not standard formulas.

How Ethanol’s Formula Determines Its Properties

The –OH group is polar and can form hydrogen bonds with water molecules, which is why ethanol is completely miscible with water in all proportions. The two-carbon chain is nonpolar, giving ethanol some ability to dissolve nonpolar substances. This dual nature makes ethanol a versatile solvent. The formula also explains its combustion: C2H5OH + 3 O2 → 2 CO2 + 3 H2O. The molar mass (46.07 g/mol) is used in stoichiometry to convert between mass and moles, as shown in the calculator above.

How to Use the Formula in Lab Calculations

When preparing ethanol solutions, you often need to know the molarity. The calculator above does that: enter the mass of ethanol, its molar mass (46.07 g/mol for pure ethanol), and the final volume. For example, to make 500 mL of a 0.5 M ethanol solution, you would need:

mass = M × mm × V = 0.5 mol/L × 46.07 g/mol × 0.500 L = 11.52 g

Weigh 11.52 g of ethanol, dissolve in a small amount of water, then add water to reach 500 mL total. Always add solute to a volumetric flask and then fill to the mark, because the final volume is what matters for molarity.

Common Mistakes and Misconceptions

  • Confusing volume of solvent with final volume: Molarity uses final solution volume, not the volume of water added. If you add 250 mL of water to 2.922 g of ethanol, the final volume may be slightly different (though ethanol and water mix non-ideally, the difference is small). Use a volumetric flask.
  • Using the wrong molar mass: Some sources round to 46 g/mol, which is fine for rough work, but for precise calculations use 46.07 g/mol. Also, do not confuse ethanol (46.07) with methanol (32.04) or isopropanol (60.10).
  • Assuming ethanol is a strong electrolyte: It is a non-electrolyte; it does not dissociate into ions in water. The molarity calculation does not involve dissociation factors.
  • Forgetting to convert mL to L: The calculator does this automatically, but if you do manual calculations, remember 1 mL = 0.001 L.

Safety and Handling of Ethanol

Ethanol is flammable and should be kept away from open flames and sparks. It is also a central nervous system depressant; ingestion of concentrated ethanol can cause intoxication and poisoning. In the lab, wear safety goggles and gloves, and work in a well-ventilated area. Ethanol is hygroscopic, so it absorbs water from the air; keep containers tightly sealed. For disposal, follow your institution’s hazardous waste guidelines. Always consult the Safety Data Sheet (SDS) for ethanol before use.

Alternatives and Related Compounds

Methanol (CH3OH) has one carbon and is highly toxic; isopropanol (C3H8O) has three carbons and is used as a disinfectant. Ethanol is preferred for consumable products because it is less toxic than methanol. In the lab, ethanol is often used as a solvent, a fuel for alcohol burners, and a preservative. For DNA precipitation, ethanol is used at cold temperatures; the formula helps calculate the volume needed (typically 2-3 volumes of 100% ethanol).

Frequently Asked Questions

Is ethanol the same as alcohol?

In everyday language, “alcohol” usually means ethanol. Chemically, alcohols are a class of compounds with a hydroxyl group; ethanol is one member. Methanol and isopropanol are also alcohols but are not safe to drink.

What is the difference between C2H5OH and C2H6O?

Both are valid formulas for ethanol. C2H6O is the molecular formula, while C2H5OH is the condensed structural formula that shows the hydroxyl group. The latter is more useful for understanding the structure.

Why is ethanol’s formula sometimes written as EtOH?

EtOH is an abbreviation where “Et” stands for the ethyl group (C2H5). It is common in lab notebooks and informal writing, but it is not a standard formula. The IUPAC name is ethanol.

How do I calculate the molarity of ethanol from percent by volume?

You need the density of ethanol (0.789 g/mL at 20 °C). For a 10% v/v solution, 100 mL contains 10 mL ethanol, which is 10 × 0.789 = 7.89 g. Divide by molar mass (46.07) to get moles (0.1713 mol) and then divide by the total volume in liters (0.100 L) to get 1.713 M. This assumes the final volume is 100 mL.

Does ethanol have a molecular or empirical formula?

The empirical formula is C2H6O (since the ratio 2:6:1 cannot be simplified). The molecular formula is the same because the actual molecule contains exactly 2 carbons, 6 hydrogens, and 1 oxygen. For many compounds, the empirical and molecular formulas differ, but for ethanol they are identical.

Why is ethanol miscible with water?

The hydroxyl group forms hydrogen bonds with water molecules. The short carbon chain does not disrupt water’s hydrogen bonding network significantly, so ethanol mixes completely. Longer alcohols like butanol are less miscible because the nonpolar chain dominates.

Limits of the Molarity Formula

The molarity calculation assumes ideal mixing and that the final volume is exactly the sum of solute and solvent volumes, which is not strictly true for ethanol-water mixtures. When you mix 50 mL ethanol with 50 mL water, the total volume is about 96 mL due to contraction. Therefore, always prepare solutions in a volumetric flask and fill to the mark. Also, molarity changes with temperature because volume expands; for precise work, control temperature. For very concentrated solutions, use molality or mole fraction instead.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 46.07 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →