The gas-law constant R connects pressure, volume, amount of gas, and temperature in the ideal gas equation. This calculator uses the entered pressure, volume, temperature, and amount of gas to calculate the missing gas quantity or condition, with consistent units. Choose the version of R that matches your pressure and volume units; the calculator’s result is the amount of gas in moles.
Formula
The ideal gas equation is PV = nRT. Rearranged to calculate the gas constant, it is R = PV/(nT). In this calculator, pressure P is in pascals (Pa), volume V is in cubic metres (m³), amount n is in moles (mol), and absolute temperature T is in kelvins (K). Since a pascal times a cubic metre equals a joule, R is reported in joules per mole per kelvin, J/(mol·K).
- R is the universal gas constant, approximately 8.31446261815324 J/(mol·K).
- P is the gas pressure in Pa.
- V is the gas volume in m³.
- n is the amount of gas in mol.
- T is the absolute temperature in K, not degrees Celsius.
The second output calculates the amount in moles from PV/RT using the SI value of R. It is a useful cross-check: with consistent measurements and the ideal-gas assumption, it should agree with the amount entered. The first output is the value specifically calculated by the page title’s equation.
Worked Example
Using the defaults, P = 101325 Pa, V = 0.0244654 m³, n = 1 mol, and T = 298.15 K:
R = (101325 Pa × 0.0244654 m³) / (1 mol × 298.15 K)
The numerator is 2479.786155 Pa·m³, or 2479.786155 J. The denominator is 298.15 mol·K. Therefore R = 2479.786155 / 298.15 = 8.317101 J/(mol·K), which the calculator displays as 8.317101.
Using the standard value for the cross-check, ncalc = 101325 × 0.0244654 / (8.31446261815324 × 298.15) = 1.000317 mol, displayed as 1.000317 mol. The slight difference from 1 mol occurs because the default volume is rounded; it is not an alternate value for R.
Assumptions
- The gas is treated as ideal. Real gases can depart from this model, especially at high pressure or near condensation.
- Pressure is absolute pressure, rather than gauge pressure relative to the atmosphere.
- Temperature is in kelvins, and the measured volume and amount refer to the same gas sample and state.
- The standard SI value used for the amount cross-check is R = 8.31446261815324 J/(mol·K).
What R Means and Why It Has Different Values
R is the proportionality constant in the ideal gas law, relating macroscopic properties of a gas. It is called the universal gas constant because the same physical constant applies to ideal gases when the equation’s units are handled consistently. The number printed for R changes when its units change, not because the gas has a different universal constant.
For SI pressure and volume, R is 8.31446261815324 J/(mol·K). With pressure in atmospheres and volume in litres, the equivalent is about 0.0820574 L·atm/(mol·K). With pressure in bar and volume in litres, it is about 0.0831446 L·bar/(mol·K). These are unit conversions of the same constant. For example, using the SI value with volume in litres without converting litres to cubic metres introduces a factor-of-1000 error.
The symbol is an uppercase R in standard chemistry notation. It should not be confused with a lowercase r, which often denotes a radius or another variable in a different formula. In PV = nRT, the intended quantity is the gas constant R.
How to Use the Calculator and Choose Units
Enter matching measurements for a single gas sample. Convert the volume to m³, pressure to Pa, and temperature to K before entering values. The calculator computes PV/(nT), then reports the SI gas constant. Its second result estimates the amount of gas using the exact SI R value.
- Convert litres to cubic metres by dividing by 1000. For example, 24.4654 L = 0.0244654 m³.
- Convert kilopascals to pascals by multiplying by 1000. For example, 101.325 kPa = 101325 Pa.
- Convert Celsius to kelvins by adding 273.15. For example, 25 °C = 298.15 K.
- Use absolute pressure. If a reading is gauge pressure, add the local atmospheric pressure to obtain absolute pressure.
For classroom problems that use L·atm, either keep that unit system and use R = 0.0820574 L·atm/(mol·K), or convert all quantities to SI. Do not mix the two forms of R or combine a pressure in atmospheres with a volume in m³ unless you also convert units.
Common Errors and Limits
The most frequent mistake is treating R as a gas-specific property. It is universal in the ideal-gas equation; what varies across common tables is its numerical representation in different units. Another common error is entering Celsius directly. The gas law requires absolute temperature, so 25 must not be used in place of 298.15 K.
Also check that pressure is absolute, not gauge pressure, and that every input describes the same sample. A gas volume measured at one temperature and pressure cannot be paired with a pressure from another state unless the sample has been brought to that state or the appropriate gas-law calculation is applied. Rounding intermediate values too early can cause small discrepancies, particularly when comparing results from tables.
The ideal gas law is an approximation. It often works well for gases at relatively low pressure and temperatures well above their condensation points. At high pressures or near a phase change, molecular size and intermolecular forces can make measured behaviour depart from PV = nRT. A more detailed model may then be appropriate; the ideal-gas calculator does not correct for those effects.
Frequently Asked Questions
What is the value of R in the gas equation?
In SI units, R = 8.31446261815324 J/(mol·K). The equivalent value is about 0.0820574 L·atm/(mol·K) when volume is in litres and pressure is in atmospheres.
What does R stand for in PV = nRT?
R denotes the universal gas constant, the proportionality constant connecting pressure, volume, amount, and absolute temperature in the ideal gas equation.
Why do gas-constant tables show different values?
They express the same constant using different pressure and volume units. Select the value whose units match the quantities in your equation.
Is R the same for every gas?
Yes. R is universal; the ideal-gas equation uses the same constant for different gases. Real gases may not follow the ideal equation exactly under all conditions.
Can I use Celsius in the gas equation?
No. Convert Celsius to kelvins by adding 273.15. The temperature in PV = nRT must be an absolute temperature.
Is lowercase r the gas constant?
The standard symbol in the ideal gas equation is uppercase R. Lowercase r usually represents another quantity, such as a radius, unless a particular source defines it otherwise.
Related
Formula used
in p | Pressure | Pa | 101325 | 0 in v | Volume | m³ | 0.0244654 | 0 in t | Temperature | K | 298.15 | 0 in n | Amount of gas | mol | 1 | 0 out r | Gas constant R | J/(mol·K) | p * v / (n * t) | 6 out ncalc | Amount from PV/RT | mol | p * v / (8.31446261815324 * t) | 6
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Isotope Percent Abundance Calculator and How to Use It75.91 %
- Percentage Abundance Calculator and How to Find It
- Isotope Fractional Abundance Calculator and Formula0.2409 fraction
- Percent Abundance Formula: Calculate Isotope Percentages25.00 %
- Isotope Percent Abundance Calculator and How to Use It50.00 %
- Isotope Percent Abundance Calculator and How-To Guide75.91 %