molecalculator

Moles & Molar Mass

RCF in a Centrifuge: Meaning, Formula and RPM

Calculator No. 01-2253 · Updated · Formula and assumptions shown below

Relative centrifugal force 280 ×g
Speed in revolutions per minute
5,000 rpm
= Speed
Rotor radius
10 cm
Set in the form below
Speed
5000 rpm
Set in the form below
You enter
Rotor radius (cm), Speed (rpm)
You get
Relative centrifugal force (×g), Speed in revolutions per minute (rpm)
Rounding
0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

RCF in a centrifuge means relative centrifugal force: the acceleration a sample experiences, expressed as a multiple of Earth’s gravitational acceleration. This calculator works out RCF from rotor radius and rotational speed; enter the radius in centimetres and speed in revolutions per minute (rpm) to get the force as ×g.

Formula

For radius in centimetres and rotational speed in rpm, calculate relative centrifugal force with:

RCF = 1.118 × 10−5 × r × rpm2

  • RCF is relative centrifugal force, a ratio commonly reported as ×g; it has no physical unit.
  • r is the distance in centimetres from the axis of rotation to the point in the sample whose force is being described.
  • rpm is rotational speed in revolutions per minute.

The calculator uses the equivalent expression 1.118 × r × (rpm / 1000)2. The coefficient is a rounded form of the conversion from angular speed and radius to acceleration, divided by standard gravitational acceleration. It is appropriate for these specified units; do not substitute a radius in millimetres or metres without converting it to centimetres first.

Worked Example

Using the calculator’s default inputs, the radius is 10 cm and the speed is 5,000 rpm.

  1. Convert the speed for the calculator expression: 5,000 / 1,000 = 5.
  2. Square that value: 52 = 25.
  3. Multiply by the radius and coefficient: 1.118 × 10 × 25 = 279.5.

The result is 279.5 ×g, displayed to zero decimal places as 280 ×g. That rounding is for display; the underlying calculated value is 279.5 ×g.

Assumptions

  • The radius is entered in centimetres and measured from the rotation axis to the sample location being considered.
  • The speed is the rotor’s rotational speed in rpm and is constant for the calculation.
  • The formula reports idealized acceleration relative to standard gravity; it does not account for sample density, friction, liquid motion, or rotor acceleration and braking.
  • Displayed RCF is rounded to a whole number; use the unrounded value where precision matters.

What RCF Means in Centrifugation

RCF is a standard scientific abbreviation for relative centrifugal force. In everyday lab speech and instrument instructions, people also call it “g-force” or simply write “×g.” It is not a separate force measured in newtons: it is the dimensionless ratio of the acceleration at a location in a spinning rotor to standard gravitational acceleration, approximately 9.80665 m/s².

The term describes the effect of rotation on particles or material in a sample. Under centrifugation, particles move through a fluid at rates affected by their size, shape, density, the fluid’s properties, and the applied acceleration. RCF alone does not predict an exact separation time or guarantee a particular result.

The word “centrifugal” comes through New Latin centrifugus, formed from Latin roots meaning “center” and “to flee.” In a rotating reference frame, the outward centrifugal effect is a useful way to describe what a sample experiences. In an inertial frame, the required inward centripetal acceleration keeps the sample moving in a circle. For practical centrifuge settings, RCF is the familiar convention.

How RCF Relates to RPM

RPM tells how fast the rotor turns. RCF tells the acceleration at a particular radius. They are related, but they are not interchangeable: RCF depends on both speed and radius, and speed is squared in the equation. Doubling rpm at the same radius gives four times the RCF; doubling radius at the same rpm gives twice the RCF.

This is why the same rpm can produce different RCF values in different rotors. For example, at 5,000 rpm, a point 5 cm from the axis experiences about 280 ×g, while a point 10 cm away experiences about 559 ×g. The exact values depend on the formula’s rounded coefficient and the radius used.

When a protocol specifies RCF, use the corresponding RCF setting if the centrifuge can calculate it for the selected rotor. When a protocol specifies rpm, do not silently treat the number as ×g. Check the protocol’s units and the rotor documentation before setting the machine.

Choosing the Radius and Reading the Result

The radius is measured from the axis of rotation to a defined point in the sample. Depending on the centrifuge and rotor, documentation may provide a maximum radius, a minimum radius, or a radius associated with a sample’s bottom or average position. RCF varies along the tube because locations farther from the axis experience greater acceleration.

To choose the right value:

  • Use the radius definition required by your method or rotor documentation; do not assume every radius refers to the same point.
  • Use centimetres in this calculator. Convert millimetres by dividing by 10, or metres by multiplying by 100.
  • Make sure the speed is in rpm, not revolutions per second.
  • Report the result as ×g or RCF, and retain enough digits for the method rather than treating a rounded display as exact.

A rotor may have different radii for different tube positions or sample locations. If a procedure requires a specified RCF across a range, consult the centrifuge’s rotor-specific settings rather than relying on a single assumed radius.

Common Errors and Practical Limits

A frequent mistake is to confuse RCF with rpm. Another is to enter the rotor radius in the wrong units: because the formula expects centimetres, entering 100 for a 10 cm radius by mistake produces a result ten times too high. The squared speed term makes rpm errors especially consequential; a 10% speed increase yields about a 21% RCF increase.

RCF is a calculated acceleration, not a complete description of a centrifugation method. Separation also depends on such factors as particle properties, sample viscosity, temperature, rotor geometry, tube placement, run duration, and whether the procedure uses a fixed-angle or swinging-bucket rotor. Follow the validated method for the sample rather than choosing a run solely from an RCF calculation.

Use only a rotor and tubes rated for the intended speed and compatible with the sample. Inspect and load equipment according to its instructions, balance opposing positions as specified, secure the lid, and never open a spinning centrifuge. Follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What does RCF stand for in a centrifuge?
RCF stands for relative centrifugal force. It expresses rotational acceleration at a chosen radius as a multiple of standard gravitational acceleration, commonly written as ×g.

Is RCF the same as rpm?
No. RPM is rotational speed; RCF is acceleration relative to gravity. The conversion depends on rotor radius as well as rpm, so the same rpm can mean different RCF values in different rotors.

How do I calculate RCF from rpm?
For radius in centimetres, use RCF = 1.118 × 10−5 × radius × rpm². Keep the units consistent, or use the calculator above.

What radius should I use for an RCF calculation?
Use the radius definition specified by the protocol or rotor documentation, measured from the axis to the stated sample location. RCF changes with radius, so a maximum, minimum, or average radius can give different answers.

Why does my centrifuge show a different RCF than my calculation?
Check the selected rotor, the radius convention, units, and whether the displayed value refers to a particular sample position. The calculator’s coefficient and display rounding can also cause small differences from a rotor-specific or more precise calculation.

Related

Formula used
in r | Rotor radius | cm | 10 | 0
in s | Speed | rpm | 5000 | 0
out rcf | Relative centrifugal force | ×g | 1.118 * r * (s / 1000) ^ 2 | 0
out rpm | Speed in revolutions per minute | rpm | s | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →