molecalculator

Moles & Molar Mass

Medium-Range Rotor Radius: What the Term Means

Calculator No. 01-2835 · Updated · Formula and assumptions shown below

Radius from diameter 1.000 m
Rotor diameter
2 m
Set in the form below
You enter
Rotor diameter (m)
You get
Radius from diameter (m)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

There is no standard engineering quantity called the “radius of a medium range rotor,” and “medium range” does not identify a single rotor size. A rotor’s radius is the distance from its axis of rotation to a specified point, commonly the tip of a blade; to give a numerical radius, you need the rotor’s dimensions or a defined application and model.

Formula

For a circular rotor, the radius is half its diameter:

r = d / 2

  • r is the radius, in metres (m).
  • d is the rotor’s diameter, in metres (m), measured across the circle swept by the rotor.

This calculator reports the radius implied by a supplied diameter. It does not determine what size qualifies as “medium range,” because that phrase has no universal rotor-size definition. The default diameter of 2 m is simply an example input, not a recommended or representative size for any particular machine.

Worked Example

Using the default diameter, d = 2 m:

r = d / 2

r = 2 m / 2 = 1.000 m

The calculated radius is 1.000 m, rounded to the three decimal places shown by the calculator. This is a mathematical result for the entered diameter, not a specification for a “medium-range” rotor.

Assumptions

  • The rotor’s swept outline is circular and has a single meaningful axis of rotation.
  • The entered diameter is measured through the axis, from one outer edge of the swept circle to the opposite edge.
  • The result is a geometric radius, not a safe operating limit, performance estimate, or design recommendation.

What “Medium Range Rotor” Means

“Rotor” is a standard technical word for a rotating part or assembly. The exact part depends on the machine: a rotor may be the rotating assembly in an electric motor, the blades and hub of a helicopter, or another component that turns about an axis. In rotorcraft discussions, the phrase “rotor radius” usually means the distance from the rotor shaft or hub axis to the blade tip.

By contrast, “medium range rotor” is not a recognized, stand-alone size class with a fixed radius. “Medium range” is context-dependent wording: it might be used informally to distinguish a machine’s operating range, market category, or scale from smaller and larger examples. Without a named classification system, manufacturer specification, or application, it cannot be translated into a particular length. The wording is therefore not enough to calculate a radius.

The word rotor comes through Latin rotor, meaning “that which rotates,” from rotare, “to turn.” In technical usage, its meaning is supplied by the equipment being discussed. A sentence such as “The rotor radius is 1.2 metres” is clear if the rotor and measurement convention are already identified. “The medium-range rotor has a radius of 1.2 metres” makes a more specific claim, but the phrase “medium-range” still needs a stated context to be meaningful.

How to Measure the Radius

If a datasheet gives the rotor diameter, divide that value by two. Ensure that it refers to the relevant rotor boundary. For a helicopter or wind turbine, the swept diameter is ordinarily measured from one blade tip to the opposite blade tip through the rotation axis. The radius is then the hub-axis-to-tip distance. If the document already lists “rotor radius,” do not halve that figure again.

When the diameter is unavailable but a straight-line distance from the axis to the outer edge is known, that distance is already the radius. Keep units consistent: convert the diameter before dividing if the answer is wanted in a different unit. For example, a diameter of 600 cm is 6 m; its radius is 3 m. The geometry is the same whether the dimensions describe a propeller, fan, rotorcraft, or another circular sweep.

Real equipment can complicate the measurement. Blades may flex, have swept or curved tips, or be measured from a hub that is not at the exact center of the swept outline. In those situations, use the definition and reference points specified by the relevant technical drawing or standard rather than assuming a simple outside measurement is exact.

Why a Radius Is Not a Range

Radius is a length; range is a separate idea that may describe distance, operating capability, or a broad category. A rotor radius alone does not say how far an aircraft can travel, how much air a fan moves, or how much power a turbine produces. Those outcomes depend on other design details and operating conditions.

For a circular swept area, the area is A = πr², where A is in square metres when r is in metres. This shows why radius can matter: if radius doubles, the ideal circular area is four times as large. But swept area is not the same as performance. Blade shape, rotational speed, pitch, air density, power, and the machine’s purpose also affect behavior. In rotorcraft, for instance, the radius is useful for describing rotor geometry, but it cannot by itself establish aircraft range or payload.

A common misconception is that “medium range” corresponds to a universally agreed midpoint between small and large rotors. No general rule supports that interpretation. A category may be defined within a particular product family or engineering study, but its limits must be taken from that source. Do not infer a radius from the adjective alone.

What Information You Need

To obtain a meaningful numerical answer, identify the specific machine and find one of the following:

  • The rotor diameter or swept diameter, which can be halved.
  • A published rotor radius, with its measurement convention stated.
  • A technical drawing with the axis and outer measurement point clearly marked.

Also check the unit and whether the figure refers to one rotor, a pair of rotors, or the complete machine. A two-rotor system can have two separate radii; the distance between rotor centers is not either rotor’s radius. If you are comparing designs, use figures defined in the same way, since different measurement conventions can make nominally similar numbers misleading.

Frequently Asked Questions

What is the radius of a medium-range rotor?
There is no universal value. “Medium-range rotor” does not define a standard size category. Provide the rotor diameter or a specific model and measurement convention to obtain a numerical radius.

How do you calculate a rotor’s radius?
Divide its diameter by two: r = d / 2. Use the diameter of the circular path or boundary relevant to the application, and keep units consistent.

Is rotor radius the same as blade length?
Not necessarily. Rotor radius is normally measured from the rotation axis to the blade tip. A blade’s physical length may differ because of hub geometry, attachment points, or the way its length is specified.

Does a larger rotor radius mean a longer range?
No. Radius describes geometry, not travel distance. Vehicle or machine range depends on many other factors, and radius by itself cannot establish it.

Is “medium-range rotor” a standard technical term?
Not by itself. It may be an informal or context-specific label, but it has no single accepted radius unless a particular classification or specification defines it.

Related

Formula used
in d | Rotor diameter | m | 2 | 0
out r | Radius from diameter | m | d / 2 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →