molecalculator

Moles & Molar Mass

Total Pressure Formula: P = P₁ + P₂ + …

Calculator No. 01-11960 · Updated · Formula and assumptions shown below

Total pressure 1.600 atm
Partial pressure of gas 1
0.8 atm
Set in the form below
Partial pressure of gas 2
0.5 atm
Set in the form below
Partial pressure of gas 3
0.3 atm
Set in the form below
You enter
Partial pressure of gas 1 (atm), Partial pressure of gas 2 (atm), Partial pressure of gas 3 (atm)
You get
Total pressure (atm)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator works out the total pressure of a gas mixture from the partial pressures of its individual components. You enter the partial pressure of each gas (in any consistent unit), and you get back the total pressure, which is simply the sum of all the partial pressures. This is the core of Dalton’s law of partial pressures.

Formula

In words: Total pressure = sum of all partial pressures.

In symbols: Ptotal = P1 + P2 + P3 + …

where:

  • Ptotal is the total pressure of the gas mixture (in atm, Pa, kPa, bar, mmHg, etc.)
  • P1, P2, P3, … are the partial pressures of each individual gas in the same unit.

This is Dalton’s law of partial pressures, named after John Dalton (1766–1844). It holds exactly for ideal gases and is a very good approximation for real gases at ordinary temperatures and pressures.

Worked Example

Using the calculator defaults: gas 1 = 0.8 atm, gas 2 = 0.5 atm, gas 3 = 0.3 atm.

Step 1: Write the equation.
Ptotal = 0.8 atm + 0.5 atm + 0.3 atm

Step 2: Add the numbers.
Ptotal = 1.6 atm

The calculator gives 1.600 atm (rounded to 3 decimal places), which matches.

Assumptions

  • Ideal gas behavior (no intermolecular forces, negligible molecular volume).
  • The gases do not react with each other.
  • All partial pressures are measured at the same temperature and in the same container volume.

For real gases at high pressure or low temperature, deviations occur, but the formula remains a good first approximation.

When to Use This Formula

You use the total pressure formula whenever you have a mixture of gases and you know the partial pressure of each component. Common situations include:

  • Collecting a gas over water – the total pressure is the atmospheric pressure, and the partial pressure of the dry gas is found by subtracting the water vapor pressure.
  • Calculating the pressure in a scuba tank that contains a mixture of oxygen, nitrogen, and other gases.
  • Determining the total pressure in a reaction vessel where several gaseous products are formed.
  • Understanding respiratory physiology – the partial pressures of oxygen and carbon dioxide in the lungs.

You also use it in reverse: if you know the total pressure and the mole fraction of a gas, you can find its partial pressure with Pi = Xi × Ptotal.

How to Read the Result

The total pressure is simply the sum, so the result is in whatever unit you used for the inputs. If you mix units (e.g., one gas in atm, another in kPa), the calculator will give a meaningless number because it doesn’t convert units. Always convert all partial pressures to the same unit before adding.

The result tells you the overall pressure exerted by the mixture on the walls of its container. It is always larger than any individual partial pressure (since all partial pressures are positive).

For example, if you have 0.8 atm of nitrogen and 0.2 atm of oxygen, the total pressure is 1.0 atm. That means the mixture behaves as if it were a single gas at 1 atm pressure.

Common Mistakes and Misconceptions

  • Mixing units: Adding 0.8 atm + 500 mmHg gives a wrong number. Convert to one unit first (1 atm = 760 mmHg).
  • Forgetting water vapor: When collecting a gas over water, the total pressure includes water vapor. The dry gas pressure is Ptotal − Pwater.
  • Assuming total pressure equals the sum of partial pressures only for ideal gases: It’s an excellent approximation for most real gases at low to moderate pressures.
  • Thinking partial pressure is the same as mole fraction: They are related (Pi = XiPtotal) but not identical.
  • Adding pressures of gases at different volumes: Partial pressures are defined for a fixed volume and temperature. If you mix gases at different volumes, you must first calculate the final pressure of each gas in the combined volume using Boyle’s law.

Limits of the Formula

The formula assumes ideal gas behavior. At high pressures (e.g., >10 atm) or very low temperatures, real gases deviate because intermolecular forces become significant. The van der Waals equation is a more accurate alternative, but for most laboratory and everyday applications, Dalton’s law is sufficient.

Also, the formula assumes the gases do not react. If gases react (e.g., H2 and O2 to form water), the total pressure changes over time, and you must account for the reaction stoichiometry.

Finally, the formula gives the total pressure only if you know all the partial pressures. If you only know total pressure and mole fractions, use the mole fraction formula instead.

Frequently Asked Questions

What is the difference between total pressure and partial pressure?

Partial pressure is the pressure that one gas in a mixture would exert if it alone occupied the entire container. Total pressure is the sum of all partial pressures. For example, in air at 1 atm, the partial pressure of nitrogen is about 0.78 atm, oxygen about 0.21 atm, and other gases make up the rest; the total is 1 atm.

How do I calculate total pressure from mole fractions?

If you know the total pressure and the mole fraction of each gas, use Pi = Xi × Ptotal. To get total pressure from mole fractions, you need the partial pressures of all components; then sum them. If you have the number of moles of each gas, use the ideal gas law to find each partial pressure: Pi = niRT/V, then sum.

Does total pressure depend on the type of gas?

No, for ideal gases. At the same temperature and volume, the total pressure depends only on the total number of moles of gas particles, not on their identity. This is why you can simply add partial pressures.

Can I use this formula for liquids?

No. Dalton’s law applies to gases. For a liquid mixture, the total vapor pressure is given by Raoult’s law (for ideal solutions) or more complex models. The total pressure of a liquid system is the sum of the vapor pressures of the components, but that’s a different concept.

What if I have more than three gases?

You can add as many partial pressures as you need. The calculator above has three inputs, but the formula extends to any number. For example, air has nitrogen, oxygen, argon, carbon dioxide, and water vapor – just add them all.

Why does the total pressure sometimes seem less than the sum of partial pressures?

That should never happen for ideal gases. If you see that, it’s likely due to a measurement error, a reaction consuming gas, or a mistake in units. In real gases at very high pressure, small deviations can occur, but the sum is always very close to the actual total pressure.

Related

Formula used
in p1 | Partial pressure of gas 1 | atm | 0.8 | 0 | 100
in p2 | Partial pressure of gas 2 | atm | 0.5 | 0 | 100
in p3 | Partial pressure of gas 3 | atm | 0.3 | 0 | 100
out ptot | Total pressure | atm | p1 + p2 + p3 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →